• 한국지반공학회논문집
• /
• 제27권3호
• /
• pp.55-61
• /
• 2011

일반적으로 하천제방 배수통문은 다양한 원인에 의하여 붕괴가 발생하며, 특히 연약지반 상에 말뚝기초를 이용하여 설치된 경우 1) 주변 지반(외부토체)/말뚝기초 처리된 암거 상단(내부토체)의 상대적 침하 차에 의한 배수통문 암거 측벽부의 다짐도 약화, 2) 하이드로릭 플랙처링에 의한 홍수 시 침투수압의 지속적 반복에 의한 측벽부 교란 등에 의해 붕괴가 발생한다. 특히 측벽부는 시공여건상 다짐장비의 접근이 어려운 다짐 취약부이고, 이질재료에 의한 마찰력 감소로 전단저항력이 일반 흙의 전단강도에 비해 1/3 이상 감소하여 발현된다. 이에 본 연구에서는 주변 지반에 인위적인 변형을 발생시키는 방법으로 침하를 모사한 실내 모형실험을 통하여 연약지반 상 말뚝 기초된 배수통문 암거의 상대적 침하에 따른 외부토체/내부토체 발현 메카니즘과 저판확폭에 따른 배수통문 암거 측벽부 다짐도 향상 효과를 비교 분석함으로써 배수통문 저판 확폭을 통한 주변지반 공동 확장 억제기법을 제시하였다.

• 한국지반공학회논문집
• /
• 제25권8호
• /
• pp.5-21
• /
• 2009

암반에 근입된 현장타설말뚝의 주면마찰력에 대한 최근의 연구결과에 따르면 주면마찰력은 암석의 일축압축강도 외에 굴착면의 거칠기, 암반의 재료특성, 초기 수직음력, 말뚝의 직경, 암반의 절리 및 풍화도 등에 크게 영향을 받는 것으로 보고되어 있다. 지금까지 개발된 굴착면 거칠기 시스템들은 공기 중에서만 측정가능하므로 현장의 굴착공내에서 직접 측정하는 것은 불가능하였다. 따라서, 본 연구에서는 수중에서 사용가능한 굴착공 벽면거칠기 측정 시스템(BKS-LRPS)을 개발하였으며, 특수 제작된 보정장치를 통하여 여러 가지 경우에 대한 검증을 수행하였다. 연구결과에 의하면, 개발된 BKS-LRPS는 장치제작조건 및 현장조건을 반영하도록 계획된 검증조건들에 대하여 유효측정영역을 제시할 수 있었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.447-454
• /
• 2003

In this test, two separated oil jacks were placed at bottom of drilled shaft(D = 1,500mm, L = 33m), and maximum upward and downward load of 1,250 tonf was applied. Also, the deformable rod sensors were placed on each level, and axial strains at each level were measured. Because the side skin friction and the end bearing could be measured separately in the Osterberg type pile load test, this test might be more economical and more applicable than a conventional static pile load test. Thus, if this Osterberg type pile load test could be established during design stage, construction cost might be reduced and its application for large diameter pile could be enhance greatly.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제29회 춘계학술대회
• /
• pp.332-338
• /
• 1999

A coupled thermal-mechanical analysis has been presented for the thermal distortions of the ventilated disk brakes during IS braking operations. The FEM results show that the bendings and distortions of the disk toward the left side are decreased, but the sinusoidal distortion of the disk rubbing surface along the arc length of the vent hole is highly increased by increasing the convective air cooling effects, which is heavily related to the squeal, wear and micro-thermal crackings at the rubbing surfaces due to uneven dissipation rates of friction heatings.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권7호
• /
• pp.930-937
• /
• 2011

The characteristics of mean velocity and turbulence have been analyzed in the circular open channel flow using PIV measurement data for a wide range of water depth. The measured data are fitted to a velocity distribution function over the whole depth of the open channel. Reynolds shear stress and mean velocity in wall unit are compared with the analytic models for fully-developed turbulent boundary layer. Both the mean velocity and Reynolds shear stress have different distributions from the two-dimensional boundary layer flow when the water depth increases over 50% since the influence of the side wall penetrates more deeply into the free surface. The cross-stream Reynolds normal stress also has considerably different distribution in view of its peak value and decreasing rate in the outer region whether the water depth is higher than 50% or not.

• 설비공학논문집
• /
• 제1권4호
• /
• pp.297-304
• /
• 1989

Development of a more satisfactory program of computing the performance on a multi-tube evaporator with continuous plate fins is attempted in this study. The fluid flow involving a change of phase make the flow properties and fluid friction factor of refrigerants, the heat transfer coefficients of refrigerant and air sides vary significantly. Taking such variations into account, a useful program is developed to predict the steady state performance of a multi-tube evaporator. The program was applied to an evaporator which has outside diameter of 10.05mm, inside diameter of 9.35mm, length of 5.4m and two rows arraied staggered. Then the variations of refrigerant quality, temperature, pressure, velocity, enthalpy, specific volume and air temperature, tube temperature were discussed. Satisfactory results were presented that the degree of superheat at the outlet side was $4.4^{\circ}C$ and the air temperature drop between the inlet and outlet of the air conditioner was $10^{\circ}C$.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 봄 학술발표회 논문집
• /
• pp.457-464
• /
• 2000

Stereographic method is a general and basic method to analyse sliding failure potential of rock slope. Region of failure analysis using stereographic method extend to curved slope from straight slope in this paper, Curved slope is defined as the multi-face slope with free surface more than two face and has different characteristics from straight single face slope. Individual daylight envelopes of free surfaces are combined into total daylight envelope of multi-face slope. So, sliding envelope of multi-face slope is the daylight envelope except friction cone. Specially, If only single joint set is developed in the slope, single plane sliding(or plane failure) is impossible in the single-face straight slope, but possible in the multi-face slope. In the multi-face slope with only one joint set, single plane sliding occurs when orientation of sliding plane is between two side slope orientation in the sliding envelope.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.305-310
• /
• 2001

Within some degree of journal misalignment, maximum pressure, maximum temperature, bearing load, friction and side leakage in high-speed journal bearing operation are examined under the condition of variable density and specific heat. The results are compared with the calculation results under the conditions of constant density and specific heat, and variable density and constant specific heat. It is found that the effects of variable density and specific heat on shaft misalignment are significant in determining the load capacity of a journal bearing operating at high speed.

• 한국자동차공학회논문집
• /
• 제20권1호
• /
• pp.131-140
• /
• 2012

In this study, using the governing equation for thermohydrodyamic lubrication involving the homogeneous mixture of incompressible fluid derived by based on the principle of continuum mechanics, it is discussed the effects of water within engine oil on the performance of high speed journal bearing of a turbocharger. The governing equations are the general equations being able to be applied on the mixture of Newtonian fluid and non- Newtonian fluid. Here, the fluid viscosity index, n of power-law non-Newtonian fluid is supposed to be 1 for the application of the journal bearing in a turbocharger lubricated with the mixture of two Newtonian fluid, for example, water within engine oil. The results related with the bearing performance are shown that the bearing friction is to decrease and the side leakage and bearing load increase as increasing the water content in an engine oil.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.661-665
• /
• 2002

A lot of investigations have been made in recent years on the equal channel angular pressing (ECAP) which produces ultra-fine grains. The finite element method has been used to investigate this issue. In this paper, pure-Zirconium is considered far ECAP process by three dimensional finite element analysis. The effects of fiction on the deformation behavior have been investigated and compared with two dimensional finite element analysis.