• Korean Journal of Computational Design and Engineering
• /
• v.13 no.1
• /
• pp.36-44
• /
• 2008

This paper proposes a modeling and simulation process of a panel production line (PPL) in a shipyard. The panel production line is an assembly process to produce a main panel of a flat block and a curved block. In this paper, its activity analysis is carried out using expression of IDEF0, and its process is qualitatively and quantitatively analyzed and modeled by Petri Nets. A commercial discrete event simulation tool, $QUEST^{TM}$, is used for virtual PPL and simulation. The modeling results by Petri Net are mapped to elements of the simulation tool. Finally, an integrated simulation environment of PPL is implemented in order to efficiently utilize the virtual PPL model. With the help of IDEF0 and Petri Nets, we could systematically analyze and describe the PPL process that are characterized as being concurrent, asynchronous, distributed, parallel, nondeterministic, and/or stochastic. Also, the dynamic and concurrent activities of a PPL system were able to be simulated. A timing concept can be included into the Petri nets model to evaluate performance and dependability issues of the system.

• Journal of Ocean Engineering and Technology
• /
• v.25 no.6
• /
• pp.105-109
• /
• 2011

As is well appreciated, welding is the most important fundamental process in manufacturing marine structures. However, weld-induced deformation is inevitable because of the non-uniform distribution of temperature during welding. The deformation caused by welding is one of the principal obstacles in enhancing the productivity in the manufacturing procedure for marine structures. This should be much more seriously considered in the case of the thin blocks found in a ship with multi-deck structures. This paper is concerned with the deformation control of thin panel blocks by applying intermittent welding to fillet welding. In order to investigate the quantitative effect of the intermittent welding, a thermo elasto-plastic analysis was carried out with various welding pitches and plate thicknesses. Welding tests were also carried out to show the validity of the present thermo-elasto-plastic analysis. Numerical analysis results showed good agreement with those of the welding tests. As far as the present numerical results are concerned, it has been seen that a more than 50% reduction in angular distortion can be achieved by applying the intermittent welding because of the low heat input.

• Journal of the Korea Convergence Society
• /
• v.8 no.10
• /
• pp.185-191
• /
• 2017

Recently, for such reasons as its inexpensive price and eco-friendliness, LNG has been under the limelight as an alternative fuel for vessels and is expected to grow rapidly in the industry. However, the technology level of domestic shipbuilders in manufacturing the cryogenic pump designed to supply LNG for vessels is so low that design and manufacturing technology of core parts are in urgent need. Therefore, this study describes the stepwise development procedure of cryogenic submerged centrifugal pump for ship LNG supply system. And it aims to suggest practical and specific development methods of the pump by approaching the characteristics of each step and major development items from the standpoint of engineering and management.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.12 no.1
• /
• pp.116-128
• /
• 2020

In the shipbuilding industry, three-dimensional (3D) templates play a key role in the completeness evaluation of shell plates with a large curvature in the shell-plate fabrication process. Currently, the information of 3D templates from a ship computer-aided design system is limited; thus, manufacturers depend on their experience to produce the templates manually. This results in the inaccuracy of templates in addition to increased production time. Therefore, if the pieces of the 3D templates can be produced automatically with accurate information, the lead time of the fabrication process can be reduced. In this study, we define a new type of template piece and develop methods for extending a boundary template and converting manufacturing information into numerical control machine input. In addition, based on the results of the study, we propose a production automation system for 3D template pieces. This system is expected to reduce the lead time of the fabrication process.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.2
• /
• pp.123-130
• /
• 2016

With the development of fast construction mode in shipbuilding market, the demand on accuracy management of hull is becoming higher and higher in shipbuilding industry. In order to enhance production efficiency and reduce manufacturing cycle time in shipbuilding industry, it is important for shipyards to have the accuracy of ship components evaluated efficiently during the whole manufacturing cycle time. In accurate shipbuilding process, block accuracy is the key part, which has significant meaning in shortening the period of shipbuilding process, decreasing cost and improving the quality of ship. The key of block accuracy control is to create a integrate block accuracy controlling system, which makes great sense in implementing comprehensive accuracy controlling, increasing block accuracy, standardization of proceeding of accuracy controlling, realizing "zero-defect transferring" and advancing non-allowance shipbuilding. Generally, managers of accuracy control measure the vital points at section surface of block by using the heavy total station, which is inconvenient and time-consuming for measurement of vital points. In this paper, a new measurement method based on point clouds technique has been proposed. This method is to measure the 3D coordinates values of vital points at section surface of block by using 3D scanner, and then compare the measured point with design point based on ICP algorithm which has an allowable error check process that makes sure that whether or not the error between design point and measured point is within the margin of error.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.5
• /
• pp.542-550
• /
• 2007

A geometry modification is one of main keys in achieving a successful optimization. The optimized hull form generated from the geometry modification should be a realistic, faired form from the ship manufacturing point of view. This paper presents a practical hull optimization procedure using a parametric modification function. In the parametric modification function method, the initial ship geometry was easily deformed according to the variations of design parameters. For example, bulbous bow can be modified with several parameters such as bulb area, bulb length, bulb height etc. Design parameters are considered as design variables to modify hull form, which can reduce the number of design variables in optimization process and hence reduce its time cost. To verify the use of the parametric modification function, optimization for KCS was performed at its design speed (FN=0.26) and the wave making resistance is calculated using a well proven potential code with fully nonlinear free surface conditions. The design variables used are key design parameters such as Cp curve, section shape and bulb shape. This study shows that the hull form optimized by the parametric modification function brings 7.6% reduction in wave making resistance. In addition, for verification and comparison purpose, a direct geometry variation method using a bell-shape modification function is used. It is shown that the optimal hull form generated by the bell-shaped modification function is very similar to that produced by the parametric modification function. However, the total running time of the parametric optimization is six times shorter than that of the bell shape modification method, showing the effectiveness and practicalness from a designer point of view in ship yards.

• IE interfaces
• /
• v.6 no.1
• /
• pp.99-112
• /
• 1993

This study deals with analysis of material from in Tube manufacturing line. This line is a multi product flow ship type production line, which consists of 5 steps of work station. Some work stations involve in unnecessary moving activities of workers and much work in-process storage due to the non-systematic material flow with respect to the different lot size production of multi-items. To improve productivity for this line, one alternative is considered such as grouping two work stations by using GT and JIT concepts. Also, feasibility analysis for this alternative is performed using and simulation model built by SIMAN IV simulation language.

• Proceedings of the Korea Society for Simulation Conference
• /
• 1998.10a
• /
• pp.65-65
• /
• 1998

Manufacturing systems like a motor production process are analyzed using simulations than numerical analyses and/or heuristic methods due to their stochastic properties. The SME(small and medium enterprise) producing automotive motors that develop CIM systems to improve production performance is focused as an application site. We analyze and understand the system exactly using layout based simulation, and then we will suggest the initial feashible production-plan dependent on the layout to overcome weak-points of the current system(i.e., high WIPs, bottle-neck processes, due-date delays and etc.). And, solutions are suggested to increase performances of SMEs producing automotive motors in this paper. The simulation model built in this study is moedlled and analyzed with fully object-oriented methodology using SiMPLE++TM according to properties of production processes of the automotive motor. And, we will introduce ways to verify the model with developed templates for reusability when new needs will be occurred such as designing a new ship, extension or rearrangement of the system, change of production-plans, receiving urgent orders, and so on.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.5
• /
• pp.89-94
• /
• 2008

Marine propeller is one of the most important element of ship, it must be taken care of design and maintenance of it. It is inevitable that corrosion pits have occurred on the marine propeller. If corrosion pits have occurred on the blades, they have been repaired ordinary by simple welding methods in shipyards. It must be that the strength is degraded in this process. In this paper, we represent the improvement method of fatigue strength degraded after repairing pits.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.51-51
• /
• 2010

Recently just as in the automobile industry, shipbuilders also try to reduce material consumption and weight in order to keep operating costs as low as possible and improve the speed of production. Naturally industry is ever searching for welding techniques offering higher power, higher productivity and a better quality. Therefore it is important to have a details research based on the various welding process applied to steel and other materials, and to have the ability both to counsel interested companies and to evaluate the feasibility of implementation of this process. Submerged-arc welding (SAW) process is usually used about 20% of shipbuilding. Similar to gas metal arc welding(GMAW), SAW involves formation of an arc between a continuously-fed bare wire electrode and the work-piece. The process uses a flux to generate protective gases and slag, and to add alloying elements to the weld pool and a shielding gas is not required. Prior to welding, a thin layer of flux powder is placed on the work-piece surface. The arc moves along the joint line and as it does so, excess flux is recycled via a hopper. Remaining fused slag layers can be easily removed after welding. As the arc is completely covered by the flux layer, heat loss is extremely low. This produces a thermal efficiency as high as 60% (compared with 25% for manual metal arc). SAW process offers many advantages compared to conventional CO2 welding process. The main advantages of SAW are higher welding speed, facility of workers, less deformation and better than bead shape & strength of welded joint because there is no visible arc light, welding is spatter-free, fully-mechanized or automatic process, high travel speed, and depth of penetration and chemical composition of the deposited weld metal. However it is difficult to application of thin plate according to high heat input. So this paper has been focused on application of the field according to SAW process for thin plate in ship-structures. For this purpose, It has been decided to optimized welding condition by experiments, relationship between welding parameters and bead shapes, mechanical test such as tensile and bending. Also finite element(FE) based numerical comparison of thermal history and welding residual stress in A-grade 3.2 thickness steel of SAW been made in this study. From the result of this study, It makes substantial saving of time and manufacturing cost and raises the quality of product.