• 대한치과교정학회지
• /
• 제39권4호
• /
• pp.213-224
• /
• 2009

본 연구에서는 세라믹 브라켓 제거에 Er:YAG 레이저 조사가 도움이 되는지 알아보고, 브라켓 제거에 적합한 레이저 조사 방법을 연구하였으며, 또 이렇게 적용된 레이저가 치수와 법랑질에 손상을 주는지도 알아보았다. 총 190개의 치아, 단결정 세라믹 브라켓(MISO), 다결정 세라믹 브라켓(Transcend series 6000)과 KEY Laser3를 사용하였다. 실험군은 세라믹 브라켓의 종류(단결정, 다결정)와 레이저의 에너지(140, 300, 450, 600 mJ)에 따라 분류하였으며, 레이저를 브라켓당 두 곳에 1펄스씩 조사하고, 전단 강도를 측정하였다. 대조군은 레이저를 조사하지 않는 군으로 하였다. 레이저 조사에 의한 열 효과는 브라켓 하방 법랑질과 치수강에서 측정하였으며, 전단 강도 측정 후 치면에 남아있는 접착제의 양을 접착제 잔류 지수(adhesive remnant index)를 이용하여 평가하였다. 레이저 조사로 인한 접착제의 파괴 양상과 법랑질 표면 변화를 주사전자현미경으로 관찰하였다. 모든 세라믹 브라켓군에서 레이저 에너지가 증가할수록 전단 강도는 유의하게 감소하였다. 또한, 브라켓 하방 법랑질에서 최대 온도 변화는 평균 $3.78^{\circ}C$ 상승에 그쳤으며, 치수강에서 최대 온도 변화는 평균 $0.9^{\circ}C$ 상승에 그쳤다. 주사전자현미경을 이용한 법랑질과 접착제 단면 관찰에서 접착제 표면이 레이저에 의해 붕괴되어 분화구 모양의 구덩이로 관찰되었으며, 일부 시편에서 약 $10\;-\;30{\mu}m$의 법랑질 손상이 발견되었다. Transbond XT로 부착된 단결정 도재 브라켓(MISO)의 디본딩에 Er:YAG 레이저를 이용할 경우, 300 - 450 mJ의 레이저 에너지를, 그리고 다결정 도재 브라켓(Transcend series 6000)의 경우는 450 mJ 정도의 에너지를 사용하는 것이 효과적이고 안전할 것으로 생각된다.

• Bulletin of the Korean Chemical Society
• /
• 제31권4호
• /
• pp.976-980
• /
• 2010

A series of arylacetylene resins with siloxane units were synthesized by the condensation reactions of m-diethynylbenzene magnesium reagents with various $\alpha,\omega$-bis(chloro)dimethylsiloxanes. These resins are liquids and are miscible with common organic solvents at room temperature. The structures of the resins were characterized by FT-IR, $^1H$ NMR, $^{13}C$ NMR, $^{29}Si$ NMR, and gel permeation chromatography (GPC). The thermal behaviors of the resins were examined with differential scanning calorimetry (DSC). These resins have good processability. They can be thermally cross-linked through the ethynyl groups to produce cured resins. The thermal and thermooxidative stabilities of the cured resins were studied by thermogravimetric analysis (TGA). The cured resins possess high thermal and thermooxidative stability. Their decomposition occurs at above $500^{\circ}C$ in both $N_2$ and air. With increasing the length of siloxane units in the resins, the thermal stability of the cured resins decreases in $N_2$. When the cured resins were sintered above $1450^{\circ}C$ under argon, hard and glassy SiOC ceramics were obtained. These SiOC ceramics have the decomposition temperatures at 5% weight loss above $800^{\circ}C$ in air.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제55권8호
• /
• pp.417-422
• /
• 2006

This paper presents the effect of driving waveform for piezoelectric bend mode inkjet printhead with optimized mechanical design. Experimental and theoretical studies on the applied driving waveform versus jetting characteristics were performed. The inkjet head has been designed to maximize the droplet velocity, minimize voltage response of the actuator and optimize the firing frequency to eject ink droplet. The head design was carried out by using mechanical simulation. The printhead has been fabricated with Si(100) and SOI wafers by MEMS process and silicon direct bonding method. To investigate how performance of the piezoelectric ceramic actuator influences on droplet diameter and droplet velocity, the method of stroboscopy was used. Also we observed the movement characteristics of PZT actuator with LDV(Laser Doppler Vibrometer) system, oscilloscope and dynamic signal analyzer. Missing nozzles caused by bubbles in chamber were monitored by their resonance frequency. Using the water based ink of viscosity of 4.8 cps and surface tension of 0.025 N/m, it is possible to eject stable droplets up to 20 kHz, 4.4 m/s and above 8 pl at the different applied driving waveforms.

• The Korean Journal of Ceramics
• /
• 제2권1호
• /
• pp.25-32
• /
• 1996

Solid electroyte nasion was synthesized by the optimized solid state reaction minimizing the volume fraction of secondary $ZrO_2$ and glassy phases. To compensate for the evaporation of Na and P during heat-treatment, excess Na and P were added to the starting composition $Na_{1+x} Zr_2 Si_x P_{d-x} O_{12}$ (x=2.1). Phases pure nasicon comparable in volume fraction to the one obtaied from sol-gel process were synthesized after the reaction at $1100~1150^{\circ}C$,$ P_{O2}>=0.1-0.15 $$ZrO_2$ increased with the heat-treatment time due to the decomposition of nasicon phase and that of glassy phase increased as partial oxygen pressure decreased. The synthesized nasion showed a good electrical conductivity of $-1{\times}10^{-2}({\omega}{\cdot}cm)^{-1}$ at $350^{\circ}C$.

• The Korean Journal of Ceramics
• /
• 제6권1호
• /
• pp.27-31
• /
• 2000

A series experiments were performed to evaluate mechanical behavior of non-oxide boride type ceramics formed on the AISI 1040 plain carbon steel. Boronizing was performed in a slurry salt bath consisting of borax, boric acid, and ferro-silicon at $950^{\circ}C$ for 2-6h. The AISI 1040 steel used as substrate material was containing 0.4%C, 0.13%Si, 0.65%Mn, 0.02%P, 0.014%S. The presence of non-oxide boride type ceramics $Fe_2B $ and FeB formed on the surface of steel was confirmed by metallographic technique and X-ray diffraction (XRD) analysis. The hardness of borides measured via Vickers indenter with a load of 2N reached a microhardness of up to 1800 DPN. The hardness of unborided steel was 185 DPN. The fracture toughness of borides measured by means of Vickers indenter with a load of 10N was about 2.30 MPa.$m^{1/2}$. The thickness of boride layers ranged from 72$\mu\textrm{m}$ to 145$\mu\textrm{m}$. Boride layers have a columnar morphology.

• 한국전기전자재료학회논문지
• /
• 제17권9호
• /
• pp.942-946
• /
• 2004

The crystalline and dielectric properties on Al$_2$O$_3$ filled glass frit (CaO-Al$_2$O$_3$-SiO$_2$-MgO-B$_2$O$_3$) with admixtures of TiO$_2$ have been investigated. The dielectric constant value of 7.5 ∼ 7.8, qualify factor value of 700 were obtained for glass frit : Al$_2$O$_3$(50 : 50 wt%) ceramics. Addition of TiO$_2$ less than 5 wt% slightly increased the dielectric constant from 7.8 to 8.8 due to higher dielectric constant of TiO$_2$. With increasing the amount of TiO$_2$ up to 5 wt%, the temperature coefficient of dielectric properties was improved. When the TiO$_2$ 5 wt% were added, dielectric properties were dielectric constant 8.8, quality factor 840 and the temperature coefficient of dielectric 45 ppm/$^{\circ}C$ at a sintering temperature 920$^{\circ}C$.

• 한국태양에너지학회 논문집
• /
• 제27권1호
• /
• pp.75-81
• /
• 2007

Steam reforming of methane using Xe-arc solar simulator was studied for the application of concentrated solar energy into chemical reaction. The reactor, a volumetric absorber, consisted of a porous ceramic foam disk coated with commercial reforming catalyst. Operating temperature was in the range of $450\;-\;550^{\circ}C$ and the excess steam ratio to methane was from 3.0 to 5.0. At the steady-state condition, the conversion of methane Increased with temperature in the range of 15 % - 30 % and the experimentally determined conversion was found to be close to theoretical equilibrium conversion. It was also found that the CO selectivity slightly decreased with excess steam ratio. Finally, the conversion of methane decreased significantly with space velocity of reactants.

• 한국표면공학회지
• /
• 제29권5호
• /
• pp.570-576
• /
• 1996

Cu films for future ULSI metallization were prepared by partially ionized beam (PIB) deposition and characterized in terms of preferred orientation, grain size, roughness and resistivity. PIB-Cu films were prepared on Si (100) at pressure of $8 \times 10^{-7}$~$1 \times 10^{-6}$ Torr. Effects of acceleration voltage and ionization potential on the properties of PIB-Cu films have been investigated. As the acceleration voltage increased at constant ionization potential of 400 V, the degree of preferred orientation and surface smoothness of the Cu film increased. At the ionization potential of 450 V, the degree of preferred orientation at the acceleration voltage higher than 2 kV decreased and surface roughness increased with acceleration voltage. Grain size of Cu films increased to 1100 $\AA$ initially up to applied acceleration voltage of 1 kV, above which a little increase occurred with the acceleration voltage. There was no indication of impurities such as C, O in all sample. Resistivity of Cu film had the same trends as the surface roughness with acceleration voltage and ionization potential. The increase of electrical resistivity of PIB-Cu films was explained in terms of grain size and surface roughness

• 청정기술
• /
• 제25권3호
• /
• pp.179-188
• /
• 2019

석탄화력 발전시 석탄은 석탄회로 발생하게 되는데 비회(fly ash)가 80%, 저회(bottom ash)가 20% 비율로 발생된다. 그러나 이들 대부분은 재활용되지 못하고 매립장에 전량 폐기되고 있고, 비회 및 저희를 매립하는 매립장이 포화될 경우 새로운 대체 매립장을 건설하지 못하는 한 석탄화력발전소의 운영을 중지해야 하는 경우가 발생할 수 있다. 본 연구에서는 비회를 재활용하여 자원화하기 위해 습식 부유선별기술(부선과정)을 이용하여 비회 내 유용성분{미연탄소(unburned carbon, UC), 뮬라이트(ceramic microsphere, CM), 실리카(cleaned ash, CA)}을 회수하였으며, 회수된 유용성분들의 특성분석으로 산업 소재로 재활용 가능성을 조사하였다. 비회로부터 회수된 유용성분의 회수율은 UC 92.10%, CM 75.75%, CA 69.71%로 부선과정을 통하여 UC가 다른 성분보다 회수율이 16 ~ 22% 더 우수한 것으로 나타났다. UC의 연소가능성분(combustible component, CC)은 52.54wt%, 발열량도 $4,232kcal\;kg^{-1}$로 높아서 석탄 기준 C의 함량 100%일 경우 $8,100kcal\;kg^{-1}$로 감안할 때 산업용 연료로 사용이 가능할 것으로 사료된다. CM과 CA의 분리는 pH의 영향으로 UC 보다는 화학적 분리가 효과적이었으며, 회수된 CA의 $SiO_2$ 함량은 78.66wt%, CM의 $SiO_2$ 함량은 53.55wt%로 나타나 산업용 소재로 재활용 가능성을 확인할 수 있었다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1104-1105
• /
• 2006

Several boride sintered bodies such as $TiB_2$, $ZrB_2$, and $SiB_6$ were previously reported. In the present study, the sinterability and physical properties of chromium boride $(CrB_2)$ containing chromium carbide $(Cr_3C_2)$ sintered bodies were investigated in order to determine its new advanced material. The samples were sintered at desired temperature for 1 hour in vacuum under a pressure by hot pressing. The relative density of sintered bodies was measured by Archimedes' method. The relative densities of $CrB_2$ addition of 0, 5, 10, 15 and 20 mass% $Cr_3C_2$ composites were 92 to 95%. The Vickers hardness of the $CrB_2$ with 10 and 15 mass% $Cr_3C_2$ composites were about 14 and 15 GPa at room temperature, respectively. The Vickers hardness at high temperature of the $CrB_2$ addition of 10 mass% $Cr_3C_2$ composite decreased with increasing measurement temperature. The Vickers hardness at 1273 K of the sample was 6 GPa. The Vickers hardness of $CrB_2$ addition of $Cr_3C_2$ composites was higher than monolithic $CrB_2$ sintered body. The powder X-ray diffraction analysis detected CrB and $B_4C$ phases in $CrB_2$ containing $Cr_3C_2$ composites.