• Journal of the Korea Organic Resources Recycling Association
• /
• v.18 no.4
• /
• pp.38-44
• /
• 2010

Foundry sands are made up of silica and some coking agents, such as bentonite or resin, and used as templates for the production of various casting products. Foundry sands, which are repeatedly used, were finally transformed into the waste materials by heat, losing their proper functions. The used foundry sands have been treated as general wastes according to the contents of coking agents used. Silica, however, can be recycled through the proper treatment due to its physical property not to changed by heat. In this study, we have identified and investigated at the occurrence, treatment and recycling status of the used foundry sands, as well as for the regime and inhibitory factors of the recycling of them in domestic and foreign cases.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.73-78
• /
• 2001

Portland cement concrete is made with coarse aggregate, fine aggregate, portland cement, water and, in some cases, selected chemical admixtures such as air-entraining agents, water reducer, superplasticizer, and so on, and mineral admixtures such as fly ash, silica fume, slags, etc. Typically, in the concrete, the coarse aggregate and fine aggregate will occupy approximately 80 percent of the total volume of the final mix. Therefore, the coarse and fine aggregates affect to the properties of the portland cement concrete. As the natural sands are drained, it is necessary and economical to utilize crushed sands(manufactured fine aggregate). It is reported that crushed sands differ from natural sands in gradation, particle shape and texture, and the micro fines in the crushed sands affect to the quality of the portland cement concrete. Therefore, the purpose of this paper is to investigate the characteristics of fresh and hardened concrete with high content of micro fines. This study provides firm data for the use of crushed sands with higher micro fines.

• Journal of Industrial Technology
• /
• v.22 no.A
• /
• pp.119-125
• /
• 2002

In Kwangjin industrial company, mill is operating for the foundry sand production at the rate of 25t/hr from quartzite. Foundry sands fall into four distinct categories: silica sand, lake sand, bank sand, and natural molding sand. Silica sand is a general term used to describe crushed, washed, graded, dried, and cooled clay-free sands. This study was conducted for the investigation of the foundry sand productivity and the life span of the hammer according to the material quality. The life time of hammer from several manufacturer were compared in order to find out the grinding efficiency of the various hammer material. In the result of tests, the life time of high-Mn hammer was 10.5 hours while that of high-Cr was 19.5 hours. The life time in case of typical worn shape hammers was about 12 hours and the average time of a blowhole hammer was about 6.5 hours.

• Advances in concrete construction
• /
• v.10 no.5
• /
• pp.431-441
• /
• 2020

For the purpose of improving the properties of UHPC as well as the economic efficiency in production of the material, Availability of river sands as fine aggregate instead of micro silica sand were investigated. Four different sizes of river sands were considered. Using river sand instead of micro silica sand increased the flowability, and decreased the yield stress and plastic viscosity in rheological properties, and the effect was higher with larger particle size of river sand. It was demonstrated by analyses based on the packing density. In the results of compressive strength and elastic modulus, even though river sand was not as good as micro silica sand, it could provide high strength of over 170 MPa and elastic modulus greater than 40 GPa. The difference in compressive strength depending on the size of river sand was explained with the concept of maximum paste thickness based on the packing density of aggregate. The flexural performance with river sand also presented relatively lower resistance than micro silica sand, and the reduction was greater with larger particle size of river sand. The flexural performance was proven to be also influenced by the difference in the fiber orientation distribution due to the size of river sand.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.6
• /
• pp.493-500
• /
• 2006

This paper concerns the measurement of thermal conductivity of grouting materials for ground loop heat exchanger. A thermal conductivity meter, QTM-500 based on modified transient hot wire method was used to measure the thermal conductivity of neat bentonite and mixtures of bentonite and various additives. Relative to the total mixture mass, as the percent additive was increased the mixture thermal conductivity increased. For the bentonite-silica sand mixtures, the higher density of the sand particles resulted in much higher mixture thermal conductivity. The quartzite and silica sands produced the largest increases in mixture thermal conductivity, while common masonry and limestone sands produced lower thermal conductivity increases.

• Proceedings of the Korea Environmental Mutagen Society Conference
• /
• 2005.05a
• /
• pp.51-82
• /
• 2005

• Journal of the Korea Concrete Institute
• /
• v.27 no.3
• /
• pp.273-281
• /
• 2015

In this paper, the performance of alkali-activated slag cement (AASC) is assessed in terms of compressive strength and drying shrinkage, using three different types of silica sand and river sand. The sand type has an important influence on the properties of AASC mortar. Three silica sands (SS1, SS2 and SS3) and river sand (RS) were considered. Three series of blended sands have been tested. A first series (S1) with RS and SS1, a second series (S2) with RS and SS2 and third series (S3) with RS and SS3 with a different blended ratios. The result shows a very significant influence of the blended sand on the AASC mortar properties. The compressive strength and drying shrinkage related with the particle sizes and blended ratios of sands are investigated considering blended sand properties like fineness modulus (FM) and relative specific surface. The type and blended ratio of sand seems to have very significant and important consequences for the mix design of the AASC mortar.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.5
• /
• pp.205-215
• /
• 1999

Crushable sandy soil grounds are widely found along the coast throughout the world. The ground composed of lime sand, which is characterized by the material with high compressibility due to particle crushing contains carbonate calcium. In this study, in order to clarify the characteristics of the particle crushing as related to the strength and deformation properties of sands, isotropic compression test was carried out on three different types of carbonate sands and a silica sand. A crushability index, K, is proposed in connection with the yielding and particle crushing stress of sands at various relative densities under isotropic compression. It is concluded that the representative crushability index, K, associated with the soil particle strength, can be a key factor in preliminary parameters in evaluating soil crushability.

• Journal of the Korean earth science society
• /
• v.43 no.4
• /
• pp.532-538
• /
• 2022

Under anoxic conditions, this study investigated removal of dissolved As(III) by Si and Al oxides including natural sand, chemically washed sand (silica), alumina, and activated alumina. Despite the similar surface area, natural sand showed greater extents of As(III) sorption than chemically washed sand. This was likely due to the high reactivity of Fe(oxyhydr)oxide impurities on the surface of natural sand. For both sands, As(III) sorption was the greatest at pH 7.1, in agreement with the weakly dissociating tendency of arsenous acid. Also, the least sorption was observed at pH 9.6. At basic pH, elevated silicate, which originated from the dissolution of silica in sands, would compete with As(III) for sorption. Due to the highest surface area, activated alumina was found to quantitatively immobilize the initially added As(III) (6.0×10^-7-2.0×10^-5 M). Alumina showed As(III) sorption compared to or greater than chemically washed sand, although the former had less than 6% of the surface of area the latter. The greater reactivity of alumina than chemically washed sand can be explained by using the shared charge of oxygen.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.713-718
• /
• 2006

This paper concerns the measurement of thermal conductivity of grouting materials for ground loop heat exchanger. A thermal conductivity meter, QTM-500 based on modified transient hot wire method was used to measure the thermal conductivity of neat bentonite and mixtures of bentonite and various additives. Relative to the total mixture mass, as the percent additive was increased the mixture thermal conductivity increased. For the bentonite-silica sand mixtures, the higher density of the sand particles resulted in much higher mixture thermal conductivity.