• 대한기계학회논문집
• /
• 제16권6호
• /
• pp.1121-1140
• /
• 1992

본 연구에서는 부착형 칩절단구의 경사면 대신에 원고면으로 형성한 형태 칩 절단구를 고찰하고, 재래형과 비교하여 더 효과적인 칩절단구를 개발 실용화하고자 한 다. 가공법으로서는 연속칩의 처리가 가장 곤란한 선삭을, 공작물로서는 연속칩이 가장 잘 생성되는 SM 20 C의 연강을, 공구재료로서는 P계열의 초경합금을 써서 저속에 서 고속절삭속도까지 시험하였다.

• International Journal of Precision Engineering and Manufacturing
• /
• 제5권3호
• /
• pp.35-42
• /
• 2004

This research describes that the cutting characteristics and tool wear behavior in the micro cutting of three kinds of wear resistant cemented carbides (WC-Co; V40, V50 and V60) using PCD (Poly Crystalline Diamond) and PCBN (Poly crystalline Cubic Boron Nitride) cutting tools by use of the SEM (Scanning Electron Microscope) direct observation method. The purpose of this research is to present reasonable cutting conditions from the viewpoint of high efficient cutting refer to a precise finished surface and tool wear. Summary of the results is as follows: (1) The cutting forces tend to increase as the increase of the weight percentage of WC particles, and the thrust forces was larger than the principal forces in the cutting of WC-Co. These phenomena were different from the ordinary cutting such as cutting of steel or cast iron. (2) The cutting speed hardly influenced the thrust force, because of the frictional force between the cutting tool edge and small WC particles at low cutting speed region such as 2$\mu\textrm{m}$/s. It seemed that the thrust cutting force occurred by the contact between the flank face and work material near the cutting edge. (3) The wear mechanism for PCD tools is abrasion by hard WC particles of the work materials, which leads diamond grain to be detached from the bond. (4) From the SEM direct observation in cutting the WC-Co, it seems that WC particles are broken and come into contact with the tool edge directly. This causes tool wear, resulting in severe tool damage. (5) In the orthogonal micro cutting of WC-Co, the tool wear in the flank face was formed bigger than that in the rake face on orthogonal micro cutting. And the machining surface integrity on the side of the cutting tool with a negative rake angle was better than that with a positive one, as well as burr in the case of using the cutting tool with a negative rake angle was formed very little compared to the that with a positive one.

• 한국정밀공학회지
• /
• 제15권10호
• /
• pp.34-40
• /
• 1998

The burr produced on piece part edges in machining operations must be removed for most parts to function effectively. Although considerable cost have been expended in improving deburring methods, little energy has been applied toward minimizing burrs. This study has been carried out to prevent the burrs produced on pure aluminium under various working condition and specimen shape in turning operations. The computer image processing system was used for measurement of size of burr, such as burr length, burr depth and burr area. The size of burr showed a decreasing tendency with the increase of rake angle and side cutting angle but it increased rapidly with the increase of depth of cut and the cutting speed has no effect on size of burrs. The size of burr rapidly decreased with the increase of edge angle and burrs are not occurred if edge angle is over 80$^{\circ}$.

• 한국기계가공학회지
• /
• 제1권1호
• /
• pp.5-14
• /
• 2002

Hemisphere shapes were machined for different tool paths and machining conditions with ball endmill cutters. It was also found out how feedrate affect the precision of the machining and also tried to study the most suitable feedrate in specific cutting condition. Tool deflection, cutting forces and shape accuracy were measured according to the inclination position of the sculptured surface. As the decreasing of inclination position angle, the tool deflection was increased due to the decreased cutting speed when the cutting edge is approaching toward the center. Tool deflection when upward cutting IS obtained less than that of downward cutting and down-milling in upward cutting showed the least tool deflection for the sculptured surface. For down-milling, the cutting resistance of the side wall direction is larger than that of feed direction. It was found that the tool deflection is getting better as tool path is going to far from the center for convex surface.

• 한국공작기계학회논문집
• /
• 제10권4호
• /
• pp.55-64
• /
• 2001

In this study, hemisphere and cylindrical shapes were machined for different tool paths and machining conditions with ball endmill cutters. Tool deflection, cutting forces and shape accuracy were measured according to the inclination position of the sculptured surface. As the decreasing of inclination position angle, the tool deflection was increased due to the decreased cutting speed when the cutting edge is approaching toward the center. Tool deflection when upward cutting is obtained less than that of downward cutting and down-milling in upward cutting showed the least tool deflection for the sculptured surface. Roundness values were found in least roundness error when down-milling in upward cutting. It is obtained the very little difference between 90。and 45。 of inclination position angle. The best surface roughness value was obtained in upward up-milling and showed different tendency with tool deflection and cutting force. For down-milling, the cutting resistance of the side wall direction is larger than that of feed direction. Therefore, this phenomenon which is received over cutting resistance can be caused of chatter.

• 대한기계학회논문집A
• /
• 제39권1호
• /
• pp.95-103
• /
• 2015

평엔드밀 가공된 측벽 형상에 공구 형상이 미치는 영향에 대하여 알아보고자 한다. 이를 위하여, 공구 형상을 비틀림각, 절삭날 수, 직경으로 구분하여 특징지었으며, 가공면의 기하학적 특성은 서로 직교하는 이송방향 형상과 축방향 형상으로 나누어 고려하였다. 각 방향의 형상 특성은 공구와 공작물 및 절삭날과 공작물의 간섭 영역으로부터 계산한 순간 절삭면적을 바탕으로 추정하였으며, 추정의 타당성을 가공면 형상 및 배분력 측정을 통하여 검증하였다. 연구 결과, 이송방향 형상의 결함은 공구 퇴출 및 공구 경로의 곡률반경이 변하는 구간에서 나타나며, 이외의 구간에서는 축방향 형상의 결함이 주를 이루는 것이 확인되었다. 측벽의 가공정밀도를 향상시키기 위해서는, 상대적으로 직경이 작고, 비틀림각이 큰 절삭날을 많이 갖는 엔드밀을 사용하여 상향절삭 하는 것이 바람직할 것으로 추천된다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 춘계학술대회 논문집
• /
• pp.137-141
• /
• 1993

In the case of a boring bar, the vibration amplitude is generallylarge due to its high slenderness. The boring bat is then modelled as a cantilever with dynamic force acting at the free end and a generalized model of nonlinear continous system is obtained. The Analysis of model is conducted for the specific case with a zero side cutting edge angle. The dynamic behaviour is investigated for machining processes in which the the overlap factor of regenerative effect is considered. The vibration characteristics of boring bar depth of cut rather than feed rate in given slenderness.

• 한국정밀공학회지
• /
• 제19권7호
• /
• pp.71-79
• /
• 2002

A new rapid prototyping process, Variable Lamination Manufacturing using a 4-axis-controlled hotwire cutter and expandable polystyrene foam sheet as a laminating material of the part (VLM-S), has been developed to reduce building time and to improve the surface finish of parts. The objective of this study is to reconstruct the surface of the original 3D CAD model in order to generate mid-slice data using the advancing front technique. The generation of 3D layers by a 4 axis-controlled hot-wire cutter requires a completely different procedure to generate toolpath data unlike the conventional RP CAD systems. The cutting path data for VLM-S are created by VLM-Slicer, which is a special CAD/CAM software with automatic generation of 3D toolpath. For the conventional sheet type system like LOM, the STL file would be sliced into 2D data only. However, because of using the thick layers and a sloping edge with the firstorder approximation between the top and bottom layers, VLM-Slicer requires surface reconstruction, mid-slice, and the toolpath data generation as well as 2D slicing. Surface reconstruction demands the connection between the two neighboring cross-sectional contours using the triangular facets. VLM-S employs thick layers with finite thickness, so that surface reconstruction is necessary to obtain a sloping angle of a side surface and the point data at a half of the sheet thickness. In the process of the toolpath data generation the surface reconstruction algorithm is expected to minimize the error between the ruled surface and the original parts..

• Design & Manufacturing
• /
• 제14권2호
• /
• pp.56-61
• /
• 2020

Recently, research for machining next-generation micro semiconductor processes and micro patterns has been actively conducted. In particular, it is applied to various industrial fields depending on the machining method in the case of FIB (Focused ion beam) milling. In this study, intends to deal with FIB milling machining technology for ultra-precision diamond tool fabrication technology. Ultra-precision diamond tools require nano-scale precision, and FIB milling is a useful method for nano-scale precision machining. However, FIB milling has a problem of Gaussian characteristics that are differently formed according to the beam current due to the input of an ion beam source, and there are process conditions to be considered, such as a side clearance angle problem of a diamond tool that is differently formed according to the tilting angle. A series of process steps for fabrication a ultra-precision diamond tool were studied and analyzed for each process. It was confirmed that the effect on the fabrication process was large depending on the spot size of the beam and the current of the beam as a result of the experimental analysis.