• Economic and Environmental Geology
• /
• v.44 no.2
• /
• pp.123-133
• /
• 2011

The lab scale experiments to investigate the geochemical reaction among supercritical $CO_2$-mineral-brine which occurs at $CO_2$ sequestration sites were performed. High pressurized cell system (l00 bar and $50^{\circ}C$) was designed to create supercritical $CO_2$ in the cell, simulating the sub-surface $CO_2$ storage site. From the high pressurized cell experiment, the surface changes of Ca-feldspar, amphibole (tremolite) and olivine, resulted from the supercritical $CO_2$-mineral-brine reaction, were observed and the dissolution of minerals into the brine was also investigated. The mineral slabs were polished and three locations on the surface were randomly selected for the image analysis of SPM and the surface roughness value (SRV) of those locations were calculated to quantify the change of mineral surface for 30 days. At a certain time interval, SPM images and SRVs of the same mineral surface were acquired. The secondary minerals precipitated on the mineral surfaces were also analyzed on SEM/EDS after the experiment. From the experiments, the average SRV of Ca-feldspar increased from 2.77 nm to 20.87 nm for 30 days, suggesting that the dissolution of Ca-feldspar occurs in active when the feldspars contact with supercritical $CO_2$ and brine. For the amphibole, the average SRV increased from 2.54 nm to 8.31 nm and for the olivine from 0.77 nm to 11.03 run. For the Ca-feldspar, $Ca^{2+}$, $Na^+$, $Fe^{2+}$, $Si^{4+}$, $K^+$ and $Mg^{2+}$ were dissolved in the highest order and $Si^{4+}$, $Ca^{2+}$, $Fe^{2+}$ and $Mg^{2+}$ for the amphibole. Fe (or Mg) - oxides were precipitated as the secondary minerals on the surfaces of amphibole and olivine after 30 days reaction. Results suggested that $Ca^{2+}$, $Fe^{2+}$ and $Mg^{2+}$ rich minerals would be significantly weathered when it contacts with the supercritical $CO_2$ and brine at $CO_2$ sequestration sites.

• Journal of the Korean Society of Radiology
• /
• v.10 no.2
• /
• pp.109-115
• /
• 2016

Despite of increasing the use of the digital imaging device in the radiology area, the setting on the optimal irradiation conditions are insufficient. In this study, the exposure dose and image quality by exposure condition of digital radiography device were compared. The exposure doses were obtained by adjusting the exposure condition as 5 steps respectively based on the exposure conditions that are currently used of CR and DR radiography devices. The acquired image has been assessed by 20 medical image professors using the assessment method of the Japanese Society for Tuberculosis Prevent. As a result, in the case of the CR system, the better image quality was obtained in the condition of 120 kVp and 1.5 mAs~2.4 mAs (quality score 91~95.5 points) than standard exposure condition(110 kVp, 3.2 mAs, 86 points). And exposure dose was evaluated as low with $61.3{\sim}98.4{\mu}Gy$ than standard condition($105.11{\mu}Gy$). In DR system, however, the image quality score was higher as 97~98.6 points in the lower tube voltage range (112 kVp, 2.4~3.2 mAs) condition than the standard exposure condition (125 kVp, 3.2 mAs, 91 points). In addition, the exposure dose was $61.5-77.2{\mu}Gy$ lower than standard condition($93{\mu}Gy$). In addition, the exposure dose was low as $61.5-77.2{\mu}Gy$ than standard condition($93{\mu}Gy$). With the results of this study, we confirmed that it is possible to reduce the patient exposure dose with the same image quality by adjusting the optimal exposure condition of digital device.

• Journal of Fisheries and Marine Sciences Education
• /
• v.27 no.5
• /
• pp.1352-1363
• /
• 2015

This study was carried out to investigate the characteristics of the dependent variables depending on the condition changes of independent variable of the operation and the material during the production of collets added with rice and dried shrimp by using single extruder to utilize as basic data for the manufacture of extrusion collets. A total of 7 independent variables were set up as a raw, 20, 40 and 60 mesh for the powder particle size of rice; 12, 14, 16 and 18% for the moisture content of rice; 2, 4, 6 and 8% for the addition amount of dried shrimp; 90, 95, 100 and $110^{\circ}C$ for the barrel temperature; 210, 280 and 340 rpm for the screw speed; 4, 6, 8 and 10 mm for the discharge port diameter; 30, 40, 50 and 60 kg/h for the input amount of the mixed material. The characteristics of the dependent variables including puffing ratio, moisture content, lightness, uniformity, productivity of collets was to be studied by changing the conditions of the independent variables. As a results of this study, 20 mesh of powder particle size of rice, 14% of moisture content of rice, 4% of addition amount of dried shrimp, $100^{\circ}C$ of barrel temperature, 280 rpm of screw speed, 6 mm of discharge port diameter and 50 kg/h of input amount of mixed material were found to be the most preferable over other independent variables for the production of extrusion collets. In conclusion, it is necessary to set the independent variable in order to produce the high quality collets added with the rice as the main raw material and dried shrimp as the sub-materials.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.57 no.4
• /
• pp.418-423
• /
• 2012

Field experiments were carried out to improve the cultural practice of potato by analysing its tuberization patterns. Tuberization patterns affected by different altitudes was analyzed at two potato cultivation regions, Jinbu (600 m) and Daegwallyung (800 m) using two potato cultivars, 'Superior' and 'Atlantic'. To analyse tuberization patterns affected by different planting time, seed potatoes were planted at every 10 days from April 19 to May 19 in Daegwallyung. Total dry weight was greater in plant grown at the altitude of 800 m than 600 m during the entire growth period and the highest increase was observed at the early growth period, July 6, comparing to other growth period. The total dry weight was the greatest at 110~112 days after planting (DAP) at the altitude of 800 m and 108~111 DAP at 600 m. There was no significant differences between altitudes and between cultivars. Tuber dry weight per plant at the altitude of 600 m was lower than 800 m on July 6 (58 DAP), but it increased rapidly from July 21 (73 DAP). At both altitudes, the increase of tuber dry weight per plant from July 6 to August 8 was higher than the other growth period. The time of growth period at which tuber dry weight per plant was the highest was similar at both altitudes that was 118~125 DAP at the altitude 800 m and 118~124 DAP at the altitude 600 m. Dry weight per tuber at the altitude 800m was higher than 600 m due to the number of tubers per plant. A higher increase of crop growth rate (CGR) was shown at the altitude 600 m on July 6 (58 DAP), comparing to at 800 m. The highest tuber dry weight per plant of each cultivar was shown when the planting time was April 29 for 'Superior' and was April 19 for 'Atlantic'. Both the tuber dry weight of plant and the total dry weight were lower at a later planting time. Dry weight per tuber increased quickly during the period between June 30 to August 8. Tuberization period was shortened as the planting time was delayed.

• Radiation Oncology Journal
• /
• v.28 no.1
• /
• pp.23-31
• /
• 2010

Purpose: To evaluate the relationship between the normal tissue complication probability (NTCP) of 3-dimensional (3-D) radiotherapy and the radiographic parameters of 2-dimensional (2-D) radiotherapy such as central lung distance (CLD) and maximal heart distance (MHD). Materials and Methods: We analyzed 110 patients who were treated with postoperative radiotherapy for breast cancer. A two-field tangential technique, a three-field technique, and the reverse hockey stick method were used. The radiation dose administered to whole breast or the chest wall was 50.4 Gy, whereas a 45 Gy was administered to the supraclavicular field. The NTCPs of the heart and lung were calculated by the modified Lyman model and the relative seriality model. Results: For all patients, the NTCPs of radiation-induced pneumonitis and cardiac mortality were 0.5% and 0.7%, respectively. The NTCP of radiation-induced pneumonitis was higher in patients treated with the reverse hockey stick method than in those treated by other two techniques (0.0%, 0.0%, 3.1%, p<0.001). The NTCP of radiation-induced pneumonitis increased with CLD. The NTCP of cardiac mortality increased with MHD ($R^2=0.808$). Conclusion: We found a close correlation between the NTCP of 3-D radiotherapy and 2-D radiographic parameters. Our results are useful to reanalyze the previous 2-D based clinical reports about breast radiation therapy complications as a viewpoint of NTCP.

• Korean Journal of Environmental Biology
• /
• v.17 no.4
• /
• pp.529-541
• /
• 1999

In order to elucidate characteristics of water quality, investigation of monthly dynamics of environmental factors and algal populations at major four stations of the mid and lower part in Taechong Reservoir was performed from June 1998 to June 1999. Water temperature, DO and pH were ranged 5.3~27.7$^{\circ}C$, 6.2~13.8 mgO$_2$/1 and 6.4~9.5, respectively. Those were varying as the season changes. Among inorganic nitrogen nutrients, NH$_4$was ranged from 5.5% to 7.2% of NO$_3$and NO$_3$was almost same through the seasons except summer in which it was low. SRP and SRSi were increased in summer when the blue-green algae became dominant. Those were decreased as the cell density of diatom increased when the water temperature dropped. Therefore SRSi was considered to be another important nutrient factor contributing to the increment of biomass of freshwater algae as well as SRP. Average chi-$\alpha$ concentration ranged from s to 12 $\mu$g/1 and in the lower part or the reservoir, the lowest was found. Moreover, there were remarkable increment in summer when TN/TP ratio were decreasing from relationships between TN/TP ratio and chi-$\alpha$ concentration. Annual mean ratio of TN/TP ratio was relatively high as the value was 110, which was relatively high, and it showed that P is the dominant factor in the algal growth. The dynamics of phytoplankton were simply dominated by a few species seasonally. In summer, blue -green algae such as Anabaena, Microcystis and Oscillatoria were dominant and algal bloom of blue -green began from early summer, sustained to late autumn. The average standing crops of A. spiroides v. crassa, M. aeruginosa and O. limosa were ranged 0.3~2.0$\times$10$^4$cells/ml, 6.4$\times$10$^2$~1.0$\times$10$^4$cells/ml and 4.6$\times$10$^3$~1.6$\times$10$^4$cells/ml, respectively. In winter, diatom Stephanodiscus was considered to be an important species whose average standing crops of Stephunodiscus was 4.9$\times$10$^2$cells/ml from November to April of the next year and the highest was 1.3$\times$10$^3$cells/ml in January.

• Korean Journal of Soil Science and Fertilizer
• /
• v.27 no.3
• /
• pp.149-157
• /
• 1994

The conditions for formation of allophane in volcanic ash soils in Cheju Island were investigated. Soils of toposequence distributed along the sourthern slope of Mt. Halla, and the major soil groups such as dark brown soils, very dark brown soils, black soils, and brown forest soils were colleted and analyzed for Al, Fe and Si extracted with solutions of pyrophosphate and oxalate. Mean annual temperature decreased $0.8^{\circ}C$ and mean annual precipitation increased 110mm with increase elevation of 100m. Organic carbon content increased and soil pH decreased with elevation, and the formation of allophane in soils formed a climosequence. Dark brown soils widely distributed in the northern and western coastal areas, where the mean annual precipitation ranged 1,240~1,420mm and the evaporation ranged 1,290~1,320mm, contained only small amounts of allophane and Al-humus complexes. For other soils, organic carbon content, pyrophosphate extractable Al, and $Al_p/Al_o$ were inversely correlated with $pH(CaCl_2)$. Allophane content showed close relationships wlth $pH(CaCl_2)$, and inverse relationships with organic carbon content and $Al_p/Al_o$.

• Journal of Korean Society of Forest Science
• /
• v.110 no.4
• /
• pp.678-688
• /
• 2021

This study was conducted to provide growth characteristics and stand information in preparation for natural regeneration method and silvicultural treatment of seed tree method in Korean red pine stands by using the field inventoried data 18 years after the seed tree regeneration method in 2001 and analyzing the stand and sapling characteristics. The study area was located in the Research Forest of Kangwon National University, Chuncheon-si, Gangwon-do. In November 2018, we collected tree measurement factors, such as diameter at breast height (DBH), height, crown class, stem quality, tree age, and annual height increment on the established plots. We calculated the basal area, volume, height-diameter ratio (HD ratio), and additional stand density variables such as the relative density and %stocking to analyze the managed stands. The number of mother trees was 58 trees/ha, with a 17.7% stocking level, whereas the number of saplings was 2,330 trees/ha, with a 79.0% stocking level. In germination, the age distribution of saplings ranged from 2001 to 2007, with most belonging to 15-16 years. The development condition of saplings was 10 cm in DBH and 8 m in height. DBH and height were higher as the crown class is more dominant, and this difference was statistically significant in the analysis of variance and Duncan's multiple comparison test (p<0.0001). HD ratio ranged mostly between 80% and 90%, and more than 95% of sapling stems were of high quality, with a straight, unbroken top, non-sweep, and non-diseased stem. On average, the annual height increment of saplings was 21.9 cm at 1 year, 43.3 cm at 5 years, 54.3 cm at 10 years, and 64.3 cm at 15 years. The overall height growth with age increased smoothly. According to the analysis of covariance, the annual height growth by crown class differed significantly. The regression analysis parameters revealed that annual height growth increased with age and dominant crown class.

• Journal of Korean Society of Forest Science
• /
• v.110 no.4
• /
• pp.554-568
• /
• 2021

Forests are the largest carbon (C) sinks in terrestrial ecosystems. Recently, as enhancing forest C sequestration capacity has been proposed as a basic direction of the Republic of Korea's "2050 Carbon Neutral Strategy," accurate estimation of forest C sequestration has been emphasized. According to the Intergovernmental Panel on Climate Change guidelines, sequestration quantity is calculated from changes in C stocks in forest C pools, such as biomass, deadwood, litter and soil layer, and harvested wood products. However, in Korea, only the overstory biomass increase is now considered the amount of sequestration quantity, so there can be a significant difference from the actual forest C sequestration. In this study, we quantified forest C exchange through C flux measurement using an eddy covariance system and an automated soil chamber system in a 57-year-old Korean pine plantation located in Mt. Taehwa, Gwangju-si, Gyeonggi-do. Then, the net amount of C sequestration was compared with the amount of the overstory biomass increase. We estimated the annual C stock change in the remaining C pools by comparing the net sequestration amount from the C flux measurement with the overstory biomass increase and C stock change in the litter layer. Therefore, the net C sequestration of the Korean pine plantation estimated from the flux measurement was 5.96 MgC ha^-1, which was about 2.2 times greater than 2.77 MgC ha^-1 of the overstory biomass increase. The annual C stock increase in the litter layer was estimated to be 0.75 MgC ha^-1, resulting in a total annual C stock increase of 2.45 MgC ha^-1 in the remaining C pools. Our results indicate that the domestic forest is a larger C sink than the current methods, implying that more accurate calculations of the C sequestration capacity are necessary to quantify C stock changes in C pools along with the C flux measurement.

• Journal of Korean Society of Forest Science
• /
• v.110 no.4
• /
• pp.504-515
• /
• 2021

To examine the relationship between environmental factors influencing the habitat of Aconitum austrokoreense Koidz., this study employed the MexEnt model to evaluate 21 environmental factors. Fourteen environmental factors having an AUC of at least 0.6 were found to be the age of stand, growing stock, altitude, topography, topographic wetness index, solar radiation, soil texture, mean temperature in January, mean temperature in April, mean annual temperature, mean rainfall in January, mean rainfall in August, and mean annual rainfall. Based on the response curves of the 14 descriptive factors, Aconitum austrokoreense Koidz. on the Baekun Mountain were deemed more suitable for sites at an altitude of 600 m or lower, and habitats were not significantly affected by the inclination angle. The preferred conditions were high stand density, sites close to valleys, and distribution in the northwestern direction. Under the five-age class system, the species were more likely to be observed for lower classes. The preferred solar radiation in this study was 1.2 MJ/m². The species were less likely to be observed when the topographic wetness index fell below the reference value of 4.5, and were more likely observed above 7.5 (reference of threshold). Soil analysis showed that Aconitum austrokoreense Koidz. was more likely to thrive in sandy loam than clay. Suitable conditions were a mean January temperature of - 4.4℃ to -2.5℃, mean April temperature of 8.8℃-10.0℃, and mean annual temperature of 9.6℃-11.0℃. Aconitum austrokoreense Koidz. was first observed in sites with a mean annual rainfall of 1,670- 1,720 mm, and a mean August rainfall of at least 350 mm. Therefore, sites with increasing rainfall of up to 390 mm were preferred. The area of potential habitats having distributive significance of 75% or higher was 202 ha, or 1.8% of the area covered in this study.