• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.3
• /
• pp.135-140
• /
• 2019

In this paper, a frequency split type broadband drive amplifier operating in the L, S and C bands was designed and fabricated. Transistor is difficult to efficiently use when the fractional bandwidth of the drive amplifier is more than 100%, In particular, the characteristics of the driving amplifier are important for operating the power amplifier in which the characteristics of the output power and the efficiency are sensitively changed according to the frequency band. A frequency split methods was applied to maximize the bandwidth of a drive amplifier and to divide the output of the drive amplifier into low band and high band so that the transistor of the power amplifier located at the rear of the drive amplifier can be efficiently used. The designed drive amplifier was fabricated in GaAs HBT technology and 9-layer SiP, and verified by the measurements. The fabricated drive amplifier shows a gain of more than 8 dB and an output power of more than 15 dBm in the operating frequency range.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.388-388
• /
• 2016

Chemical mist deposition (CMD) of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) was investigated with cavitation frequency f, solvent, flow rate of nitrogen, substrate temperature $T_s$, and substrate dc bias $V_s$ as variables for efficient PEDOT:PSS/crystalline (c-)Si heterojunction solar cells (Fig. 1). The high-speed camera and differential mobility analysis characterizations revealed that average size and flux of PEDOT:PSS mist depend on f, solvent, and $V_s$. The size distribution of mist particles including EG/DI water cosolvent is also shown at three different $V_s$ of 0, 1.5, and 5 kV for a f of 3 MHz (Fig. 2). The size distribution of EG/DI water mist without PEDOT:PSS is also shown at the bottom. A peak maximum shifted from 300-350 to 20-30 nm with a narrow band width of ~150 nm for PEDOT:PSS solution, whose maximum number density increased significantly up to 8000/cc with increasing $V_s$. On the other hand, for EG/water cosolvent mist alone, the peak maximum was observed at a 72.3 nm with a number density of ~700/cc and a band width of ~160 nm and it decreased markedly with increasing $V_s$. These findings were not observed for PEDOT:PSS/EG/DI water mist. In addition, the Mie scattering image of PEDOT:PSS mist under white bias light was not observed at $V_s$ above 5 kV, because the average size of mist became smaller. These results imply that most of solvent is solvated in PEDOT:PSS molecule and/or solvent is vaporized. Thus, higher f and $V_s$ generate preferentially fine mist particle with a narrower band width. Film deposition occurred when $V_s$ was impressed on positive to a c-Si substrate at a Ts of $30-40^{\circ}C$, whereas no deposition of films occurred on negative, implying that negatively charged mist mainly provide the film deposition. The uniform deposition of PEDOT:PSS films occurred on textured c-Si(100) substrate by adjusting $T_s$ and $V_s$. The adhesion of CMD PEDOT:PSS to c-Si enhanced by $V_s$ conspicuously compared to that of spin-coated film. The CMD PEDOT:PSS/c-Si solar cell devices on textured c-Si(100) exhibited a ${\eta}$ of 11.0% with the better uniformity of the solar cell parameters. Furthermore, ${\eta}$ increased to 12.5% with a $J_{sc}$ of $35.6mA/cm^2$, a $V_{oc}$ of 0.53 V, and a FF of 0.67 with an antireflection (AR) coating layer of 20-nm-thick CMD molybdenum oxide $MoO_x$ (n= 2.1) using negatively charged mist of 0.1 wt% 12 Molybdo (VI) phosphoric acid n-Hydrate) $H_3(PMo_{12}O_40){\cdot}nH_2O$ in methanol. CMD. These findings suggest that the CMD with negatively charged mist has a great potential for the uniform deposition of organic and inorganic on textured c-Si substrate by adjusting $T_s$ and $V_s$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.151-151
• /
• 2013

무기물 기반, Si-based 태양전지에 비해 가볍고 저렴하다는 관점에서 유기태양전지에 대한 연구가 진행되고 있다. 유기태양전지는 Si-based 태양전지에 비해 그 효율이 낮다는 점이 문제로 제기되어 왔지만, 억셉터와 도너의 nanocomposite 구조인 bulk-heterojunction (BHJ) 구조가 개발이 되면서 유기물의 짧은 엑시톤(exciton) 거리를 극복할 수 있게 되어 그 효율이 비약적으로 증가되는 결과를 낳았다. 또한 넓은 범위의 파장을 흡수 할 수 있는 작은 band-gap을 갖는 물질이 개발됨으로써 유기 태양전지의 효율은 점차 증가하고 있다. 최근에는 독일 회사인 Heliatek에서 12%가 넘는 유기태양전지를 발표함으로써 유기태양전지가 Si-based 태양전지를 대체할 수 있는 차세대 에너지 공급원으로의 가능성을 충분히 보였다. 이런 유기 태양전지는 하부 투명전극인 인듐주석산화물(ITO)/정공이동층(PEDOT:PSS)/광흡수층/전자이동층(LiF)/낮은 일함수를 갖는 상부전극인 Al 구조의 일반적인 구조; ITO/전자이동층/광흡수층/정공이동층/높은 일함수를 갖는 상부전극(Ag), 전하의 이동방향이 반대인 역구조 태양전지, 두 가지로 분류할 수 있다. 하지만 소자 안정성의 관점에서 일반적인 구조의 태양전지는 ITO/PEDOT:PSS 계면에서의 화학적 불안정성과, 낮을 일함수를 갖는 상부전극이 쉽게 산화되는 등의 문제가 있어 상부전극으로 높은 일함수를 갖는 전극을 사용하는 역구조 태양전지가 더 유리하다. 이러한 역구조 태양전지에서 효율을 높일 수 있는 요인 중 하나는 전자이동층에 있다. 광흡수층에서 형성되어 분리된 전자가 전극으로 이동하기위해서는 전자이동층을 거쳐야 한다. 하지만 이 전자이동층 내에서의 전자 이동속도가 느리다면, 즉 저항이 크다면 광흡수증과의 계면에서 Back electron trasnfer현상으로 재결합이 일어나게 되어 전극으로 도달하는 전자의 양이 줄어들게 되고, 이는 유기태양전지 효율을 낮추는 요인이 된다. 전자이동층 자체의 저항뿐만 아니라, 전자이동층의 표면 거칠기(morphology) 또한 유기 태양전지의 효율을 좌우하는 요인 중 하나이다. 광흡수층과 전자이동층의 계면에서 전자의 이동이 일어나는데, 전자이동층의 표면 거칠기가 크게되면 그 위에 박막으로 형성되는 광흡수층과의 계면저항이 증가하게 되고, 이는 광흡수층에서 전자이동층으로의 원활한 전자이동을 저해함으로써 소자 효율의 감소를 일으키게 된다. 따라서 우리는 전자이동층인 ZnO 박막의 스퍼터링 조건을 변화시킴으로써 ZnO 층의 두께에 따른 광투과도, 전기전도성 변화 및 유기태양전지의 효율변화와, 표면 거칠기에 따른 광변환 효율 변화를 관찰하고자 한다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.76-76
• /
• 2011

Polymer-fullerene based bulk heterojunction (BHJ) solar cells can be fabricated in large area using low-cost roll-to-roll manufacturing methods. However, because of the low mobility of the BHJ materials, there is competition between the sweep-out of the photogenerated carriers by the built-in potential and recombination within the thin BHJ film [12-15]. Useful film thicknesses are limited by recombination. Thus, there is a need to increase the absorption by the BHJ film without increasing film thickness. Metal nanoparticles exhibit localized surface plasmon resonances (LSPR) which couple strongly to the incident light. In addition, relatively large metallic nanoparticles can reflect and scatter the light and thereby increase the optical path length within the BHJ film. Thus, the addition of metal nanoparticles into BHJ films offers the possibility of enhanced absorption and correspondingly enhanced photo-generation of mobile carriers. In this work, we have demonstrated several positive effects of shape controlled Au and Ag nanoparticles in organic P3HT/PC70BM, PCDTBT/PC70BM, Si-PCPDTBT/PC70BM BHJ-based PV devices. The use of an optimized concentration of Au and Ag nanomaterials in the BHJ film increases Jsc, FF, and the IPCE. These improvements result from a combination of enhanced light absorption caused by the light scattering of the nanomaterials in an active layer. Some of the metals induce the plasmon light concentration at specific wavelength. Moreover, improved charge transport results in low series resistance.

• Current Photovoltaic Research
• /
• v.11 no.2
• /
• pp.39-43
• /
• 2023

Carrier-selective contacts (CSCs) solar cells are considerably attractive on highly efficient crystalline silicon heterojunction (SHJ) solar cells due to their advantages of high thermal tolerance and the simple fabrication process. CSCs solar cells require a hole selective contact (HSC) layer that selectively collects only holes. In order to selectively collect holes, it must have a work function characteristic of 5.0 eV or more when contacted with n-type Si. The VO_x, NiO_x, and CuI_x thin films were fabricated and analyzed respectively to confirm their potential usage as a hole-selective contact (HSC) layer. All thin films showed characteristics of band-gap engergy > 3.0 eV, work function > 5.0 eV and minority carrier lifetime > 1.5 ms.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.11-11
• /
• 2008

ZnO has a very large exciton binding energy (60 meV) as well as thermal and chemical stability, which are expected to allow efficient excitonic emission, even at room temperature. ZnO based electronic devices have attracted increasing interest as the backplanes for applications in the next-generation displays, such as active-matrix liquid crystal displays (AMLCDs) and active-matrix organic light emitting diodes (AMOLEDs), and in solid state lighting systems as a substitution for GaN based light emitting diodes (LEDs). Most of these electronic devices employ the electrical behavior of n-type semiconducting active oxides due to the difficulty in obtaining a p-type film with long-term stability and high performance. p-type ZnO films can be produced by substituting group V elements (N, P, and As) for the O sites or group I elements (Li, Na, and K) for Zn sites. However, the achievement of p-type ZnO is a difficult task due to self-compensation induced from intrinsic donor defects, such as O vacancies (Vo) and Zn interstitials ($Zn_i$), or an unintentional extrinsic donor such as H. Phosphorus (P) doped ZnO thin films were grown on c-sapphire substrates by radio frequency magnetron sputtering with various Ar/ $O_2$ gas ratios. Control of the electrical types in the P-doped ZnO films was achieved by varying the gas ratio with out post-annealing. The P-doped ZnO films grown at a Ar/ $O_2$ ratio of 3/1 showed p-type conductivity with a hole concentration and hole mobility of $10^{-17}cm^{-3}$ and $2.5cm^2/V{\cdot}s$, respectively. X-ray diffraction showed that the ZnO (0002) peak shifted to lower angle due to the positioning of $p^{3-}$ ions with a smaller ionic radius in the $O^{2-}$ sites. This indicates that a p-type mechanism was due to the substitutional Po. The low-temperature photoluminescence of the p-type ZnO films showed p-type related neutral acceptor-bound exciton emission. The p-ZnO/n-Si heterojunction LEO showed typical rectification behavior, which confirmed the p-type characteristics of the ZnO films in the as-deposited status, despite the deep-level related electroluminescence emission.