• Advances in concrete construction
• /
• v.11 no.1
• /
• pp.73-80
• /
• 2021

Rice Husk Ash (RHA) geopolymer paste activated by sodium aluminate were characterized by X-ray diffractogram (XRD), scanning electron microscope (SEM), energy dispersion X-Ray analysis (EDAX)and fourier transform infrared spectroscopy (FTIR). Five series of RHA geopolymer specimens were prepared by varying the Si/Al ratio as 1.5, 2.0, 2.5, 3.0 and 3.5. The paper focuses on the correlation of microstructure with hardened state parameters like bulk density, apparent porosity, sorptivity, water absorption and compressive strength. XRD analysis peaks indicates quartz, cristobalite and gibbsite for raw RHA and new peaks corresponding to Zeolite A in geopolymer specimens. In general, SEM micrographs show interconnected pores and loosely packed geopolymer matrix except for specimens made with Si/Al of 2.0 which exhibited comparatively better matrix. Incorporation of Al from sodium aluminate were confirmed with the stretching and bending vibration of Si-O-Si and O-Si-O observations from the FTIR analysis of geopolymer specimen. The dense microstructure of SA2.0 correlate into better performance in terms of 28 days maximum compressive strength of 16.96 MPa and minimum for porosity, absorption and sorptivity among the specimens. However, due to the higher water demand to make the paste workable, the value of porosity, absorption and sorptivity were reportedly higher as compared with other geopolymer systems. Correlation regression equations were proposed to validate the interrelation between physical parameters and mechanical strength. RHA geopolymer shows comparatively lower compressive strength as compared to Fly ash geopolymer.

• Journal of the Korean Magnetics Society
• /
• v.20 no.4
• /
• pp.143-148
• /
• 2010

This study examined the effects of sheet thickness on electromagnetic wave absorption characteristics and internal microstructure in 92.6%Fe-6.5%Si-0.9%Cr (wt%) alloy flakes/polymer composite sheets available for quasi-microwave band. The composite sheets with the thickness of 0.3, 0.4 and 0.5 mm were prepared by tape casting. A significant decrease in transmission parameter $S_{21}$ and a large increase in power loss were observed for the thick composite sheet in the frequency range of 1~5 GHz. However the permeability properties were not affected by thickness variation, while the imaginary part of complex permittivity increased with the increase of sheet thickness at 1~5 GHz. The enhanced electromagnetic wave absorption characteristics in the thicker composite sheets was attributed to the changed microstructure and the higher dielectric loss.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.5 no.3
• /
• pp.182-186
• /
• 2005

In this work, thermal evaporation system was employed to deposit thin films of SiC on glass substrates in order to determine the parameters of them. Measurements included transmission, absorption, Seebak effect, resistivity and conductivity, absorption coefficient, type of energy band-gap, extinction coefficient as functions of photon energy and the effect of increasing film thickness on transmittance. Results explained that SiC thin film is an n-type semiconductor of indirect energy band-gap of ${\sim}3eV$, cut-off wavelength of 448nm, absorption coefficient of $3.4395{\times}10^{4}cm^{-1}$ and extinction coefficient of 0.154. The experimental measured values are in good agreement with the typical values of SiC thin films prepared by other advanced deposition techniques.

• Journal of the Korean Ceramic Society
• /
• v.27 no.5
• /
• pp.583-588
• /
• 1990

Glass films in the binary system B2O3-SiO2 and Al2O3-SiO2 were prepared on soda-lime-silica slide glass by the dip-coating technique from TEOS and boric acid or aluminum nitrate. Thickness of the films varying with viscosity and withdrawal speed were measured and effect of composition and firing temperature on the properties such as transmittance and refractive index were investigated. nM2O3.(100-n)SiO2(M=B or Al) films containing up to 20mol% B2O3 and 40mol% Al2O3 were transparent. Maximum transmittance at visible range were obtained for the sample containing 15mol% Ba2O3 and 32.5mol% Al2O3 and heat-treated at 50$0^{\circ}C$, respectively. Refractive index of the film containing 15mol% B2O3 was mininum in the B2O3-SiO2 binary system and minimal refractive index was appeared at the film containing 32.5mol% Al2O3. In IP spectra, addition of B2O3 were increased absorption peak intensity of B-O and Si-O-B bond and addition of Al2O3 were decreased absorption peak intensity of Si-O bond, respectively.

• Proceedings of the KIEE Conference
• /
• 1994.11a
• /
• pp.249-251
• /
• 1994

We fabricated the sample of M-I-M with the insulating layer SiO. Refractive index of wave length, photon energy, absorption rate of SiO evaporation thin film are experimentally examined by spectroscopic Ellipsometer. The calculated equations of refractive index, absorption rate and permittivity of SiO thin film are induced. Calculated values and experimental values are compared and then mutual validity is proved.

• Journal of Korean Ophthalmic Optics Society
• /
• v.8 no.1
• /
• pp.7-10
• /
• 2003

Quarternary $SrO-B_2O_3-Al_2O_3-SiO_2$ glasses were fabricated as a function of $R({\equiv}SrO\;mole%/B_2O_3\;mole%)$ and $K({\equiv}(Al_2O_3+SiO_2)\;mole%/B_2O_3\;mole%)$. The structures of these glasses were investigated through Infrared absorption spectra. When R increased, the intensities of the absorption bands around $1,200{\sim}1,600cm^{-1}$ resulting from the B-O stretching vibration bond in the symmetrical trigonal $BO_3$ units decreased, and these of the absorption bands around $800{\sim}1,200cm^{-1}$ caused by the B-O stretching vibration bond of the tetrahedral $BO_4$ units varied. Also, the intensities of the absorption bands for the B-O stretching vibration band in trigonal $BO_3$ units increased and these of the bands for B-O stretching vibration bond in tetrahedral $BO_4$ units decreased as K increased.

• Journal of Sensor Science and Technology
• /
• v.27 no.5
• /
• pp.306-310
• /
• 2018

In order to develop a highly sensitive infrared sensor, it is necessary to develop techniques for decreasing the rate of heat absorption and the transition of the absorption wavelength to a longer wavelength, both of which can be induced by decreasing the pixel size of the bolometer. Therefore, in this study, $1{\mu}m$ hole-arrays with a subwavelength smaller than the incident infrared wavelength were formed on the amorphous silicon-based microbolometer pixels in the absorber, which consisted of a TiN absorption layer, an a-Si resistance layer and a SiNx membrane support layer. We demonstrated that it is possible to reduce the thermal time constant by 16% relative to the hole-patternless bolometer, and that it is possible to shift the absorption peak to a shorter wavelength as well as increase absorption in the $4-8{\mu}m$ band to compensate for the infrared long-wavelength transition. These results demonstrate the potential for a new approach to improve the performance of high-resolution microbolometers.

• Journal of the Korean Ceramic Society
• /
• v.47 no.3
• /
• pp.249-255
• /
• 2010

To investigate optical properties of (V, Pr)-doped $ZrSiO_4$ green pigments, samples were prepared by the ceramic method using NaF and NaCl as mineralizers. They were characterized by X-ray diffraction, UV-Vis spectroscopy and Raman spectroscopy. The changes of color in the samples during heating and effect of mineralizers were studied in terms of valence of the vanadium and praseodymium in the zircon matrix. (V, Pr)-doped $ZrSiO_4$ pigments give rise to green coloration in $800^{\circ}C$. The oxidation state of V and Pr ions of pigments in the glazed samples were confirmed by UV-Vis absorption spectra. This absorption spectra showed three typical bands of trivalent Pr at the 445, 480~490, 592 nm due to f-f transitions and two broad bands of 302~380, 400~500 nm due to f-d transitions of tetravalent Pr. According to the increasing amounts of $Pr_6O_{11}$, the two broad bands showed decreasing intensity at 290, 640 nm due to d-d transitions of tetravalent V.

• Journal of Magnetics
• /
• v.14 no.4
• /
• pp.155-160
• /
• 2009

This study examined the effects of a decrease in thickness of magnetic alloy flakes on the electromagnetic wave absorption characteristics of nanocrystalline $Fe_{73.5}Cu_1Nb_3Si_{15.5}B_7$ (at.%) alloy flakes/polymer composite sheets available for a quasi-microwave band. The thickness of FeCuNbSiB alloy flakes decreased to 1-2 $\mu$m with increasing milling time up to 24 h, and the composite sheet including alloy flakes milled for 24 h exhibited considerably enhanced power loss properties in the GHz range compared to the sheets having non-milled alloy powders. Although a considerable increase in loss factor upon milling was observed in the narrow frequency range of 4-6 GHz, there was no correlation between the complex permeability and flake thickness. However, the complex permittivity increased with increasing milling time, and there was good agreement between the milling time and the frequency dependences of the complex permittivity and power loss.

• Korean Journal of Metals and Materials
• /
• v.46 no.1
• /
• pp.44-51
• /
• 2008

The effects of magnetic powder size on electromagnetic wave absorption characteristics in Fe-6.5Si-0.9Cr(wt%) alloy flakes/polymer composite sheets available for quasi-microwave band have been investigated. The composite sheet including small magnetic flakes with the size less than $26{\mu}m$ exhibited high power loss in the GHz frequency range as compared with the sheets having large alloy flakes of $45{\sim}75{\mu}m$. Moreover, both the complex permeability and the loss factor increased with the decrease in size of the alloy flakes. The large power loss of the sheets containing small magnetic flakes was attributed to the high complex permeability, especially their imaginary part. The high complex permeability of the sheets composed of small flakes was considered to be due to the highly thin shape of the flakes inducing low eddy-current loss.