• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.2
• /
• pp.62-67
• /
• 2013

The influence of internal stress and joint strength(shear, tensile) according to the deposition conditions was investigated by the Polyimide substrate and ZnO thin film. Deposition thickness and temperature affect the internal stress and the internal stress was minimum at the 60nm and $200^{\circ}C$ of the deposition conditions. Tensile strength is large at the deposition condition that shear strength is large and the shear strength was about 50% of the tensile strength. The shear strength and tensile strength were large at deposition condition that internal stress was small. Crack occurred near the joint interface of Polyimide substrate and progressed along the interface until the final fracture.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.8
• /
• pp.2626-2636
• /
• 1996

A study of soot deposition and reentrainment was carried out both theoretically and experimentally to understand behavior of soot formed by incomplete combustion in a diesel engine. Theoretically, soot deposition on engine cylinder wall and/or piston head was studied with a stagnation point flow approximation. Soot reentrainment occurred upon exhaust gas blowdown was also studied by assuming a long-normal shear velocity distribution. Experimentally, a LPG$O_2/N_2$ flame impinging on a disk, produced by a concentric tubular burner, was chosen as deposition configuration and a shear flow unit with compressed air was installed for the study of reentrainment. For selected flame configuration, soot deposition measurements were conducted and showed that the dominant deposition mechanism was thermophoresis. Distributions of gas temperature and soot number density were estimated by combining data obtained by a B-type thermocouple with a thermophoretic transport theory. Disk temperature distributions were directly measured using a K-type thermocouple. Soot size and morphology were estimated from a TEM photograph. Ratios of soot deposit to reentrained amount were measured for a wide range of shear flow velocities, which showed that the reentrainment model was reasonable.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.284-284
• /
• 2006

Electrospray deposited films of poly(vinylidene fluoride) were prepared with various conditions. A model has been developed, which provides the state of the electrosprayed droplet at impact. With a combination of the experimental films and the model calculations, it can be shown that growth rate, the increase of the sprayed solution on the substrate per second, defines the film morphology in electrospray deposition. Growth rate indicates which factors play the main role in the film formation process. The most important factors are liquid flow, surface tension and shear rate. The model can calculate the shear rate and it is shown that PVDF, and most likely polymers in general, has a large range of growth rates, where the morphology only depends on the shear rate of the depositing droplet. This method can also be used to describe electrospray deposition of other compounds.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.1 no.1
• /
• pp.44-49
• /
• 1989

Cohesive sedimentation mechanism is affected by various physico-chemical factors. Thus, the field observations and the laboratory experiments for cohesive sediment have been reported for decades. Erosion and deposition test was carried out with cohesive sediment material sampled in the Keum River Estuary in this study. The change of the suspended cohesive sediment concentration was measured for various flow conditions, which have the purpose to determine the critical shear stress and the coefficients for erosion and deposition . The critical shear stress and the coefficient for erosion were determined in the flume test. The equilibrium concentration was determined for each shear stress and the relationship between the normalized equilibrium cocentration with the initial cocentration (Ceq/co) and the equivalent shear stress was obtained. The experimental results were compared with the other results and showed fairly well agreements with them.

• Geotechnical Engineering
• /
• v.4 no.4
• /
• pp.5-18
• /
• 1988

A series of CU triaxial compression tests were conducted to investigate the variation of -untrained shear strength of underconsolidated clay at different degrees of consolidation. The soil samples were artificially made by one-dimensional consolidation using soft Bangkok Clay. The test results showed that the undrained shear strength of clay parabolically increased convoking downward with increasing degrees of consolidation. However, all the measured shear strength were unanimously related to the effective stress. These experimental results were used in the numerical analysis. A finite element computer program was developed to investigate the stability of submarine .slope undergoing rapid deposition taking into account the variation in soil compressibility and permeability during the consolidation process. The relationships of degree of consolidation with time as a function of rate of deposition and angle of slope were established. A method of predicting the time of slope failure and the volume of moving mass of soil was also made.

• Journal of Korea Water Resources Association
• /
• v.41 no.9
• /
• pp.863-872
• /
• 2008

In this study, a series of deposition tests have been conducted on saltwater condition(salinity 32 %o) using an annular flume, in order to estimate depositional properties of kaolinite sediments and to analyze the effect of the initial concentration on them. Total 37 deposition tests have been carried out in three different initial concentrations (1000, 5000, 15000 ppm) with varying the bed shear stress. From these test results, minimum shear stress (or critical shear stress for deposition; ${\tau}_{bmin}$) and the deposition rate parameters (${\sigma}_1,\;({\tau}^*_b-1)_{50},\;{\sigma}_2,\;t_{50}$) for kaolinite sediments have been quantified, and the effects of the initial concentration and salinity on depositional properties of cohesive sediments have been analyzed qualitatively. As the results, ${\tau}_{bmin},\;{\sigma}_1\;and\;({\tau}^*_b-1)_{50}$ are found to be 0.147, 0.74 and $0.65N/m^2$ respectively. Through comparing with results from previous studies, the performance of this study and tests results are shown to be good enough to verify.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.6
• /
• pp.662-669
• /
• 2015

There has been an increased interest in the mitigation of wax deposition because wax, which usually accumulates in subsea oil-production systems, interrupts stable oil production and significantly increases the cost. To guarantee a required oil flow by mitigating wax deposition, we need to obtain a reliable estimation of the wax deposition. In this research, we perform simulations to understand the major mechanisms that lead to wax deposition, namely molecular diffusion, shear stripping reduction, and aging. While the model variables (shear reduction multiplier, wax porosity, wax thermal conductivity, and molecular diffusion multiplier) can be measured experimentally, they have high uncertainty. We perform an analysis of these variables and the amount of water and gas in the multiphase flow to determine these effects on the behavior of wax deposition. Based on the results obtained during this study for a higher wax porosity and molecular diffusion multiplier, we were able to confirm the presence of thicker wax deposits. As the shear reduction multiplier decreased, the thickness of the wax deposits increased. As the amount of water increased, there was also an increase in the amount of wax deposits until 40% water cut and decreased. As the amount of gas increased, the amount of wax deposits increased because of the loss of the light hydrocarbon component in the liquid phase. The results of this study can be utilized to estimate the wax deposition behavior by comparing the experiment (or field) and simulation data.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.24 no.3
• /
• pp.159-165
• /
• 2012

In this study, a series of deposition tests have been performed using an annular flume and depositional parameters of natural cohesive sediments have been estimated domestically for the first time. The natural cohesive sediments for deposition tests have been collected from Kwangyang Bay and total 18 deposition tests have been carried out on different bed shear stress respectively but with the same initial concentration. Test results for natural cohesive sediments of Kwangyang bay show that minimum bed shear stress ${\tau}_{bmin}$, standard deviation ${\sigma}_1$, and time scale parameter $({\tau}_b^*-1)_{50}$ are $0.11N/m^2$, 0.68 and 0.85, respectively. Through the comparison with results of previous studies for other sediments, the results of this study are shown to be good enough to verify.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.27 no.6
• /
• pp.434-442
• /
• 2015

In this study, a series of deposition tests have been performed using an annular flume in order to estimate depositional parameter of natural sediments. The sediment of Masan Port has been collected for deposition tests, and total 18 deposition tests have been carried out on different bed shear stress respectively but with the same initial concentration. As the results, the minimum bed shear stress ${\tau}_{bmin}$, standard deviation ${\sigma}1$ and time scale parameter $({\tau}_b^*-1)_{50}$ are found to be $0.10N/m^2$, 0.54 and 0.87 respectively. Through comparing with results from previous studies for other sediments, the results of this study are shown to be good enough to verify.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1998.04a
• /
• pp.105-109
• /
• 1998

1. Introduction : In microfiltration the transport, deposition and removal of particles control cake formation on a filter. In this connection a new model on cake formation, based on the wall shear stress, was tested here in comparison with experiments of fine particle slurry under Taylor-vortex flow. The model expresses the deposition process for particles as two first-order steps in series of mass transfer and adhesion, and their removal process as a linear relation to the wall shear stress. This embraces characteristics of both dead-end and crossflow filtration. The correlation resulting from fitting to experimental data represented the experimental data reasonably well. This study will be helpful in analyzing fouling in heat exchangers.