• Korea-Australia Rheology Journal
• /
• 제20권3호
• /
• pp.109-116
• /
• 2008

The effect of intermolecular aggregation induced by hydrophobic and electrostatic interactions on shear and elongational flow properties of aqueous acrylic thickener solutions is discussed. Complex shear modulus is determined at frequencies up to $10^4$ rad/s employing oscillatory squeeze flow. Extensional flow behavior is characterized using Capillary Break-up Extensional Rheometry. Aqueous solutions of poly(acrylic acid)(PAA)/poly(vinylpyrrolidone-co-vinylimidazole) (PVP-VI) mixtures exhibit unusual rheological properties described here for the first time. Zero-shear viscosity of the mixtures increases with decreasing pH and can exceed that of the pure polymers in solution by more than two orders of magnitude. This is attributed to the formation of complexes induced by electrostatic interactions in the pH range, where both polymers are oppositely charged. PAA/PVP-VI mixtures are compared to the commercial thickener Sterocoll FD (BASF SE), which is a statistical co-polymer including (meth) acrylic acid and ethylacrylate (EA) forming aggregates in solution due to "sticky" contacts among hydrophobic EA-sequences. PAA/PVP-VI complexes are less compact and more deformable than the hydrophobic Sterocoll FD aggregates. Solutions of PAA/PVP-VI exhibit a higher zero-shear viscosity even at lower molecular weight of the aggregates, but are strongly shear-thinning in contrast to the weakly shear-thinning solutions of Sterocoll FD. The higher ratio of characteristic relaxation times in shear and elongation determined for PAA/PVP-VI compared to Sterocoll FD solutions reflects, that the charge-induced complexes provide a much stronger resistance to extensional flow than the aggregates formed by hydrophobic interactions. This is most likely due to a break-up of the latter in extensional flow, while there is no evidence for a break-up of complexes for PAA/PVP-VI mixtures. These flexible aggregates are more suitable for the stabilization of thin filaments in extensional flows.

• Fibers and Polymers
• /
• 제6권4호
• /
• pp.289-296
• /
• 2005

Biodegradable nanocomposites were prepared by mixing a polymer resin and layered silicates by the melt intercalation method. Internal structure of the nanocomposite was characterized by using the small angle X-ray scattering (SAXS) and transmission electron microscope (TEM). Nanocomposites having exfoliated and intercalated structures were obtained by employing two different organically modified nanoclays. Rheological properties in shear and extensional flows and biodegradability of nanocomposites were measured. In shear flow, shear thinning behavior and increased storage modulus were observed as the clay loading increased. In extensional flow, strain hardening behavior was observed in well dispersed system. Nanocomposites with the exfoliated structure had better biodegradability than nanocomposites with the intercalated structure or pure polymer.

• Journal of Welding and Joining
• /
• 제28권2호
• /
• pp.74-78
• /
• 2010

In this paper, a non-contact method of evaluating the thickness reduction in an aluminum sheet caused by corrosion and friction using SH-EMAT (shear horizontal, electromagnetic acoustic transducer) is described. Since this method is based on the measurement of the time-of-flight and amplitude change of guided waves caused from the thickness reduction, it provides information on the thinning defects. Information was obtained on the changes of the various wave features, such as their time-of-flight and amplitude, and their correlations with the thickness reduction were investigated. The interesting features in the dispersive behavior of selected guided modes were used for the detection of thinning defects. The measurements of these features using SH waves were performed on aluminum specimens with regions thinned by 7.2% to 29.5% of the total thickness. It is shown that the time-of-flight measurement provides an estimation of the thickness reduction and length of the thinning defects.

• 폴리머
• /
• 제38권3호
• /
• pp.286-292
• /
• 2014

에너지 고분자인 poly(BAMO-AMMO)와 유사한 특성을 갖는 폴리에틸렌 플라스토머인 Exact를 고분자 결합제로, RDX(research department explosive)와 유사한 특성을 갖는 dechlorane을 충전제로 사용한 고농축 복합화약 시뮬란트 현탁계의 유변물성을 연구하였다. 회분식 용융혼련기를 사용하여 현탁계의 혼화거동을 조사하였는데 상당한 점성소산열이 발생하였다. 충전율이 70 v% 이상에서는 토크의 지속적인 감소가 있었는데 이는 벽면 미끌어짐 현상에 기인한다고 사료되었다. SEM 관찰 결과 충전제 입자들은 잘 분산되어 있었고 혼화 조건의 영향은 크지 않은 것으로 판단되었다. 현탁계의 뚜렷한 전단박화(shear thinning) 특성으로 인하여 낮은 전단속도의 평판-평판 레오미터에서 측정이 어려운 고충전 현탁계도 높은 전단속도의 모세관 레오미터에서 유변물성 측정이 가능하였다.

• Journal of Pharmaceutical Investigation
• /
• 제37권3호
• /
• pp.137-148
• /
• 2007

Using a strain-controlled rheometer [Rheometrics Dynamic Analyzer (RDA II)], the steady shear flow properties of a semi-solid ointment base (vaseline) have been measured over a wide range of shear rates at temperature range of $25{\sim}60^{\circ}C$. In this article, the steady shear flow properties (shear stress, steady shear viscosity and yield stress) were reported from the experimentally obtained data and the effects of shear rate as well as temperature on these properties were discussed in detail. In addition, several inelastic-viscoplastic flow models including a yield stress parameter were employed to make a quantitative evaluation of the steady shear flow behavior, and then the applicability of these models was examined by calculating the various material parameters (yield stress, consistency index and flow behavior index). Main findings obtained from this study can be summarized as follows : (1) At temperature range lower than $40^{\circ}C$, vaseline is regarded as a viscoplastic material having a finite magnitude of yield stress and its flow behavior beyond a yield stress shows a shear-thinning (or pseudo-plastic) feature, indicating a decrease in steady shear viscosity as an increase in shear rate. At this temperature range, the flow curve of vaseline has two inflection points and the first inflection point occurring at relatively lower shear rate corresponds to a static yield stress. The static yield stress of vaseline is decreased with increasing temperature and takes place at a lower shear rate, due to a progressive breakdown of three dimensional network structure. (2) At temperature range higher than $45^{\circ}C$, vaseline becomes a viscous liquid with no yield stress and its flow character exhibits a Newtonian behavior, demonstrating a constant steady shear viscosity regardless of an increase in shear rate. With increasing temperature, vaseline begins to show a Newtonian behavior at a lower shear rate range, indicating that the microcrystalline structure is completely destroyed due to a synergic effect of high temperature and shear deformation. (3) Over a whole range of temperatures tested, the Herschel-Bulkley, Mizrahi-Berk, and Heinz-Casson models are all applicable and have an almostly equivalent ability to quantitatively describe the steady shear flow behavior of vaseline, whereas the Bingham, Casson,and Vocadlo models do not give a good ability.

• Food Science and Biotechnology
• /
• 제15권6호
• /
• pp.871-876
• /
• 2006

Rheological behavior of commercial hot pepper-soybean paste (HPSP) was evaluated in small amplitude oscillatory and steady shear tests. Storage modulus (G'), loss modulus (G"), and complex viscosity (${\eta}^*$) as a function of angular frequency (${\omega}$), and shear stress (${\sigma}$) as a function of shear rate (${\gamma}$) data were obtained for 5 commercial HPSP samples. HPSP samples at $25^{\circ}C$ exhibited a non-Newtonian, shear-thinning flow behavior with high yield stresses and their flow behaviors were described by power law, Casson, and Herschel-Bulkley models. Time-dependent flow properties were also described by the Weltman, Hahn, and Figoni & Shoemaker models. Apparent viscosity over the temperature range of $5-35^{\circ}C$ obeyed the Arrhenius temperature relationship with activation energies (Ea) ranging 18.3-20.1 kJ/mol. Magnitudes of G' and G" increased with an increase in ${\omega}$, while ${\eta}^*$ decreased. G' values were higher than G" over the most of the frequency range (0.63-63 rad/sec), showing that they were frequency dependent. Steady shear viscosity and complex viscosity of the commercial HPSP did not fit the Cox-Merz rule.

• Elastomers and Composites
• /
• 제48권1호
• /
• pp.18-23
• /
• 2013

용융상태에서 nylon 12 elastomer에 소량의 dicumyl peroxide (DCP) 와 triallyl cyanuate (TAC)를 첨가하여 nylon 12 elastomer를 부분적으로 가교시켰으며, 이에 따른 nylon 12 elastomer의 기계적, 동적기계적 그리고 유변학적 특성을 tensile test, DMA, small amplitude oscillating rheometer를 이용하여 각각 알아보았다. TAC의 함량이 증가함에 따라 인장탄성률과 영률은 증가하고, 파단신율은 감소하였다. DMA 측정결과, DCP로 부분적으로 가교시킨 nylon 12 elastomer의 PTMG상의 유리전이온도는 순수한 nylon 12 elstomer에 비해 증가하였고, storage modulus는 nylon 12상의 용융온도 이상에서도 거의 일정한 값을 나타내었다. 부분적으로 가교시킴에 따른 유변학적 특성의 변화는 TAC의 함량이 증가함에 따라 solid like behavior와 shear thinning behavior가 점점 뚜렷하게 나타남을 알 수 있었다. 이로부터 nylon 12 elastomer를 용융상태에서 부분적으로 가교시킴으로써 용융가공성을 저하시키지 않으면서, 기계적 물성은 효과적으로 향상시킬 수 있었으며, 특히, nylon 12 elastomer의 사용가능 온도범위를 증가시킬 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제21권9호
• /
• pp.835-843
• /
• 2008

We have fabricated the source-drain electrodes for OTFTs by screen printing method and manufactured Ag pastes as conductive paste. To obtain excellent conductivity and screen-printability of Ag pastes, the dispersion characteristics of Ag pastes prepared from two types of acryl resins with different molecular structures and Ag powder treated with caprylic acid, triethanol amine and dodecane thiol as surfactant respectively were investigated. The Ag pastes containing Ag powder treated with dodecane thiol having thiol as anchor group or AA4123 with carboxyl group(COOH) of hydrophilic group as binder resin exhibited excellent dispersity. But, Ag pastes(CA-41, TA-41, DT-41) prepared from AA4123 fabricated the insulating layer since the strong interaction between surface of Ag powder and carboxyl group(COOH) of AA4123 interfered with the formation of conduction path among Ag powders. The viscosity behavior of Ag pastes exhibited shear-thinning flow in the high shear rate range and the pastes with bad dispersion characteristic demonstrated higher shear-thinning index than those with good dispersity due to the weak flocculated network structure. The output curve of OTFT device with a channel length of 107 ${\mu}m$ using screen-printed S-D electrodes from DT-30 showed good saturation behavior and no significant contact resistance. And this device exhibited a saturation mobility of $4.0{\times}10^{-3}$ $cm^2/Vs$, on/off current ratio of about $10^5$ and a threshold voltage of about 0.7 V.

• Macromolecular Research
• /
• 제13권5호
• /
• pp.409-417
• /
• 2005

The surface of rutile titania nanoparticles was chemically modified by reacting with alkoxy silane. The surface and rheological properties in silicone oil having a wide range of viscosity were investigated. Total surface free energy($\gamma_S$) of the titania particles decreased from 53.12 to 26.94 mJ/$m^2$ as the silane used for surface treatment was increased from 0 to 5.0 wt$\%$. The surface free energy of neat silane was 25.5 mJ/$m^2$, which is quite close to that oftitania particles treated with 5.0 wt$\%$ silane. Due to the hydrophobic nature oftreated-titania, the contact angle was accordingly higher for polar solvent in the order of water>ethylene glycol> formamide>$\alpha$-bromonaphthalene. In sum of rheological behavior, as the applied shear stress or viscosity of the silicone oil increased, the titania particles tend to form layers and agglomerated clusters, showing shear-thinning and shear-thickening behaviors, sequentially. A good dispersion of discrete titania particles obeying a Newtonian flow behavior was achieved at a surface energy or low concentration of silane-treated titania particles in hydrophobic silicone oil.

• 한국세라믹학회지
• /
• 제42권11호
• /
• pp.737-742
• /
• 2005

Rheological properties of ordinary portland cement (OPC) containing metakaoline (MK), granulated blast furnace slag (GBS) and polycarboxylate type superplasticizer (PCA) were investigated using a mini-slump test, sedimentation test and viscometer. Fluidity of cement pastes containing MK (OPC-MK, OPC-MK-GBS systems) with PCA were higher than those of the cement pastes without MK(OPC, OPC-GBS systems). Colloid suspensions with $0.1\%$ PCA were changed from stable sedimentation behaviors to flocculation behaviors in the OPC-MK, OPC-GBS and OPC-MK-GBS systems. The colloid suspensions showed stable sedimentation behaviors with PCA greater than $0.2\%$. The OPC system showed shear thinning behavior. However, the other systems showed weak shear thinning behaviors with PCA. Rheological properties of cement pastes were improved when MK and GBS were contained together. The rheological properties of OPC-MK, OPC-GBS and OPC-MK-GBS systems were improved by PCA added greater than $0.2\%$.