• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.4
• /
• pp.23-28
• /
• 2003

This paper describes the machining characteristics of a developed micro grooving machine. Experiments have been conducted on the various grooving condition such as spindle revolution speed, feed rate and depth of groove. V and U-shaped blade tool and STD11 workpiece was used in this study. To evaluate the developed micro grooving machine, AE signal obtained from each experimental condition was analyzed, and cutting stability was compared with the surface state. As a result this study presented the process to optimize grooving condition and possibility of application of AE technique in groove machining.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2017.11a
• /
• pp.74-76
• /
• 2017

In this paper, we introduce the CNN-based in-loop technology for HEVC, and analyze the performance of these algorithms through comparative experiments. The current in-loop filters in HEVC are composed of a deblocking filter that removes noise and a sample adaptive offset filter that compensates for signal offsets. A couple of CNN-based filters replacing the roles of these two algorithms are selected and compared.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.215-219
• /
• 1996

We developed a part of hydraulic stroke sensing cylinder for te purpose of position controlbyusing magnetic sensor and evaluated variously its performance its performance. In this paper, for the evaluation of the developed cylinder under various temperature change, thermal control systems are designed and controlled. It is composed of an heater case, temperature sensor, and interface circuits which included SCR(silicon controlled rectifier) for the control of the voltage's phase. To obtain various temperature conditions, the thermal systems are controlled by using Ziegler-Nichols PED tuning method. The thermalcontrol systems are used to experiment to evaluate whether the developed cylinder can obtain a stable output signal for detecting a stroke of the cylinder under the controlled temperature condition.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.8 s.179
• /
• pp.2143-2150
• /
• 2000

An MRC(Magneto-rheological Clutch) has a great potential of application because of its good transmissibility, little wear-out and fast response to electrical control signal. Though many MRCs have been developed for years, there has not been an research on the method to predict the performance of MRC except the simplified mathematical models. But the simplified mathematical models do not fit well since their performance has close relations with shapes of clutches and viscosity distribution throughout the fluids caused by applied magnetic fields. in this study, the CFD and FEM analyses were applied to various shape of MRC and the methods were examined in experiments.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.23 no.2
• /
• pp.118-126
• /
• 2014

In this paper, a new method is proposed for the five-degree-of-freedom precision alignment and stitching of three-dimensional surface-profile data sets. The control parameters for correcting thealignment error are calculated from the surface profile data for overlapped areas among the adjacent measuring areas by using the "least squares method" and "maximum lag position of cross correlation function." To ensure the alignment and stitching reliability, the relationships betweenthe alignment uncertainty, overlapped area, and signal-to-noise level of the measured profile data are investigated. Based on the results of this uncertainty analysis, an appropriate size is proposed for the overlapped area according to the specimen's surface texture and noise level.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.1122-1129
• /
• 2001

In this work, we propose a new type of HDD suspension featuring shape memory ally (SMA) actuator in order to prevent the contact between the slider and disk. The principal design parameters are obtained from the modal analysis using finite element analysis, and then the dynamic model is established to formulate the control scheme for Non-Contact Start/Stop mode drive. Subsequently, a robust Η$_{\infty}$, control algorithm is designed by integrating experimentally-obtained SMA actuator dynamics to the proposed suspension system. The controller is empirically realized and control results for different load/unload profiles are presented in time domain. In addition, the contact signal between the slider and disk is measured by the electrical resistance method.istance method.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.14 no.6
• /
• pp.2649-2669
• /
• 2020

In this paper, we analyze the secrecy performance of single-input multiple-output (SIMO) relay systems over κ-μ shadowed fading channels. Based on considering relay model employing decode-and-forward (DF) protocol, two security evaluation metrics, namely, secure outage probability (SOP) and probability of strictly positive secrecy capacity (SPSC) are studied, for which closed-form analytical expressions are derived. In addition, Monte Carlo results prove the validity of the theoretical derivation. The simulation results confirm that the factors that enhance the security include large ratio of (μ_D, μ_E), (m_D, m_E), (L_D, L_E) and small ratio of (k_D, k_E) under the high signal-to-noise ratio regime.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10b
• /
• pp.306-311
• /
• 1992

We propose software algorithms which provide the characteristics of acceleration/deceleration essential to high dynamic performance at the transient state where industrial robots or CNC machine tools start and stop. The path error, which is one of the most significant factors in performance evaluation of industrial robots and CNC machine tools, is analyzed for linear, exponential, and parabolic acceleration/deceleration algorithms in case of circular interpolation. The analysis shows that the path error depends on the acceleration/deceleration routine and the servo control system. In experiments, the entire control algorithm including the proposed acceleration/deceleration algorithms is executed on the motion control system with a floating point digital signal processor(DSP) TMS320C30 as a CPU. The experimental results demonstrate that the proposed algorithms are very effective in controlling axes of motion of industrial robots or CNC machine tools with the desired characteristics.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.32B no.7
• /
• pp.1025-1035
• /
• 1995

In this paper, we realize a real time digital FM synthesizer based on genetic algorithm using a general purpose digital signal processor. Especially, we synthesize diverse music sounds nicely using a synthesis model consisting of a single modulator and multiple carriers. Also we present genetic algorithm-based technique which determines optimal parameters for reconstruction through FM synthesis of a sound after analyzing the spectrum of PCM data as a standard music sound using FFT. Using the suggested parameter extractiuon algorithm, we extract parameters of several instruments and then synthesize digital FM sounds. To verify the validity of the parameter extraction algorithm as well as realization of a real time digital music synthesizer, the evaluation is first done by listening the sound directly as subjective test. Secondly, to evaluate the synthesized sound objectively with an engineering sense, we compare the synthesized sound with an original one in a time domain and a frequency domain.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.38 no.9
• /
• pp.21-28
• /
• 2001

The economical detection of dual-tone multi-frequency(DTMF) signals is an important factor when developing cost-effective telecommunication equipment. Each chanel has independently a DTMF receiver, and it informs the detected signal to processors. In order to detect the DTMF signals, the receiver use algorithm such DFT, FFT and Goertzel methods. This paper analyze the power spectra of the DTMF receiver by using the QFT algorithm. As experimental results, it show that can the improved performance of the DTMF receiver and can reduce memory waste and the real time processing.