• 열처리공학회지
• /
• 제12권3호
• /
• pp.206-214
• /
• 1999

The effect of cooling rate on carbide precipitation during quenching of austenitic manganese steel was investigated by optical microscopy, image analyzer and numerical analysis. A computer program based on the finite difference method for analyzing heat treatment processes was developed in order to evaluate cooling rates and the possibility of carbide precipitation during quenching. The area ratio of carbide precipitated in the austenite matrix was measured by the image analyzer, and used to determine the critical point of carbide precipitation. Temperature-dependent critical cooling rates at the critical points were calculated using the present simulation program, The calculated results showed a good agreement with the experimental ones.

• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2008년도 정기총회 및 학술발표대회
• /
• pp.679-682
• /
• 2008

Probability precipitation is one of the most important factor for designing the hydrology structures. Probability precipitation is calculated based on the frequency analysis on each durations of annual maximum rainfall data. For frequency analysis we need a conversion factor between the rain data per random-time interval and fixed-time-interval. In this study, the minutely precipitation data on observatory of the Meteorological Administration are used for 37 stations. Therefore, we should conversion factors between the rain data per minute and fixed-time-interval.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2002년도 춘계 학술발표강연 및 논문개요집
• /
• pp.149-149
• /
• 2002

• 한국세라믹학회지
• /
• 제30권2호
• /
• pp.85-92
• /
• 1993

Oxynitride glasses in Na-Ca-Si-O-N system were prepared by melting at 135$0^{\circ}C$ for 2 hours in N2 gas. The effects of Si/Na mole ratio and the various Si3N4 contents were investigated. Stable oxynitride glasses can be obtained up to 9wt.% Si3N4 content in case the Si/Na mole ratio was 2.12 and 1.62, but $\beta$-Si3N4 was precipitated at 9wt.% Si3N4 content in case the Si/Na mole rtio was 1.12. Density (p), chemical durability, hardness (Hv), and fracture toughness (KIC) increased with increasing Si3N4 content. In cae the Si/Na mole ratio was 1.12, the increment of properties was remarkable but hardness and fracture toughness did not increase no longer owing to precipitation of $\beta$-Si3N4.

• 대한화학회지
• /
• 제58권1호
• /
• pp.100-104
• /
• 2014

Magnetite nanoparticles were prepared by co-precipitation method and then silica was coated onto the surface of $Fe_3O_4$ by hydrolysis of TEOS. The silica coated magnetite nanoparticles were characterized for its structural, microstructural, optical, vibrational and magnetic properties by X-ray diffraction analysis, Scanning electron microscopy, UV-visible spectroscopy, Infrared spectroscopy and Vibration sample magnetometer, respectively. XRD study confirmed the presence of $SiO_2$ on the surface of magnetite nanoparticles. SEM study indicated that with increase in TEOS content the particles become bigger and mono-disperse. It was also found that the silica coating prevents magnetic particles from aggregation and imparts excellent stability.

• 한국재료학회지
• /
• 제8권4호
• /
• pp.362-367
• /
• 1998

Mg-6Zn-2Cu 및 Mg-6Zn-1.5Si(wt%)합금의 미세조직 및 석출거동을 조사하였다. 합금은 $4 x 10^{-4}$ 의 진공분위기에서 제조하였고 용체화처리는 $435^{\circ}C$에서 8시간 행하였다. Mg-6Zn합금에 1.5wt.%Si를 첨가한 합금에서는 입계 및 입내에 $10\mu\textrm{m}$-2$\mu\textrm{m}$크기의 구형의 $MgZn_{2}$와 $Mg_{2}$Si상이 존재한다. 시효경화거동은 용체화처리된 Mg-6Zn-2Cu 및 Mg-6Zn-1.5Si합금에서 조사되었다. 결정립 미세화에 의한 경도증가효과는 Mg-6Zn-2Cu합금계에서 크게 나타났으나, 시효에 의한 경도증가효과는 Mg-Zn-Si합금계에서 크게 나타났다. 시효처리 후 생성된 석출상들은 투과전자현미경 분석결과 Mg-6Zn-2Cu합금에서는$ Mg_{2}$$Zn_{3}$이었고 Mg-6Zn-1.5Si 합금에서는 $Mg_{2}$$Zn_{11}$ /이었다.

• 한국광물학회지
• /
• 제9권2호
• /
• pp.71-81
• /
• 1996

Dissolution experiments were conducted to understand chemical nature of weathering of anorthosite from the Hadong area. Anorthosite and plagioclase from it were reacted with HCl or KOH solutions under various conditions concerning such as grain size, initial pH of solutions, and shaking Average composition of plagioclase used in the experiment was Na0.32Ca0.71Al1.71Si2.28O8.Under acidic conditions, solution pH increases rapidly in the initial stage and then gradually to reach palteau. Shaking agitates the reaction rate in the initial stage but does not affect after the system reached steady state. Ca and si concentrations show rapid increase and then gradual increase. Al concentration increases rapidly in the early stage and then decreases. Later decrease was interpreted as the precipitation of an Al-bearing material. Different dissolution rates of different constituents of plagioclase together the with precipitation of al-bearing material might be responsible for the non-stoichiometric dissolution of plagioclase.X-ray diffraction analyses on anorthosite before and after dissolution experiment show dissolution rates differ with different lattice planes of plagioclase. It suggests the crystallographic control on dissolution reaction. X-ray photoelectron spectroscopic result shows that the average composition of plagioclase surface reacted with HCL of initial pH 1.97 for 2000 hours is Na0.20Ca0.26Al1.7Si2.3O8. It means that Na- and Ca-depleted H-feldspar is developed without Al-depleted layer on the surface of plagioclase by reaction with HCl and that dissolution reaction takes place sparsely on the surface of plagioclase. Al and Si are dissolved preferentially over Ca from anorthosite powder in KHO solution. Reaction of acid-reacted anorthosite with KOH solution shows the same Si dissolution behavior as in the fresh anorthosite. This indicates that the Al-depleted and Si-enriched layer does not build up on the acid-reacted surface.

• 마이크로전자및패키징학회지
• /
• 제7권3호
• /
• pp.7-11
• /
• 2000

공침법을 이용하여 제조한 $SrTiO_3$분말에 $CuO-SiO_2$첨가물을 혼합하여 저전압구동형 SrTiO$_3$세라믹 바리스터 소자를 제조하였다. $CuO-SiO_2$첨가물을 이용한 $SrTiO_3$세라믹 바리스터제조 공정은 복잡한 공정을 단순화시킬 수 있을 뿐만 아니라, 일반적인 소결온도보다 100~$150^{\circ}C$ 낮은 온도에서도 소결이 되었다. 이 바리스터의 비직선계수($\alpha$) 값은 첨가물 5 wt% 혼합하여 $1350^{\circ}C$에서 하소한 시편에서 8.47의 최고값을 나타냈으며, 이때의 구동전압은 7 V 이하로 낮은 구동전압을 가진 바리스터를 제조할 수 있었다.

• 한국세라믹학회지
• /
• 제34권8호
• /
• pp.886-896
• /
• 1997

To investigate an effect of phase separation on precipitation characteristics of CuCl nanocrystals in CuCl doped nonlinear optical glasses, borosilicate glass systems with 9 different compositions with ~2wt% of CuCl were selected and CuCl doped glasses were prepared by melting and precipitation method. Microstructural properties of the CuCl doped glasses were analyzed by optical absorption spectroscopy, acid elution test, TEM, and EDXS. While phase separation did not occur in Glass A~D, interconnected and droplet microstructures due to phase separation were found in Glass E, F and Glass G~I, respectively. In the particular composition of the matrix glasses in this study, the precipitation of the CuCl particles was observed in the phase separable glasses, not in phase non-separable glasses. The CuCl particles were precipitated in both silica-rich phase region and boronrich phase region of the glass matrix. In the case of 7.7Na2O-36.6B2O3-52.7SiO2(mole%) glass, the larger CuCl particles than those in the silica-rich phase region were observed in the boron-rich phase region.

• 한국재료학회지
• /
• 제20권2호
• /
• pp.65-71
• /
• 2010

In this study, the effect of Sn and Mg on microstructure and mechanical properties of Cu-Fe-P alloy were investigated by using scanning electron microscope, transmission electron microscope, tensile strength, electrical conductivity, thermal softening, size and distribution of the precipitation phases in order to satisfy characteristic for lead frame material. It was observed that Cu-0.14wt%Fe-0.03wt%P-0.05wt%Si-0.1wt%Zn with Sn and Mg indicates increasing tensile strength compare with PMC90 since Sn restrained the growth of the Fe-P precipitation phase on the matrix. However, the electrical conductivity was decreased by adding addition of Sn and Mg because Sn was dispersed on the matrix and restrained the growth of the Fe-P precipitation. The size of 100 nm $Mg_3P_2$ precipitation phase was observed having lattice parameter $a:12.01{\AA}$ such that [111] zone axis. According to the results of the study, the tensile strength and the electrical conductivity satisfied the requirements of lead frame; so, there is the possibility of application as a substitution material for lead frame of Cu alloy.