• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.12
• /
• pp.561-566
• /
• 2005

This paper describes electrical resistivity, dielectric strength, thermal conductivity, thermal stability and tensile strength of mica sheet impregnated with silicone rubber resin or silicone rubber resin containing alumina powder. The mica sheet impregnated with silicone rubber resin had higher electrical resistivity, dielectric strength and tensile strength than those of virgin mica sheet. Electrical resistivity of mica sheet impregnated with silicone rubber resin containing alumina increased with increasing the amount of alumina. However, dielectric strength and tensile strength of mica sheet impregnated with silicone rubber resin containing alumina decreased with increasing the amount of alumina. The mica sheet impregnated with silicone rubber resin had lower thermal conductivity than that of virgin mica sheet. However, thermal conductivity of mica sheet impregnated with silicone rubber resin conatining alumina increased with increasing the amount of alumina. In the case of thermal stability, thermal degradation of virgin mica sheet and impregnated mica sheet with silicone rubber resin did not occur up to $1100^{\circ}C$ and $400^{\circ}C$, respectively.

• Journal of the Korean Ceramic Society
• /
• v.25 no.6
• /
• pp.623-630
• /
• 1988

As a function of the composition and content of frit, the electrical property of Ag and Ag/Pd thick film conductors were investigated with microstructure. With increasing sintering temperature in Ag-frit thick film conductors, electrical sheet resistivity decreased, but again increased above 80$0^{\circ}C$. And when frit contents is 5wt%, compact and homogenious microstructure can be obtained, then electrical sheet resistivity has minimum value. In Ag/Pd-frit film conductor, the electrical sheet resistivity decreased with increasing sintering temperature. The system which having frit with low softing point has lower sheet resistivity then to add high softening point frit.

• Journal of the Korean Ceramic Society
• /
• v.13 no.2
• /
• pp.8-16
• /
• 1976

The conductive transparent film is prepared by spraying thin salt solution. In stannic chloride solution as a base solution, various dopants such as Al, Co, Cu and Ni were dissolved respectively as a chloride state and then the films were made by spraying solutions on hot glass plates. The properties of them were compared with those of the stannic salt single component film. The films doped with copper oxide and nickle oxide were improved by decreasing their sheet resistivity and temperature coefficient of resistivity. In comparison with the sheet resistivity and temperature coefficient of resistivity of stannic oxide single component film, being 2.5 K ohm/$\textrm{cm}^2$ and -1650ppm/$^{\circ}C$ respectively, its values of the film containing 15 mol % of copper oxide and formed at 40$0^{\circ}C$ were 2.5K ohm/$\textrm{cm}^2$ and -920ppm/$^{\circ}C$ respectively. The film containing 15 mol % of nickel oxide and formed at 50$0^{\circ}C$ has shown its sheet resistivity and temperature coefficient 0.7 K ohm/$\textrm{cm}^2$ and -940ppm/$^{\circ}C$ respectively.

• Electrical & Electronic Materials
• /
• v.8 no.2
• /
• pp.196-203
• /
• 1995

We presented Tungsten and Tungsten Nitride thin films deposited by RF and DC sputtering. It deposited at various conditions that determining the resistivity and sheet resistivity by stabilizing the basic theory. We investigated properties of the resistivity and sheet resistivity of these films under various conditions, temperature of substrate, flow rate of the argon gas and content of nitrogen from nitrogen-argon mixtures. As the temperature of substrate increased and the flow rate of the argon gas decreased, the resistivities of these films reduced by structural transformation. We found that these resistivities were depend on the temperature of substrate, flow rate and electric power. Very highly resistive tungsten films obtained at 10W RF power. On the contrary, we found that films deposited by DC sputtering, from which very lowly resistive tungsten films were obtained. Tungsten nitride thin films deposited by reactive DC sputtering and the resistivities of these films increased as the content of nitrogen gas increased from nitrogen-argon mixture. And also we found the results show very good agreement, compared with experimental data.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.160-163
• /
• 1994

Tungsten and Tungsten Nitride thin films deposited by RF and DC sputtering and the resistivity of these films was measured. We deposited tungsten and tungsten nitride films by RF and DC sputtering at various conditions and derived equations that determines the resistivity and sheet resistivity by stabilizing the basic theory. We investigated properties of the resistivity and sheet resistivity of theme films under various conditions like temperature of substrate, flow rate of the argon gas and content of nitrogen from nitrogen-argon mixtures

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.8
• /
• pp.1559-1565
• /
• 2009

Resistivity changes and intermetallic growth after thermal aging of Matter tin-plated copper sheet for current collector in fuel cell were investigated to survey the diffusion of Cu into Sn in interface and surface. The results show that the intermetallic growth and resistivity depended on thermal aging temperature and dwell time. In Sn plate on a Cu substrate, Cu6Sn5(${\mu}$) and Cu3Sn(${\varepsilon}$) intermetallics layer were formed at plate/substrate interface. Cu6Sn5(${\mu}$) intermetallics layer gradually changed Cu3Sn(${\varepsilon}$). Moreover Cu get through Sn layer and it was diffused in the surface at $200^{\circ}C$. On the other hand, only Cu3Sn(${\varepsilon}$) intermetallics layer were formed at plate/substrate interface at $300^{\circ}C$. Consequently, the intermetallics formation, thermal condition and oxidation of surface, causes increase in the resistivity of Tin-plated copper sheet.

• Electrical & Electronic Materials
• /
• v.9 no.9
• /
• pp.911-917
• /
• 1996

Platinum thin films were deposited on Si-wafer by DC rnagnetron sputtering for RTD (resistance thermometer devices). We investigated the physical and electrical characteristics of these films under various conditions, the input power, working vacuum, temperature of substrate and also after annealing these films. The deposition rate was increased with increasing the input power but decreased with increasing Ar gas pressure. The resistivity and sheet resistivity were decreased with increasing the temperature of substrate and the annealing time at 1000.deg. C. At substrate temperature of >$300^{\circ}C$, input power of 7 w/cm$^{2}$, working vacuum of 5 mtorr and annealing conditions of 1000.deg. C and 240 min, we obtained 10.65.mu..ohm..cm, resistivity of Pt thin films and 3800-3900 ppm/.deg. C, TCR(temperature coefficient of resistance). These values are close to the bulk value. These results indicate that the Pt thin films deposited by DC magnetron sputtering have potentiality for the development of Pt RTD temperature sensor.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.2067_2068
• /
• 2009

Resistivity changes and intermetallic growth after thermal aging of Matter tin-plated copper sheet for current collector in fuel cell were investigated to survey the diffusion of Cu into Sn in interface and surface. The results show that the intermetallic growth and resistivity depended on thermal aging temperature and dwell time. In Sn plate on a Cu substrate, $Cu_6Sn_5({\mu})$ and $Cu_3Sn({\varepsilon})$ intermetallics layer were formed at plate/substrate interface. $Cu_6Sn_5({\mu})$ intermetallics layer gradually changed $Cu_3Sn({\varepsilon})$. Moreover Cu get through Sn layer and it was diffused in the surface at $200^{\circ}C$. On the other hand, only $Cu_3Sn({\varepsilon})$ intermetallics layer were formed at plate/substrate interface at $300^{\circ}C$. Consequently, the intermetallics formation, thermal condition and oxidation of surface, causes increase in the resistivity of Tin-plated copper sheet.

• Journal of the Korean Ceramic Society
• /
• v.27 no.3
• /
• pp.337-344
• /
• 1990

As a function of sintering temperature and time, the electrical properties of ruthenium based thick film resistors were investigated with microstructure. The variatio of resistivity and TCR(temperature coefficient of resistance)trends of sintered speciman at various sintering temperature were different low resistivity paste(Du Pont 1721) from high one(Du Pont 1741). These phenomena are deeply relative to microstructure of sintered film. With increasing the sintering temperature for 1721 system, the electrical sheet resistivity decreased, but again gradually increased above 80$0^{\circ}C$. And TCR trends in 1721 system are all positive. On the other hand the electrical sheet resistivity of 1741 resistor system decreased with sintering temperature. And TCR trends variable according to sintering temperature. TCR of speciman sintered at $700^{\circ}C$ was negative value, and TCR of 80$0^{\circ}C$ sintered speciman coexisted negative and positive value. But in case of speciman sintered at 90$0^{\circ}C$, TCR was positive value. As results of this fact, it was well known that the charge carrier contributied to electrical conduction in 1741 resistor system varied with sintering temperature.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.4
• /
• pp.187-191
• /
• 2004

In this work, we used the PCID simulator for simulation of solar cell and examined the effect of front-back surface recombination velocity, minority carrier diffusion length, junction depth and emitter sheet-resistance. As the effect of base thickness, the efficiency decreased by the increase in series resistance with the increase of the thickness and found decrease in efficiency by decrease of the current as the effect of the recombination. Also, as the effect of base resistivity, the efficiency increased somewhat with the decrease in resistivity, but when the resistivity exceeded certain value, the efficiency decreased as a increase in the recombination ratio. The optimum efficiency was obtained at the resistivity 0.5 $\Omega$-cm, and thickness $100\mu\textrm{m}$. We have successfully achieved 10.8% and 13.7% efficiency large area($103mm{\times}103mm$) mono-crystalline silicon solar cells without and with PECVD silicon nitride antireflection coating.