• Journal of Radiation Protection and Research
• /
• 제40권2호
• /
• pp.118-123
• /
• 2015

최근 의료기관에서의 진단방사선검사 빈도는 2011년 2억 2천만건, 연간 일인당 피폭선량은 1.4 mSv로 2007년 대비 각 51%, 35% 증가하였다. 여기서 흉부촬영건수는 일반촬영 중 가장 높은 빈도인 27.59%로 나타났다. 따라서 본 연구에서는 흉부 방사선 촬영 시 영상판독에 불필요한 신체부위를 차폐하여 피폭선량을 최소화 시키는 차폐기구를 개발하고, 그 유용성 평가를 위해 국제 표준 소아(10세) 팬텀과 유리선량계를 사용하여 기구 사용 전, 후의 입사표면선량(entrance surface dose; ESD)과 장기의 흡수선량 차를 측정하였다. 또한 몬테카를로 시뮬레이션 기반 프로그램(PCXMC 2.0.1)을 이용하여 유효선량을 산출하였고 암발생의 생애귀속위험도(lifetime attributable risk of cancer incidence; LAR)를 비교하여 그 감소율을 간접적으로 평가하였다. 방어기구를 사용할 때, 입사표면선량(감소율)은 비강 $0.55{\mu}Sv$ (74.06%), 갑상선 $1.43{\mu}Sv$ (95.15%), 식도 $6.35{\mu}Sv$ (78.42%)로 평균 86.36% 감소되었고, 심부선량(감소율)은 경추 $1.23{\mu}Sv$ (89.73%), 침샘 $0.5{\mu}Sv$ (92.31%), 식도 $3.85{\mu}Sv$ (59.39%), 갑상선 $2.02{\mu}Sv$ (73.53%) 흉추 $5.68{\mu}Sv$ (54.01%) 로 평균 72.30%로 감소되어 차폐기구의 유용성을 확인할 수 있었다. 또한, 유효선량은 착용 전 $8.33{\mu}Sv$에서 착용 후 $7.35{\mu}Sv$로 11.76% 감소하였고, LAR 평가에서는 갑상선 암은 10세 소아 백만 명당 남아 0.14명(95.12%), 여아 0.77명(95.16%), 모든 암은 남아 0.14명(11.70%), 여아 0.25명(11.70%)의 감소(감소율)를 확인할 수 있었다. 진단방사선검사는 질병과 치료 등 건강을 위해 꼭 필요한 검사이지만, 가능한 진단에 불필요한 부위에 이러한 차폐기구를 적극적으로 사용하여 ALARA 개념에 입각한 의료방사선 최적화를 도모해야 할 것이다.

• 융합신호처리학회논문지
• /
• 제25권2호
• /
• pp.52-57
• /
• 2024

난류 경계층 내부 와류 구조물 형상을 측정하기 위해 열선 유속계(Hot-wire sensor)를 스테퍼 모터 컨트롤러(Stepper motor controller)에 고정하여 측정 지점으로 이동시켰다. 유동장 내 표면 근처 유속은 상대적으로 느려 차후 측정 데이터 해석 시 신호처리 과정에서 전자파 간섭으로 민감하게 반응하게 된다. 전자파 잡음은 주로 컴퓨터나 기타 전자 장비의 전원 공급에서 발생하는데, 실험 장비 중 전원이 활성화된 스테퍼 모터(Stepper motor)에서 전자파 잡음이 열선 유속계와 연결된 BNC 케이블로 유입되었다. 이는 열선 유속계를 이동시키기 위해 모터 컨트롤러(Motor controller)에 전원 공급이 인가되면, 오실로스코프 화면에 전자파 잡음이 나타나는 것을 확인하였다. 열선 유속계에서 측정된 데이터에 예상치 못한 잡음이 포함될 가능성이 있으므로, 이를 감소시키고 측정 과정에서 신호대 잡음비(Signal-to -Noise Ratio, SNR)를 향상하도록 연결 케이블을 차폐시키고 전자파가 차단되는 컴퓨터로 교체하였다.

• 대한방사선기술학회지:방사선기술과학
• /
• 제38권3호
• /
• pp.205-211
• /
• 2015

복부 전후 방향 검사 시 automatic exposure control (AEC) mode에서 조사시간을 제한하지 않고 검사를 하는 방법 (non-time limit, NTL) 과 조사시간을 제한하고 검사하는 방법 (time limit, TL)에 대해서 영상 품질 평가인 신호 대 잡음비 (signal to noise ratio, SNR), 대조도 대 잡음비 (contrast to ratio, CNR)를 측정하여 TL 방법과 NTL방법을 비교 평가하고자 하였다. 실험 기기는 XGEO GC 80 (Samsung, Korea), Unfors ThinX RAD (Unfors, Sweden), Rando Phantom (alderson research laboratories, USA)과 $5.5{\times}9{\times}0.1cm^3$ 크기의 차폐재를 사용하였으며, AEC mode에서 전리함 (ionization chamber)를 상단 2 개만 작동하도록 설정하고 관전압은 80 kVp로 설정하였다. TL 방법의 경우에는 조사시간을 51 msec로 제한하였으며, 전리함에 차폐재를 부착하지 않은 상태와 부착한 상태에서 NTL AEC mode와 TL AEC mode의 영상을 획득하였다. 또한 'Image J"를 이용하여 영상 평가방법인 SNR과 CNR로 평가하였다. 결론적으로 차폐재를 부착했을 때 NTL AEC mode가 다른 실험 방법보다 선량이 최대 130.7% 최소 80%까지 증가한 결과 값을 보였으며, TL AEC mode는 NTL AEC mode보다 mAs와 피폭선량에서 각 각 43.8%, 44.4% 감소한 값을 보였다. 통계적으로는 SNR과 CNR은 유의한 차이를 보이지 않았다($p{\geq}0.05$). 그러므로, 본 연구에서는 BMI 지수가 높은 환자나 수술 후 인체 내에 금속물질이 있는 환자를 검사할 경우에는 TL AEC mode가 유효한 검사법이라고 사료된다.

• 전기학회논문지
• /
• 제59권4호
• /
• pp.728-732
• /
• 2010

GIS(Gas insulated switching gear) is power equipment with excellent dielectric strength and is economy merit in high confidence and stability. Recently, because equipment of GIS was occurring problem of confidence used for a long time, partial discharge on-line diagnosis systems have been importantly recognized. Partial discharge (PD) detection is an effective means for monitoring and evaluation of dielectric condition of gas insulated system (GIS). The ultra-high-frequency (UHF) PD detection technique can detect and locate the PD sources inside GIS by detecting electromagnetic wave emitted from PD source. Therefore, real-time diagnostic system using UHF detection method has been developed for this application is being expanded gradually. However, the signal of partial discharge occurring in SF6 gas is very weak and susceptible to external noises which mainly consist of PD in air. Thus, it is important to distinguish the PD in SF6 gas more sensitively from the external noises. Unfortunately, these external noise signals and the partial discharge signals have very similar characteristics. Therefore, to solve this problem, we need the signal processing method for distinguish partial discharge signals with external noise signals for improvement of SNR(signal to noise ratio) and sensitivity. In this paper, we proposed internal signal processing method for removing external noise signals with built-in pre.amplifier and frequency conversion circuit.

• 한국정밀공학회지
• /
• 제23권3호
• /
• pp.47-55
• /
• 2006

Laser welding of dissimilar metals has been widely used to improve a wear resistance and a corrosion resistance of the industrial parts. The objective of this research is to investigate the influence of the process parameters, such as the welding for SM45C and STS304 with CW Nd:YAG lasers. The bead-on-plate welding tests are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the dissimilar welding, the welding quality of the cut section, stress-strain behavior and the hardness of the welded metal are investigated. From the results of the investigation, it has been shown that the optimal voiding condition without defects in the vicinity of the welded area and with a good welding quality is 1600W of the laser power, 0.85m/min of welding speed and $4{\ell}/min$ of pressure for shielding gas.

• Wind and Structures
• /
• 제3권3호
• /
• pp.177-191
• /
• 2000

This paper presents an approach for evaluating directionality effects for both wind speeds and wind loads in hurricane-prone regions. The focus of this study is on directional wind loads on low-rise structures. Using event-based simulation, hurricane directionality effects are determined for an open-terrain condition at various locations in the southeastern United States. The wind speed (or wind load) directionality factor, defined as the ratio of the N-year mean recurrence interval (MRI) wind speed (or wind load) in each direction to the non-directional N-year MRI wind speed (or wind load), is less than one but increases toward unity with increasing MRI. Thus, the degree of conservatism that results from neglecting directionality effects decreases with increasing MRI. It may be desirable to account for local exposure effects (siting effects such as shielding, orientation, etc.) in design. To account for these effects in a directionality adjustment, the factor described above for open terrain would need to be transformed to other terrains/exposures. A "local" directionality factor, therefore, must effectively combine these two adjustments (event directionality and siting or local exposure directionality). By also considering the direction-specific aerodynamic coefficient, a direction-dependent wind load can be evaluated. While the data necessary to make predictions of directional wind loads may not routinely be available in the case of low-rise structures, the concept is discussed and illustrated in this paper.

• 한국결정성장학회지
• /
• 제19권5호
• /
• pp.215-222
• /
• 2009

Many concepts of external magnetic field applications in crystal growth processes have been developed to control melt convection, impurity content and growing interface shape. Especially, travelling magnetic fields (TMF) are of certain advantages. However, strong shielding effects appear when the TMF coils are placed outside the growth vessel. To achieve a solution of industrial relevance within the framework of the $KRISTMAG^{(R)}$ project inner heater-magnet modules(HMM) for simultaneous generation of temperature and magnetic field have been developed. At the same time, as the temperature is controlled as usual, e.g. by DC, the characteristics of the magnetic field can be adjusted via frequency, phase shift of the alternating current (AC) and by changing the amplitude via the AC/DC ratio. Global modelling and dummy measurements were used to optimize and validate the HMM configuration and process parameters. GaAs and Ge single crystals with improved parameters were grown in HMM-equipped industrial liquid encapsulated Czochralski (LEC) puller and commercial vertical gradient freeze (VGF) furnace, respectively. The vapour pressure controlled Czochralski (VCz) variant without boric oxide encapsulation was used to study the movement of floating particles by the TMF-driven vortices.

• 한국공작기계학회논문집
• /
• 제15권2호
• /
• pp.51-58
• /
• 2006

Laser welding of dissimilar metals has been widely used to improve a wear resistance and a corrosion resistance of the industrial parts. The objective of this research works is to investigate the influence of the process parameters, such as the welding for SM45C and STS304 with CW Nd:YAG lasers. The bead-on-plate welding tests are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the dissimilar welding, the welding quality of the cut section, stain-stress behavior and the hardness of the welded part are investigated. From the results of the investigation, it has been shown that the optimal welding condition without defects in the vicinity of the welded area and with a good welding qualify is 1600W of the laser power, 0.85m/min of welding speed and $4{\ell}/min$ of pressure for shielding gas.

• 한국멀티미디어학회논문지
• /
• 제18권3호
• /
• pp.401-407
• /
• 2015

In this paper, we propose the method to eliminate EMI (Electro-Magnetic Interference) in ELF (Extremely Low Frequency) band below 2 KHz for extending the gesture-recognition distance of smart TVs to more than 3m using electric potential sensor. First, we measure the electric field generated from the back panel of a TV and propose the effective arrangement of two sets of differential sensors as well as the shielding method using metal fiber. Also, we eliminate the PLN (Power Line Noise) and other noise generated from the TV and sensors as well as surrounding environments using filters. Using the proposed EMI eliminating methods, we evaluate displacement ratio on measured signals according to distance between sensors and a moving hand. Experiment results show that our proposed method can extend the hand-gesture sensing distance using EPS (Electric Potential Sensor) up to more than 3m, which is enough to satisfy applicability of EPS based remote control to Smart TVs.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.17-18
• /
• 2006

Laser welding of metals has been widely used to improve a wear resistance and a corrosion resistance of the industrial parts. The objective of this research works is to investigate the influence of the process parameters, such as the welding for metals with CW Nd:YAG lasers. The bead-on-plate welding tests are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the butt welding, the welding quality of the cut section, stain-stress behavior and the hardness of the welded part are investigated. From the results of the investigation, it has been shown that the optimal welding condition without defects in the vicinity of the welded area and with a good welding quality is 1400W of the laser power, 0.8m/min, 0.9m/min of welding speed and $4{\ell}$ in of pressure for shielding gas.