• The Korean Journal of Ceramics
• /
• 제3권3호
• /
• pp.208-212
• /
• 1997

Shear-induced phase transformation behavior of chemically stabilized $\beta$-cristobalite was studied by the fiber push-out technique. To obtain the critical grain size for phase transformation, the hot-pressed polycrystalline $\beta$-cristobalite, which was used as the interphase between fiber and matrix, was annealed at $1300^{\circ}C$ for 10h. Two types of fibers, mullite and sapphire fiber, were used in this study. Debonding between mullite fiber and cristobalite interphase occurred at a critical load of 230 MPa. Static friction and fiber sliding were continuously followed by debonding. Shear-induced transformation induced cracks in the cristobalite interphase at the debonding stage. In the case of the sapphire fiber, the debonding occurred at a lower load of 180 MPa due to the residual stress in the interface caused by the difference in thermal expansion coefficients between the fiber and the cristobalite interphase. The load was insufficient for shear-induced phase transformation.

• The Korean Journal of Ceramics
• /
• 제3권2호
• /
• pp.116-123
• /
• 1997

A chemically stabilized $\beta$-cristobalite, which is stabilized by stuffing cations of $Ca^{2+}$ and $Al^{3+}$, was prepared by a solution-polymerization route employing Pechini resin or PVA solution as a polymeric carrier. The polymeric carrier affected the crystallization temperature, morphology of calicined powder, and particle size distribution. In case of the polyvinyl alcohol (PVA) solution process, a fine $\beta$-cristobalite powder with a narrow particle size distribution (average particle size : 0.3$\mu\textrm{m}$) and a BET specific surface area of 72 $\m^2$/g was prepared by an attrition-milling for 1 h after calcination at 110$0^{\circ}C$ for 1h. Wider particle size distribution and higher specific surface area were observed for the $\beta$-cristobalite powder derived from Pechini resin. The cubie(P1-to-tetraganalb) phase transformation in polynystalline $\beta$-cristobalite was induced at approximately 18$0^{\circ}C$. Like other materials showing transformation toughening, a critical size effect controlled the $\beta$-to-$\alpha$ transformation. Densifed cristobalite sample had some cracks in its internal texture after annealing. The cracks, occurred spontaneoulsy on cooling, were observed in the sample with an average grain sizes of 4.0 $\mu\textrm{m}$ or above. In case of the sintered cristobalite having a composition of CaO.$2Al_2O_3$.40SiO$_2$, small amount of amorphous phase and slow grain growth during annealing were observed. Shear stress-induced transformation was also observed in ground specimen. Cristobalite having a composition of CaO.2Al2O3.80SiO2 showed a more sensitive response to shear stress than the CaO.$2Al_2O_3$.40SiO$_2$ type cristobalite. Shear-induced transformation resulted in an increase of volume about 13% in $\alpha$-cristobalite phase on annealing for above 10 h in the case of the former composition.

• 한국재료학회지
• /
• 제26권6호
• /
• pp.325-331
• /
• 2016

This paper presents a study of the tensile properties of austenitic high-manganese steel specimens with different grain sizes. Although the stacking fault energy, calculated using a modified thermodynamic model, slightly decreased with increasing grain size, it was found to vary in a range of $23.4mJ/m^2$ to $27.1mJ/m^2$. Room-temperature tensile test results indicated that the yield and tensile strengths increased; the ductility also improved as the grain size decreased. The increase in the yield and tensile strengths was primarily attributed to the occurrence of mechanical twinning, as well as to the grain refinement effect. On the other hand, the improvement of the ductility is because the formation of deformation-induced martensite is suppressed in the high-manganese steel specimen with small grain size during tensile testing. The deformation-induced martensite transformation resulting from the increased grain size can be explained by the decrease in stacking fault energy or in shear stress required to generate deformation-induced martensite transformation.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.366-371
• /
• 2002

Because of the environmental problems, automotive companies are trying to reduce the weight of car body. Therefore, TRIP(TRansformation Induced Plasticity) steels, which have high strength and ductility have been developed. Welding process is a complex process; therefore deciding the optimal welding conditions on the basis of experimental data is an effective method. However, trial-and-error method to decide the optimal conditions requires too many experiments. To overcome these problems, response surface methodology was used. Response surface methodology is a collection of mathematical and statistical techniques that are used in the modeling and analysis of problems in which a response of interest is influenced by several variables and the objective is to optimize this response. This method was applied to the resistance spot welding process of the TRIP steel to optimize the welding parameters.

• International Journal of Korean Welding Society
• /
• 제2권2호
• /
• pp.47-50
• /
• 2002

Because of the environmental problems, automotive companies are trying to reduce the weight of car body. Therefore, TRIP(TRansformation Induced Plasticity) steels, which have high strength and ductility have been developed. Welding process is a complex process; therefore deciding the optimal welding conditions on the basis of experimental data is an effective method. However, trial-and-error method to decide the optimal conditions requires too many experiments. To overcome these problems, response surface methodology was used. Response surface methodology is a collection of mathematical and statistical techniques that are used in the modeling and analysis of problems in which a response of interest is influenced by several variables and the objective is to optimize this response. This method was applied to the resistance spot welding process of the TRIP steel to optimize the welding parameters.

• Journal of Welding and Joining
• /
• 제21권2호
• /
• pp.76-81
• /
• 2003

Due to the environmental problem, automotive companies are trying to reduce the weight of car body. Therefore, WP(Transformation Induced Plasticity) steels, which are hish strength and ductility have been developed. The application of TRIP steel to the members has been reported to increase the energy absorption capability. Welding process is a complex process; therefore deciding the optimal welding conditions is an effective method on the basis of the experimental data. However, using a trial-and-error method from the beginning in such a wide area, in order to decide the optimal conditions requires too many numbers of experiments. To overcome these problems and to decide the optimal conditions, response surface methodology was used. Response surface methodology is a collection of mathematical and statistical techniques that are for the modeling and analysis of problems in which a response of interest is influenced by several variables and the objective is to optimize this response. The introduced method was applied to the resistance spot welding process of the TRIP steel and the welding parameters were optimized. (Received December 6, 2002)

• Geomechanics and Engineering
• /
• 제14권1호
• /
• pp.1-8
• /
• 2018

This paper presents an investigation of the liquefaction characteristics and particle crushing of isotropically consolidated silica sand specimens at a wide range of confining pressures varying from 0.1 MPa to 5 MPa during undrained cyclic shearing. Different failure patterns of silica sand specimens subjected to undrained cyclic loading were seen at low and high pressures. The sudden change points with regard to the increasing double amplitude of axial strain with cycle number were identified, regardless of confining pressure. A higher cyclic stress ratio caused the specimen to liquefy at a relatively smaller cycle number, conversely producing a larger relative breakage $B_r$. The rise in confining pressure also resulted in the increasing relative breakage. At a specific cyclic stress ratio, the relative breakage and plastic work increased with the rise in the cyclic loading. Less particle crushing and plastic work consumption was observed for tests terminated after one cyclic loading. Majority of the particle crushing was produced and majority of the plastic work was consumed after the specimen passed through the phase transformation point and until reaching the failure state. The large amount of particle crushing resulted from the high-level strain induced by particle transformation and rotation.

• 열처리공학회지
• /
• 제3권2호
• /
• pp.1-9
• /
• 1990

Since the reverse shape memory effect(RSME) was reported in a CuZnAl alloy, further study has been done on the mechanism of this phenomenon and reported that it occurs by the bainitic transformation. But the present authors revealed in the previous work that the RSME in a B2 CuZnAl alloy is not caused by the shear process involved in the bainitic transformation and also that the RSME takes place as the remaining ${\alpha}^{\prime}{_2}$ phase, which is two-step transformed strain induced martensite, is newly transformed into ${\alpha}$ phase. In order to provide further evidence in supporting the facts, thus, more detailed investigations have been carried out in a $DO_3$ CuZnAl alloy.

• 한국재료학회지
• /
• 제5권7호
• /
• pp.858-868
• /
• 1995

다른 탄소함량을 갖는 두 Hadfield 강에서 압연에 따른 결정방위조직(Texture)과 마르텐사이트 상변태를 연구하였다(0.65wt.%, 1.35wt.%) 두 Hadfield 강의 적층결함에너지 차이가 매우 적음에도 불구하고 (약 2mJm$^{-2}$ ) 결정방위조직은 차이를 보였다. 0.65wt.% 탄소 강의 경우, 낮은 변형구간에서는 낮은 적층에너지 금속과 비슷한 결정방위조직을 보였으나 높은 변형에서는 {111}, {110}<001>과 같은 이상 결정방위조직이 나타났고, 이것은 입계 또는 일단의 전단띠에(shear bands) 형성된 $\alpha$ 마르텐사이트의 방해에 의한 것으로 생각된다. 이와는 대조적으로 1.35wt.% Hadfield강은 전변형구간에서 낮은 적층결함에너지를 갖는 금속과 비슷한 결정방위조직을 보이고 있다. 이것은 변형중에 유도된 마르텐사이트의 양이 적게 형성되는 사실에 기인하며, 변형에 따른 $\alpha$ 마르텐사이트 변태는 교류자화율과 금속입자 시험으로 알 수 있다.

• 물과 미래
• /
• 제27권2호
• /
• pp.73-83
• /
• 1994

확산현상, 표사유동 및 인간의 여러 활동이 실제 연안해역에서 일어나므로 연안해역 해수운동의 물리적 특성을 파악하고 해석하는 것은 중요한 의미를 지닌다. 본 연구에서는 연안해역에서의 파랑변형과 평균해수위 변동 그리고 연안유속 분포양상에 대해 여러 인자들이 미치는 영향을 2차원 유한차분 모형(ADI, Up-wind)을 이용하여 분석하였다. 계산결과로는 수치모형을 해저경사가 일정한 2차원 지형에 적용하여 해저경사, 입사파고, 파향각, 파주기, 마찰계수 및 수평확산계수가 연안해역 특히 쇄파대내에서 파랑변형, 평균해수위 변동 및 연안유속 분포에 미치는 영향을 분석하였다.