• Transactions of Materials Processing
• /
• v.23 no.8
• /
• pp.501-506
• /
• 2014

Progressive shearing with blanking dies is commonly employed to produce large quantities of tiny sheet metal electronic parts. Sheet metal pins, which are narrow and long, that are sheared with a progressive die set are often twisted. The twist in the sheet metal pins, which usually occurs in the final shearing operation, generally decreases with increasing blank holding force. The blank holding forces in all shearing operations are not the same because of different shearing positions and areas. In the current study, the optimal layout of the springs in a progressive die set to minimize the twist of the sheet metal pin is proposed. In order to find the holding force acting on the tiny narrow blanks produced with the proposed springs during the shearing process, the equivalent area method is used in the structural analysis. The shearing of the sheet-metal pin was simulated to compute the twist angle associated with the blank holding force. The constraint condition satisfying the pre-set blank holding force from the previous shearing operations was imposed. A design of experiments (DOE) was numerically implemented by analyzing the progressive die structure and by simulating the shearing process. From the meta-model created from the experimental results and by using a quadratic response surface method (PQRSM), the optimal layout of the springs was determined. The twist of sheet metal pin associated with the optimal layout of the springs found in the current study was compared with that of an existing progressive die to obtain a minimal amount of twist.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.157-171
• /
• 2009

A 151 storey super high-rise building located in an area of reclaimed land constructed over soft marine clay in Songdo, Korea is currently under design. This paper describes the design process of the foundation system of the supertall tower, which is required to support the large building vertical and lateral loads and to restrain the horizontal displacement due to wind and seismic forces. The behaviour of the foundation system due to these loads and foundation stiffness influence the design of the building super structure, displacement of the tower, as well as the raft foundation design. Therefore, the design takes in account the interactions between soil, foundation and super structure, so as to achieve a safe and efficient building performance. The site lies entirely within an area of reclamation underlain by up to 20m of soft to firm marine silty clay, which overlies residual soil and a profile of weathered rock. The nature of the foundation rock materials are highly complex and are interpreted as possible roof pendant metamorphic rocks, which within about 50m from the surface have been affected by weathering which has reduced their strength. The presence of closely spaced joints, sheared and crushed zones within the rock has resulted in deeper areas of weathering of over 80m present within the building footprint. The foundation design process described includes the initial stages of geotechnical site characterization using the results of investigation boreholes and geotechnical parameter selection, and a series of detailed two- and three-dimensional numerical analysis for the Tower foundation comprising over 172 bored piles of varying length. The effect of the overall foundation stiffness and rotation under wind and seismic load is also discussed since the foundation rotation has a direct impact on the overall displacement of the tower.

• Water for future
• /
• v.14 no.4
• /
• pp.73-81
• /
• 1981

More than 650 numbers of water well ranging in depth from 100M to 200M were installed in South Korean Penninsula during the last decade for the purpose of industrial use and municipal water supply. Those data were compiled and synthesized by writer to determine their hydrogeologic occurences in accordance with their geologic and areal characteristics. Rocks yielding the deep seated ground water beared in the geologic primary and secondary porosities are classified into 6 groups according to their geologic, hydrogeologic, and topographic characteristics, that are: volcanic, sedimentary, meta-sediment and/or schist, andesitic, gneissic, and granitic rocks. The order of ground water productivity of the groups is as written above. Even granitic rocks including porphyries, granite, and intermediate and basic plutonic rocks is considered to be the most poorest ground water yielding group among 6, it's average yield form a single well with average drilling depth of 116M is about 225 cubic meters per day if it's drilling site is properly located. Generally speaking, seizable geologic structures such as fractured, sheared, and faulted zone at the flat surface and valley center yield almost 310% more of deep seated bet rock ground water in comparision with minor structures of joints, bedding planes, and so on that are occured at high land. 50 numbers of water well drilled at crystalline rocks were specially checked and measured it's ground water yie 1ds at each drilled depth to determine each interval's productivity while hammer drilling was going on. The results indicate that the specific capacity and yield of each water well at a depth below 70M to 80M was almost neglegible. It means that optimum well depth of crystalline rocks, except the area having seizable geologic structures, shall be not deeper than 80M.

• Korean Journal of Heritage: History & Science
• /
• v.42 no.1
• /
• pp.122-142
• /
• 2009

This study explored all domestic and international theories for maintenance and health enhancement of an old and big tree, and carried out the anatomical survey of the operation part of the tree toward he current status of domestic surgery and the perception survey of an expert group, and drew out following conclusion through the process of suggesting its reform plan. First, as a result of analyzing the correlation of the 67 subject trees with their ages, growth status. surroundings, it revealed that they were closely related to positional characteristic, damage size, whereas were little related to materials by fillers. Second, the size of the affected part was the most frequent at the bough sheared part under $0.09m^2$, and the hollow size by position(part) was the biggest at 'root + stem' starting from the behind of the main root and stem As a result of analyzing the correlation, the same result was elicited at the group with low correlation. Third, the problem was serious in charging the fillers (especially urethane) in the big hollow or exposed root produced at the behind of the root and stem part, or surface-processing it. The benefit by charging the hollow part was analyzed as not so much. Fourth, the surface-processing of fillers currently used (artificial bark) is mainly 'epoxy+woven fabric+cork', but it is not flexible, so it has brought forth problems of frequent cracks and cracked surface at the joint part with the treetextured part. Fifth, the correlation with the external status of the operated part was very high with the closeness, surface condition, formation of adhesive tissue and internal survey result. Sixth, the most influential thing on flushing by the wrong management of an old and big tree was banking, and a wrong pruning was the source of the ground part damage. In pruning a small bough can easily recover itself from its damage as its formation of adhesive tissue when it is cut by a standard method. Seventh, the parameters affecting the times of related business handling of an old and big tree are 'the need of the conscious reform of the manager and related business'. Eighth, a reform plan in an institutional aspect can include the arrangement of the law and organization of the old and big tree management and preservation at an institutional aspect. This study for preparing a reform plan through the status survey of the designated old and big tree, has a limit inducing a reform plan based on the status survey through individual research, and a weak point suggesting grounds by any statistical data. This can be complemented by subsequent studies.