• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.4
• /
• pp.321-327
• /
• 2007

In lock-in thermography, a phase difference between the defect area and the healthy area indicates the qualitative location and size of the defect. To accurately estimate these parameters, the shearing-phase technique has been employed which gives the shearing-phase distribution. The shearing-phase distribution has maximum, minimum, and zero points that help determine quantitatively the size and location of the subsurface defect. In experiment, the proposed technique is verified with artificial specimen and these related factors are analyzed.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.2
• /
• pp.91-97
• /
• 2010

This paper proposes method to evaluate the location and size of the internal defects of metallic specimens by the shearing phase lock-in infrared thermography. Until now, infrared thermography test for metal specimen of STS304 and Cu-Zn were conducted to find the best test conditions. However, In unspecified situation of the form and existence of defects, there was a disadvantage to takes a long time for finding the optimal experimental conditions. The defect detection and evaluation was performed at 60 MHz signal using lock-in and shearing-phase method under limited heating conditions. By shearing-phase distribution method, Defects for the maximum, minimum and zero points were quantitatively detected at the size and location of the subsurface. As results, application of the proposed technique was verified for STS304 and Cu7-Zn3 with artificial defect and factors affected defect evaluation were searched and analyzed.

• Journal of Mechanical Science and Technology
• /
• v.15 no.12
• /
• pp.1845-1852
• /
• 2001

This paper deals with the experiment to obtain quantitative information about conditions of the interface between a water drop and surrounding oil. Velocity distributions in very close region of the interface are measured by introducing a new illumination technique and a telecentric lens. It enables precise measurements of velocity distributions in the close region to the interface. Although the measured velocity distributions exhibit strong influence from the solid wall of an experimental tube, the coincidence of inner and outside velocities on the interface is clearly confirmed for the clean interface. The shearing stresses on the interface, which are proportional to the velocity gradient normal to the interface, clearly show conditions of contaminated interface, which can be divided into two parts. From front stagnation point to somewhere near a separation point, the distribution of shearing stresses is well coincide with that of the Hadamard's analytical solution, while the distribution on the latter part of the interface sows quite different feature, which is supposed to be strongly influenced by contamination of the surface.

• Korean Journal of Optics and Photonics
• /
• v.16 no.3
• /
• pp.239-247
• /
• 2005

In this study, we have used newly developed dual-beam shearography which is based on laser speckle that includes various information about an object. Among the several shearing techniques, we used Michelson shearing interference technique which is the most powerful. Acrylate plate was used as a sample, which has inner defects and low thermal conductivity. Michelson shearing interferometer was used for obtaining speckle fringes. We also used phase shifting technique to get a phase map. Using single beam illumination, we could obtain mixture of deformation components of both in-plane and out-of-plane. In order to separate the two components, we have used dual-beam shearography technique. We have obtained a speckle pattern of both before and after deformation. Through LS filtering and unwrapping processes, we could find a position and a shape of the inner defects easily. Deformation of the acrylate plate due to thermal heating has occurred mainly in z-direction(out-of-plane) because it has low thermal conductivity. The acrylate plate was deformed only at the restricted area where the electrical heat applied.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.1
• /
• pp.23-29
• /
• 2008

Two high resolution compressive schemes, CICSAM(Ubbink, 1997) and HRIC(Muzaferija & Peric, 1999), in interface capturing method are reviewed briefly with respect to the extended forms suitable for unstructured meshes. And then those are applied to three typical test cases of translation test, shearing flow test and collapsing water problem with an obstacle. It is accomplished by implementing the high resolution schemes in the in-house CFD code(PowerCFD) for computing 3-D flow with an unstructured cell-centered method, which is based on the finite-volume technique and fully conservative. The calculated results show that CICSAM is better than HRIC with respect to accuracy and robustness, although either scheme can be used as a good choice for free surface or two-phase flow simulation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.432-438
• /
• 1994

This paper describes the measuring method of vibration mode shapes by the Electronic Shearography. Shearographic interferometer has many merits in practical use, that is low sensitive to the environmental noisy, liw limit of the coherent-length and simple optical configuration etc.. In this study, we developed Michelson-type shearing interferometer provided with a phase stepping mirror and with a bias modulation mirror to quantify the vibration gradient fields. As a results of application to a simple cantilever plate vibration amplitude fields were obtained by the proper integration technique, and their exprimental results were in good agreement with those of the ESPI experiment.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.2
• /
• pp.104-109
• /
• 2010

Lap joint friction stir welding(LFSW) is an relatively new solid state joining process. A6061-T6 aluminium alloy has gathered wide acceptance in the fabrication of light weight structures requiring a high strength to weight ratio and good corrosion resistance. Test methods used in this paper, lock-in thermography, a phase difference between the defect area and the healthy area indicates the qualitative location and size of the defect. In this paper, the defects detected from the thermal image of mechanical properties for weld were evaluated and compared by the lock-in infrared thermography technique.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.1
• /
• pp.48-55
• /
• 2012

Pressure vessels in vehicle industries, power plants, and chemical industries are often affected by flaw and defect generated inside the pressure vessels due to production processes or being used. It is very important to detect such internal defects of pressure vessel because they sometimes bring out serious problems. In this paper, an optical defect detection method using digital shearography is used. This method has advantages that the inspection can be performed at a real time measurement and is less sensitive to environmental noise. Shearography is a laser-based technique for full-field, non-contacting measurement of surface deformation (displacement or strain). The ultimate goal of this paper is to detect flaws in pressure vessels and to measure the lengths of the flaws by using unwrapping, phase images which are only obtained by Phase map. Through this method, we could decrease post-processing (next processing). Real length of a pixel can be calculated by comparing minimum and maximum unwrapping images with shearing angle. Through measuring several specimen defects which have different lengths and depths of defect, it can be possible to interpret quantitatively by calculating gray level.