• Korean Chemical Engineering Research
• /
• v.54 no.5
• /
• pp.653-658
• /
• 2016

Poly(ether-block-amide)(PEBAX$_{(R)}$) resin is a thermoplastic elastomer combining linear chains of hard-rigid polyamide block interspaced soft-flexible polyether block. It was believed that the hard polyamide block provides the mechanical strength and permselectivity, whereas gas transport occurs primarily through the soft polyether block. The objective of this work was to investigate the gas permeation properties of carbon dioxide and methane for PEBAX$^{(R)}$-1657 membrane, and compare with those obtained for other grade of pure PEBAX$^{(R)}$, PEBAX$^{(R)}$-2533 and PEBAX$^{(R)}$ based hybrid membranes. The hybrid membranes based PEBAX$^{(R)}$ were obtained by a sol-gel process using GPTMS ((3-glycidoxypropyl) trimethoxysilane) as the only inorganic precursor. Molecular structure and morphology of membrane were analyzed by $^{29}Si$-NMR, DSC and SEM. PEBAX$_{(R)}$-2533 membrane exhibited higher gas permeability coefficients than PEBAX$^{(R)}$-1657 membrane. This was explained by the increase of chain mobility. In contrast, ideal separation factor of $CO_2/CH_4$ for PEBAX$^{(R)}$-1657 membrane was higher than PEBAX$^{(R)}$-2533 membrane. It was explained by the decrease of diffusion selectivity caused by increase of chain mobility. For PEBAX$^{(R)}$/GPTMS hybrid membrane, gas permeability coefficients were decreased with reaction time. Gas permeability coefficient of $CH_4$ was more significantly decreased than $CO_2$. It can be explained by the reduction of chain mobility caused by the sol-gel process, and strong affinity of PEO segment with $CO_2$. Comparing with pure PEBAX$^{(R)}$-1657 membrane, ideal separation factor of $CO_2/CH_4$ for PEBAX$^{(R)}$/GPTMS hybrid membrane has decreased to 4.5%, and gas permeability coefficient of $CO_2$ has increased 3.5 times.

• Korean Journal of Soil Science and Fertilizer
• /
• v.10 no.1
• /
• pp.49-53
• /
• 1977

In order to know the effect of lime application on the phosphorus and silicate, lime and phosphorus were applied in the soil where phosphorus concentration was low and pH 5.4 The results are as follows 1. The filled grain ratio increases by applying the lime in moderate quantity, conversely the large amount of lime reduced the number of panicles per hill and number of spikelets per panicle. 2. The phosphorus application increased the panicle number, grain number and filled grain ratio. Similarly the yield was also significantly increased. 3. Among the inorganic matter of plant absorbed at the heading time the nitrogen contents was highly correlated with the number of heads, grain number per head and yield, while contents of $P_2O_5$ and $SiO_2$ were significantly correlated with the grain number maturerate and yield respectively. 4. Under the lime application the silica of soil was partly correlated with yield and yield components. But there was a significant difference between contents of $P_2O_5$ in soil and yield componentas. And in the plot of double application of neutralizing lime, significance of 1% level was shown between the $P_2O_5$ in soil and the panicles number and grain number respectively, where as significance of 5% with yield. 5. The phosphorus concentration in soil was gradually increased by the increment of lime application. Also the rate of available silicate in soil was considerably increased by the increment of lime application. That is, the silicated concentration in soil was 86ppm with lime and 59ppm without lime.

• Economic and Environmental Geology
• /
• v.49 no.6
• /
• pp.445-458
• /
• 2016

Most of water curtain cultivation (WCC) area in Korea has been inveterately suffering from the gradual draw-down of groundwater level and related shortage of water resources at the late stage of WCC peak time. To solve this problem, artificial recharge techniques has been recently applied to some WCC area. This study introduces infiltration gallery, which is one of the artificial recharge methods, and tentatively examined the effectiveness of three galleries installed at Sangdae-ri WCC area of Cheongju City. Seven galleries are set up at each empty space between eight vinyl houses in this area and its dimension is designed as 50 cm in each width and height and 300 cm in each length. Installation process was including bed excavation, backfill with gravels and silica sands, and completion of gallery by equipment of piezometer and covering with non-woven cloth. For each B, C, D gallery, 3 types of test including preliminary, four step and one long-term injection were performed. The first preliminary test showed the rough relations between injection rates and water level rise as follows; 20 cm and 30 cm level rise for $33.29{\sim}33.84m^3/d$ and $45.60{\sim}46.99m^3/d$ in B gallery; 0 cm, 16 cm and 33 cm level rise for $21.1m^3/d$, $33.98m^3/d$ and $41.69m^3/d$ in C gallery; 29 cm and 42 cm level rise for $48.10m^3/d$ and $52.23m^3/d$ in D gallery. Afterwards, more quantitative results estimating effectiveness of artificial recharge were reasoned out through stepped and long-term injection tests, which is expected to be employed for estimating water quantity re-injected into the aquifer through these galleries by natural injection over the period of WCC peak time.

• Applied Biological Chemistry
• /
• v.15 no.1
• /
• pp.77-84
• /
• 1972

A field experiment was conducted to determine the factors responsible in limiting nutrient up take and root activity in low productive paddy fold. Radiosotope of phosphorus-32 was used as a tracer. Results of the study were as follows: 1. On yield components responsible for increase yield indicated that number of ears per panicle and ripening ratio were closely related to increase yield. 2. Root volume or root feeding area has significant influence in increasing rice yield. 3. Root volume indicative of root activity and nutrient uptake can be effected by reasonable water control. 4. The combined application of calcium, silica, and magnesium(as a fused magnesium phosphate. the Kyun-gi Chemical Co. products.) with water control, although under conditions of large amount application of nitrogen, was found to be increased the maturing rate. 5. In the plots of water control, the number of roots per one volume were less than that of the continuous flooding plots, but the weight per root was heavier than the flooding plot ones. 6. Improvement of the present native culture method could effectively increase paddy rice yield.

• Journal of the Korea Concrete Institute
• /
• v.16 no.6 s.84
• /
• pp.805-811
• /
• 2004

In this paper, effects of mixture proportion and material condition on both fundamental properties, drying and autogenous shrinkage of high performance concrete are discussed. According to the results, for the effect of mixture proportion on the fundamental properties, decrease in W/B and unit water content results in reduction of fluidity, while air content has no variation. Compressive strength exhibits an decreasing tendency with an increase in W/B and unit water content do not remarkable affect the compressive strength. For the effect of materials on the fluidity, the fluidity of low heat portland cement(LPC) is smaller than that of ordinary portland cement(OPC). The use of Polycarbonic acid based superplasticizer(PS) has more favorable effect on enhancing fluidity than Naphtalene based superplasticlzer(NS) and Melamine based superplasticizer(MS). Air content of concrete using LPC is larger than that using OPC. The effects of superplasticizer type on the air content is larger in order of MS, PS and NS. The use of LPC exhibited lower strength development at early age than OPC, whereas after 91days, similar level of compressive strength is achieved regardless of cement type. Compressive strength of concrete is not affected by SP type. For the effect of mixture proportion and materials on drying and autogenous shrinkage, an increase in W/B results in reduction of drying shrinkage and an decrease in water content leads to reduce drying shrinkage. Autogenous shrinkage is not observed until 49 days with the concrete mixture with $35\%$ of W/B and $145 kg/m^3$ of water content. This is due to the combination effects of expansion admixture and shrinkage reducing admixture, which causes an offset of autogenous shrinkage. The use of LPC results in a reduction in autogenous shrinkage compared with OPC. SP type has little influence on the autogenous shrinkage. It is found from the results that mixture proportioning of high performance concrete incorporating fly ash, silica fume, expansion admixture and shrinkage reducing admixture is need to focus on the increase in W/B and the reduction in water content and the use of LPC and MS is also required to use to secure the stability against shrinkage properties.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.18 no.3
• /
• pp.157-170
• /
• 2002

The purpose of this study is to analyze the shear bond strength according to kinds of surface treatment agents and resin cements after acid etching of IPS Empress 2. For this purpose, test groups were classified into silane-treated bonding groups, silica-coated group and Targis link applied group. Then, nine bonding groups in total, each three groups per kind, were prepared by using three kinds of resin cements-Panavia F, Variolink II and Rely-X ARC, and thirty test specimens per group were prepared. To examine any changes in the oral environment, the shear bond strength of each test specimen was measured after dipping test for 24 hours and for five weeks, respectively, in distilled water at $37^{\circ}C$ and performing heat cycle 10,000 times in total, each 2,000 times per week, during a five weeks of dipping, under the condition similar to the oral environment. The bond failure modes were also observed by means of a scanning electron microscope. The results are summarized as follows 1. Statically significant differences between the surface conditioning materials were observed. The shear strength of the silane treatment was the highest of all three types of surface treatments(p<0.001). 2. Shear strengths varied significantly for different types of resin luting agents. But bond strength of Targis link surface treatments were not significantly different(p<0.05). 3. No significant difference of bonding strengths was found between storage time conditions(24 hours and 5 weeks). Only group II, IV, VII, IX were significantly different(p<0.05). 4. After thermocycling, the shear bond strengths of all groups were significantly decreased (p<0.05). Group III, V, VI were no significantly different. 5. On the SEM observation of fractured surfaces, all groups were shown complex failure.

• Journal of Mushroom
• /
• v.13 no.1
• /
• pp.56-62
• /
• 2015

A lipase producing bacterium was isolated from button mushroom bed, which showing high clear zone on agar media containing Tributyrin as the substrate. The strain was identified as Burkholderia cepacia by analysis of 16S rDNA gene sequence. Crude lipase (CL) was partially purified from 70% ammonium sulfate precipitation using the culture filtrate of B. cepacia. Immobilized lipases were prepared by cross-linking method with CL from B. cepacia and Novozyme lipase (NL) onto silanized Silica-gel as support. Residual activitiy of the immobilized CL (ICL) and immobilized NL (INL) was maintained upto 61% and 72%, respectively. Biodiesel (Fatty acid methyl ester, FAME) was recovered by transesterification and methanolysis of Canola oil using NaOH, CL and ICL as the catalysts to compare the composition of fatty acids and the yield of FAME. Total FAME content was NaOH $781mg\;L^{-1}$, CL $681mg\;L^{-1}$ and ICL $596mg\;L^{-1}$, in which the highest levels of FAME was observed to 50% oleic acid (C18:1) and 22% stearic acid (C18:0). In addition, the unsaturated FAME (C18:1, C18:2) decreased, while saturated FAME (C16:0, C18:0) increased according to increasing the reaction times with both CL and ICL, supporting CL possess both transesterification and interesterification activity. When reusability of ICL and INL was estimated by using the continuous reaction of 4 cycles, the activity of ICL and INL was respectively maintained 66% and 79% until the fourth reaction.

• Korean Journal of Environmental Agriculture
• /
• v.33 no.4
• /
• pp.388-394
• /
• 2014

BACKGROUND: Aclonifen is used as a systemic and selective herbicide to control a wide spectrum broad-leaf weeds by inhibition carotenoid biosynthesis, and then its MRLs(Maximum Residue Limits) will be determined in onion and garlic. In this study, a new official method was developed for aclonifen determination in agricultural products to routinely inspect the violation of MRL as well as to evaluate the terminal residue level. METHODS AND RESULTS: Aclonifen was extracted from crop samples with acetone and the extract was partitioned with dichloromethane and then purified by silica solid phase extraction(SPE) cartridge. The purified samples were detected GC using an ECD detector. Limits of detection(LOD) was 0.001 mg/kg and quantification(LOQ) was 0.005 mg/kg, respectively. For validation purposes, recovery studies were carried out at three different concentration levels (LOQ, $10{\times}LOQ$, $50{\times}LOQ$, n=5). The recoveries were ranged from 74.3 to 95.0% with relative standard deviations(RSDs) of less than 8%. All values were consistent with the criteria ranges requested in the Codex guidelines(CAC/GL 40). CONCLUSION: The proposed analytical method was accurate, effective and sensitive for aclonifen determination and it will be used to as an official method in Korea.

• The Journal of Engineering Geology
• /
• v.19 no.2
• /
• pp.235-250
• /
• 2009

Environmental elements such as B, Br, and Sr in groundwater from Bukahn-myeon, Yeongcheon, Gyeongbuk Province, were investigated in order to know their origin with emphasis on hydrochemistry. pH ranges from 7.37 to 8.39. B content is 0.41${\sim}$4.62 mg/L with an average 1.74 mg/L and Br content is 0${\sim}$3.24 mg/L with an average 2.22 mg/L, and Sr content is 0.93${\sim}$8.64 mg/L with an average 2.76 mg/L. The water types plotted by the Piper diagram are different but mostly $Ca-HCO_3$. Some constituents contributing to EC are Na, $SO_4$, Cl with high determinative coefficients($R^2$) of 0.85, 0.70, 0.90, respectively. The coefficients($R^2$) of Cl to Na, K, $SO_4$ are 0.54, 0.68, 0.53, respectively. It should be noted that there are high cocfficients($R^2$) of B-Sr and $Sr-SO_4$ with 0.65, 0.64, respectively. The Cl/Br ratios are 5.21${\sim}$30.70 due to significant depletion of Cl. The $SO_4/Cl$ ratios are 1.32${\sim}$27.24 with an average of 5.92, ascribed to abundant introduction of $SO_4$ or significant depletion of Cl. Chemical speciation calculated shows that B exists mostly as $H_3BO_3$ with less $H_2BO^-_3$ and Br exists as only $Br^-$. Sr exists mostly as $Sr^2$ with less $SO_4$. Saturation index represents that goundwater is supersaturated with respect to barite, kaolinite, illite, K-mica, and smectite while it is slightly undersaturated with respect to silica, gypsum, anhydrite, talc, chrysotile, feldspar, kaolinite, illite, K-mica, and smectite. The saturation index of celestine is -2.23${\sim}$-0.13 indicating more Sr can be incorporated into groundwater. Groundwater is still much undersaturated to halite. It is likely that the origin of S and Sr was related to the Yucheon volcanic rocks. Br might be originated from the local geological features with introduction of anthropogenic matters.

• Horticultural Science & Technology
• /
• v.34 no.4
• /
• pp.537-548
• /
• 2016

The objective of this study was to evaluate the antimicrobial activities of 9 kinds of medicinal plants against crown gall in grapevine. The medicinal plants extracted with several solvent systems were screened for in vitro antibacterial activity by the disc diffusion method. The ethanol and ethyl acetate extracts from magic lily flowers, tachys roots, asian plantain flowers and seeds, sweet wormwood leaves, stems and flowers, immature bitter melon fruits, cockscomb flowers, and peach tree resin showed in vitro antimicrobial activities against Rhizobium vitis with growth inhibition zones ranging from 10 to 27 mm in diameter. The minimum inhibitory concentration values of extracts against R.vitis ranged from 10,000 in Asian plantain flower and 50,000 fold diluted extracts in sweet wormwood flowers, stems, leaves, cockscomb leaves and immature bitter melon fruits. The active fractions of ethyl acetate and ethanol extracts from the medicinal plants were partially separated through silica gel column chromatography and thin layer chromatography (TLC). The active fractions were separated at Rf 0.36, 0.69, 0.75, 0.84, and 0.94 in sweet wormwood extracts, Rf 0.96 and 0.99 in cockscomb flower extracts, Rf 0.92 and 0.97 in cockscomb leaf extracts, and Rf 0.85 in immature bitter melon fruit extracts in TLC analysis developed with hexane:ethyl acetate (20:80, v/v) and methanol:chloroform (20:80, v/v). Among extracts from plants with in vitro antimicrobial activities, sweet wormwood, cockscomb leaves, and immature bitter melon fruits showed in vivo antimicrobial activities with inhibition activity of 100, 67, and 83.3%, respectively, in 'Kyoho' grapevine inoculated with R. vitis compared with the untreated control. These findings indicate that extracts of medicinal plants could be used as sustainable candidates to control crown gall disease caused by R. vitis in grapevines.