• 한국자동차공학회논문집
• /
• 제12권3호
• /
• pp.152-158
• /
• 2004

An experimental study was performed to determine the fin-side heat transfer and pressure drop of a condenser for automobile. Five sample with different fin height and louver angle were tested, 9mm, 8mm, 7.5mm, 5.4mm and 4.5mm. Results are presented as plot of Colburn j-factor(or heat transfer coefficients) and friction factor(or pressure drop) against the Reynolds number(or inlet air velocity) based on louver pitch, in the range of 110 to 480. The results show that both heat transfer and pressure drop on the fin are mainly affected by the louver angle in a lower range of air velocity, but, by the fin height in a higher range of air velocity. The performance of 5.4mm fin is the highest, compared to other fin sample.

• 한국지열·수열에너지학회논문집
• /
• 제14권4호
• /
• pp.20-26
• /
• 2018

In this study, the performance characteristics of a welded plate heat exchanger was investigated experimentally. Performance tests were carried out according to the flow rate and inlet temperature of working fluid. As a result, the heat transfer capacity increased by 335.5 kW with an increasing the flow rate and temperature difference between hot and cold side. However, the overall heat transfer coefficient was increased with the increase of flow rate, and it was not effected significantly from inlet temperature difference between hot and cold working fluid. The pressure drop was increased by 55.78 kPa with an increasing the frow rate when the flow rate ratio between hot and cold side 1:1. However, the tendency of pressure drop was difference when flow rate ratio wasn't 1:1. In case that the flow rate ratio between hot and cold side was not 1:1, the pressure drop at the low flow rate side was higher than that when the flow rate ratio was 1:1, while pressure drop of the other side was decreased compared to that when the flow rate ratio was 1:1.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권6호
• /
• pp.701-706
• /
• 2005

Pipes, tubes. and tubular sections with external transverse high fins have been used extensively for heating cooling, and degumidifying air and other gases. This work was performed to investigate an air side heat transfer charactieristics of minichannel with tension wound transverse fin. This estimate was confirmed conversion heat capacity the air side surface area enlargement and heat transfer charactieristics performed available inlet tube side hot water mass flux or outlet tube side air frontal air velocity. The most suitable tension wound transverse finned minichannel was measured extremely low in air side pressure drop and fin effectiveness $3.3\~4.4$. The pressure drop $0.9\~2.8Pa$ was ranged frontal air velocity $0.5\~1.2m/s$. It is also appeared that heat transfer in air side could be better conversion heat area which has been increased $330\%$ of heat capacity compared with the bare tube.

• 한국포장학회지
• /
• 제15권3호
• /
• pp.77-81
• /
• 2009

음료와 맥주 제품의 경우 신선도를 유지하기 목적으로 다양한 종류의 유리병이 국내에서 생산되거나 수입되어 유통되고 있다. 실제 트럭으로 국내 운송되는 맥주 유리병 제품의 유통환경에서 진동 특성을 분석하고 이를 바탕으로 트럭 불규칙 진동 특성인 0.52 $G_{rms}$을 진동시험 규격으로 적용하여 예측실험을 실시하였으며, 결론적으로 유리병의 자체의 파손은 관측되지 않았다. 트럭의 적재함 위치별 상하진동 수준에 있어서는 뒷부분에 위치한 가속도계에서 가장 큰 진동 특성(0.17 $G_{rms}$)이 나타났으며, 앞 부분(0.11 $G_{rms}$)과 중간 부분(0.12 $G_{rms}$)은 큰 차이를 보이지 않았다. 낙하 높이와 제품 용량의 종류에 관계없이 바닥면으로 낙하된 유리병의 경우 파손은 관측되지 않았다. 단측면 낙하 시 가장 큰 유리병 파손율을 보였으며, 장측면에 비해 약 2배 높은 유리병 파손율을 나타내었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.25-30
• /
• 2000

Plate and shell heat exchanger(P&SHE) has been applied to the refrigeration and air conditioning systems as evaporators or condensers fur their high efficiency and compactness. The purpose of this study is to analyze the characteristics of pressure drop in plate and shell heat exchanger. An experiment for single phase (low pressure drop in plate and shell heat exchanger was performed. Also numerical work was conducted using the FLUENT code for $ {\kappa}-{\varepsilon}$ model. The dependence of friction factor on geometrical Parameters was numerically investigated. The study examines the internal flow and the pressure distribution in the channel of plate and shell heat exchanger. The results of CFD analysis compared with experimental data, and the difference of frictor factor in plate side and shell side are 10% and 12%, respectively. Therefore, the CFD analysis model is effectively predict the performance of plate and shell heat exchanger.

• 설비공학논문집
• /
• 제15권12호
• /
• pp.1007-1017
• /
• 2003

An experimental study on the air-side pressure drop and heat transfer coefficient of slit fin-tube heat exchanger has been carried out. The data reduction methodology for air-side heat transfer coefficients in the literature is not based on a consistent approach. This paper focuses on new method of data reduction to obtain the air-side performance of fin-tube heat exchanger using R22 and recommends standard procedures for dry and wet surface heat transfer estimation in fin-tube heat exchanger having refrigerant on the tube-side. Results are presented as plots of friction f-factor and Colburn j -factor against Reynolds number based on the fin collar outside diameter and compared with previous studies. The data covers a range of refrigerant mass fluxes of 150∼250 kg/$m^2$s with air flows at velocity ranges from 0.3 m/s to 0.8 m/s.

• 설비공학논문집
• /
• 제15권3호
• /
• pp.220-229
• /
• 2003

An experimental study on the air-side pressure drop and heat transfer coefficient of slit fin-tube heat exchanger has been carried out. The data reduction methodology for air-side heat transfer coefficients in the literature is not based on a consistent approach. This paper focuses on new method of data reduction to obtain the air-side performance of fin-tube heat exchanger using R22 and recommends standard procedures for dry surface heat transfer estimation in fin-tube heat exchanger having refrigerant on the tube-side. Results are presented as plots of friction f-factor and Colburn j -factor against Reynolds number based on the fin collar outside diameter and compared with previous studies. The data covers a range of refrigerant mass fluxes of 150~250 kg/$m^2$s with air flows at velocity ranges from 0.6 m/s to 1.6 m/s.

• 한국가구학회지
• /
• 제21권3호
• /
• pp.253-260
• /
• 2010

The drop handle in the Chosun-Dynasty played a role lifting up the cabinet and box which was attached to and besides this had the decoration function. The scope of this study should include the drop handles from the $18^{th}$ century up to now by investigating and analyzing their definition & function and furthermore the types of their designs. The object of the study was the drop handle having 2 golden fixing parts which are definitive difference from ring or loop, and the design typology of drop handle was concentrated on the handle part, and it can be classified in two types. The one is the figuration of bow, bat, bamboo, fish and bird and so on from the motive of nature on the handle part, and the other one is the drop handle of the simple ㄷ-shape, the temple-symbol shape or geometrical forms. According to the analysis of relics & literature from the past it was found that there were more quantitative nature-motive figurations than the geometrical forms. The nature-motive figurations were again classified in box-, bat-, cloud- bamboo-, fish- and bird-type, and the geometrical forms in ㄷ-shape, the temple-symbol shape and others. The cases applied to furniture are roughly divided into the front-attached type and the side-attached type. In comparison of the drop handle in the Chosun-Dynasty with that of modern times, ㄷ-shape and bow-type keep the long tradition of the drop handles despite of the constructive change partly. Ring-type is similar to the just ring or loop of the part and drop handle with one golden fixing part, while the knob-type shows almost same forms in the past as well as in the modern times. Which type among handles in the modern times has little connection with the past is the reclaimed type, and it was showed in the Chosun-Dynasty and also is showed up to now identically that the man-made hole on the front side of the drawer for the function as handle.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 동계학술발표대회 논문집
• /
• pp.215-220
• /
• 2008

A microchannel PCHE is manufactured by the two technologies of micro photo-etching and diffusion bonding. In this paper, heat transfer and pressure drop characteristics by applying various configuration for the flow channel in the microchannel PCHE is experimentally investigated. The flow channel configurations are designed three types such as straight, wavy and offset strip channels. The performance experiment of each configuration is performed for Reynolds numbers in ranges of $100{\sim}700$ under various flow conditions for the hot side and the Reynolds number of cold side is fixed at 350. The inlet temperatures of the hot side and cold side are conducted as $40^{\circ}C$ and $20^{\circ}C$, respectively. The heat transfer performance of wavy channel, which was similar to that of offset strip channel, was much higher than that of straight channel. The effectiveness of wavy channel and offset strip channel was evaluated as about $0.5{\sim}0.9$. The pressure drop of wavy channel was highest among configurations and that of offset strip channel was lower than that of straight channel because the round curved surface of each strip edge was reduced the pressure loss.

• Journal of the Optical Society of Korea
• /
• 제9권4호
• /
• pp.135-139
• /
• 2005

We demonstrate a simple and effective wavelength-tunable add/drop filter suitable for coarse wavelength division multiplexing (CWDM) systems. The filter consists of two fibers in contact side by side, with identical long-period fiber gratings (LPG) in each fiber. The LPG couples the power in the fundamental core mode to one of the cladding modes, which is then coupled to the same order cladding mode in the other fiber through evanescent-field coupling between two fibers. Finally, the cladding mode in the second fiber is coupled to its core mode with the help of the other LPG. With an optimal longitudinal offset distance of 10 em, coupling efficiency as high as -1.68 dB and side lobes smaller than -24 dB were experimentally obtained. The experimental results agreed well with the theoretical ones. The operating wavelength of the proposed add/drop filter was tunable by varying the temperature. The temperature sensitivity was measured to be -0.43 nm/$^{\circ}C$.