• 접착 및 계면
• /
• 제5권2호
• /
• pp.22-36
• /
• 2004

Several in-situ testing methods of adhesively bonded joints under static short-time tensile loading are critically analyzed in terms of experimental procedure and data evaluation. Due to its rather homogeneous stress state across the glue line, the tensile-shear test with thick single-lap specimens, according to ISO 11003-2, has become the most important test process for the determination of realistic materials parameters. This basic method, which was improved in both, the experimental part by stepped adherends and easily attachable extensometers and the evaluation procedure by numeric substrate deformation correction and test simulation based on the finite element method (FEM), is therefore demonstrated by application to several kinds of adhesives and metallic adherends. Multi-axial load decreases the strength of a joint. This effect, which is illustrated by an experimental comparison, impedes the derivation of realistic mechanical characteristics from measured force-displacement curves. It is shown by numeric modeling that tensile-shear tests with thin plate substrates according to ISO 4587, which are widely used for quick industrial quality assurance, reveal an inhomogeneous stress state, especially because of relatively large adherend deformation. Complete experimental determination of the elastic properties of bonded joints requires independent measurement of at least two characteristics. As the thick-adherend tensile-shear test directly yields the shear modulus, the tensile butt-joint test according to ISO 6922 represents the most obvious complement of the test programme. Thus, validity of analytical correction formulae proposed in literature for the derivation of realistic materials characteristics is verified by numeric simulation. Moreover, the influence of the substrate deformation is examined and a FEM correction method introduced.

• 한국산학기술학회논문지
• /
• 제14권10호
• /
• pp.5290-5298
• /
• 2013

본 논문에서는 프리캐스트 방식으로 제작 가능한 격자형 강합성 바닥판의 이음부에 기계식 연결방식을 적용하고자 콘크리트 전단키와 고장력볼트로 구성되는 이음부에 대해 Push-out 시험으로 전단내력을 구하였으며, 이를 전단마찰 이론에 근거한 이론식 및 설계식과 비교함으로써 전단내력을 평가하였다. 분석결과에 따르면, 이음부 접합면을 에폭시로 부착한 경우가 전단키를 강판으로 보강한 경우 보다 약 10% 정도 더 큰 전단내력을 갖는 것으로 나타났으나, 실험체간 전단내력의 편차는 전단키를 강판으로 보강한 경우가 더 작게 나타났다. 실험결과를 계산식 및 설계식과 비교한 결과, 기존 설계식으로 안전하게 설계될 수 있음을 알 수 있었다. 그러나, ACI-318에 의할 경우 이음부 전단내력이 과소평가되기 때문에 LRFD에서 제시된 설계식의 적용이 더 적당한 것으로 분석되었다.

• 대한금속재료학회지
• /
• 제47권9호
• /
• pp.580-585
• /
• 2009

The effects of shear speed and tip height on the high speed shear test of Sn-3.0wt.%Ag-0.5wt.%Cu ball joints were investigated. Solder balls of $450{\mu}m$ in diameter were reflowed at $245^{\circ}C$ on a FR4 PCB (Printed Circuit Board) in order to obtain a sample for the high-speed shear test. The UBM was comprised of Cu/Ni/Au, and the shear speed and tip height varied from 0.5 to 3.0 m/s, and from 10 to $135{\mu}m$, respectively. According to the experimental results, faster shear speed enhanced the shear strength of the solder joints, regardless of the tip height. The fraction of ductile (solder) fracture decreased when the shearing speed was raised from 0.5 to 3.0 m/s. With an increasing tip height from 10 to 50 and $135{\mu}m$, the fracture mode changed from pad lift to mixed (ductile and brittle) and ductile fracture, respectively, while the shearing energy also increased in the same order. The shear energy had a proportional relationship with the fraction of the solder fracture.

• 터널과지하공간
• /
• 제33권1호
• /
• pp.10-28
• /
• 2023

고준위방사성폐기물 처분장의 장기 안정성을 확보하기 위해서 암반 불연속면의 장기적인 전단 거동을 분석하고 그 안정성을 평가해야 한다. 암반 불연속면의 장기 전단 거동은 크리프 모델, RSF 모델로 모사될 수 있고, 전단 크리프 시험, 속도 단계 시험, 슬라이드-홀드-슬라이드 시험을 통해 모델에 필요한 파라미터를 결정하거나 여러 조건에서 전단 거동을 분석하는 실험을 수행할 수 있다. 기존 연구에 따르면 전단 실험을 위하여 직접전단시험기, 삼축압축시험기, 이축전단시험기가 주로 이용되었으며 현지 암반의 열-수리-역학적인 조건을 재현하기 위해 다양하게 개선된 장비가 이용되었고 그에 따라 다양한 양상의 전단 거동이 관찰되었다. 그러므로 국내 고준위방사성폐기물 처분장을 설계하기 위해서 처분장 부지의 암종, 열-수리-역학적 조건, 광물의 변성, 그리고 전단 저항의 회복 등을 고려하여 암반 불연속면의 장기 거동을 검토해야 한다.

• 한국전산구조공학회논문집
• /
• 제18권2호
• /
• pp.201-211
• /
• 2005

철근콘크리트 부재의 전단거동에 대한 오랜 연구에 의하여 이에 대한 다양한 이론모델들과 제안식들이 존재한다. 그러나 전판거동의 메커니즘이 복잡하고 영향을 미치는 요소들이 많아서 이론모델들은 대부분 매우 복잡한 경향이 있고, 실험에 의한 제안식들은 제한된 범위내의 실험변수에 대해서만 유효한 경우가 많다. 이러한 문제점을 해결할 수 있는 대안의 하나로써 인공신경망이 여러 연구자들에 의하여 제안되어 왔으며, 본 논문에서는 인공신경망을 이용하여 전단보강근이 없는 철근콘크리트 보의 전단강토를 예측하였다 특히, 기존의 전단실험결과를 광범위하게 모아 구축한 데이타베이스를 활용함으로써 넓은 범위의 구조변수들을 포함한 다양한 부재들을 인공신경망의 훈련자료로 이용하였고, 인공신경망에 의한 전단강토 예측 결과를 ACI의 규준식, Zsutty, Okamura의 제안식들과도 비교 분석하였다. ACI의 규준식은 전단보강근이 없는 철근콘크리트 부재에 대해서 매우 부정확한 전단강도를 제공하였으며, Zsutty의 제안식은 ACI의 규준식에 비해 향상된 예측 결과를 보였으나 부재의 크기효과를 반영하지 못하였다. Okamura의 제안식은 주요 변수들의 영향을 비교적 잘 반영하여 상당히 정확하면서도 안정적인 전단강토를 제공하였다 이에 비해 인공신경망은 실험 결과에 가장 근접한 부재의 전단강도를 제공함으로써, 다양한 변수들의 영향을 매우 정확하게 반영할 수 있는 것으로 나타나서 인공신경망이 전단강도와 같이 메커니즘이 복잡하고 영향을 끼치는 변수들이 많은 다른 구조적 거동이나 강도를 예측하는데 매우 적절한 수단을 제공할 수 있음을 보여주었다.

• 한국지진공학회논문집
• /
• 제20권4호
• /
• pp.211-222
• /
• 2016

Reinforced concrete shear walls with deficient reinforcement details are tested under cyclic loading. The deficiency of reinforcement details includes insufficient splice length in U-stirrups at the ends of horizontal reinforcement and boundary column dowel bars found in existing low- to mid-rise Korean buildings designed non-seismically. Three test specimens have rectangular, babel and flanged sections, respectively. Flexure- and shear-controlled models for reinforced concrete shear walls specified in ASCE/SEI 41-13 are compared with the flexural and shear components of force-displacement relation extracted separately from the top displacement of the specimen based on the displacement data measured at diverse locations. Modification of the shear wall models in ASCE/SEI 41-13 is proposed in order to account for the effect of bar slip, cracking loads in flexure and shear. The proposed modification shows better approximation of the test results compared to the original models.

• Steel and Composite Structures
• /
• 제17권6호
• /
• pp.967-980
• /
• 2014

In regions of high shear forces in composite bridges, headed stud shear connectors need to be arranged with a small spacing in order to satisfy the design requirement of resisting the high interface shear force present at this location. Despite this, studies related to groups of headed studs are somewhat rare. This paper presents an investigation of the static behaviour of grouped stud shear connectors in high-strength concrete. Descriptions are given of five push-out test specimens with different arrangements of the studs that were fabricated and tested, and the failure modes, load-slip response, ultimate load capacities and related slip values that were obtained are reported. It is found that the load-slip equation given by some researchers based on a single stud shear connector in normal strength concrete do not apply to grouped stud shear connectors in high-strength concrete, and an algebraic load-slip expression is proposed based on the test results. Comparisons between the test results and the formulae provided by some national codes show that the equations for the ultimate capacity provided in these codes are conservative when used for connectors in high-strength concrete. A reduction coefficient is proposed to take into account the effect of the studs being in a group.

• 한국환경복원기술학회지
• /
• 제5권4호
• /
• pp.19-30
• /
• 2002

The stability of slope using root-pile like to the reinforcements is affected by the interaction behavior mechanism of soil-reinforcements. Through the studying on the interaction in joint of its, therefore, the control roles can be find out in installed slope. In study, the stress level ratio based on the insert angle of installed reinforcements in soil used to numerical analysis, which was results from the duty direct shear test in Lab. The maximum shear strain variation on the reinforcements was observed at insert angle, which was approximately similar to the calculated angle based on the equation proposed by the Jewell. The elasto-plastic joint model on the contact area of soil-reinforcements was presumed, the reinforced soil assumed non-linear elastic model and the reinforcements supposed elastic model, respectively. The finite element analysis of assumed models was performed. The shear strain variation of non-reinforced state obtained by the FEM analysis including elasto-plastic joint elements were shown the rationality of general limit equilibrium analysis for the slope failure mode on driving zone and resistance zone, which based on the stress level step according to failure ratio. Through the variation of shear strain for the variation of inserting angle of reinforcements, the different mechanism on the bending and the shear resistance of reinforcements was shown fair possibility.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.1278-1284
• /
• 2008

This study carried out bender element tests in a calibration chamber in order to estimate the characteristics of soil specimen prepared in a calibration chamber. Basically, the purpose of bender element test is to measure the shear wave velocity. Bender element test cannot only confirm the status of soil specimen deposited in a chamber, but also estimate the consolidation process indirectly. In order to carry out bender element test in a calibration chamber, a pair of bender elements was installed inside the chamber, using the 'ㄷ' shaped frame. For the sandy soils having various relative densities in various stress conditions, the maximum shear modulus was estimated. From the comparison with bender element test results in a triaxial testing device, testing device and procedure was validated.

• Geomechanics and Engineering
• /
• 제13권5호
• /
• pp.809-823
• /
• 2017

This paper describes lab test results of artificial rock-like material samples having a plane joint. Cyclic shear tests were performed under different normal loads and different shear displacement amplitudes. For this purpose, multi-stage normal loading tests (30 kN, 60 kN, 90 kN, 180 kN, 360 kN and 480 kN) with cyclic excitation at frequency of 1.0 Hz and different shear displacement amplitudes (0.5 mm, 1.0 mm, 2.0 mm, 4.0 mm, 5.0 mm, and 8.0 mm) were conducted using the big shear box device GS-1000. Experimental results show, that shear forces increase with the increase of normal forces and quasi-static friction coefficient is larger than dynamic one. With the increase of normal loads, approaching the peak value of shear forces needs larger shear displacements. During each cycle the normal displacements increase and decrease (rotational behavior in every cycle). Peak angle of inclination increases with the increase of normal load. A phase shift between maximum shear displacement and maximum shear force is observed. The corresponding time shift decreases with increasing normal load and increases with increasing shear displacement amplitudes.