• Computers and Concrete
• /
• v.8 no.6
• /
• pp.735-755
• /
• 2011

The capability of a multi-directional fixed smeared crack constitutive model to simulate the flexural/punching failure modes of fiber reinforced concrete (FRC) laminar structures is discussed. The constitutive model is implemented in a computer program based on the finite element method, where the FRC laminar structures were simulated according to the Reissner-Mindlin shell theory. The shell is discretized into layers for the simulation of the membrane, bending and out-of-plane shear nonlinear behavior. A stress-strain softening diagram is proposed to reproduce, after crack initiation, the evolution of the normal crack component. The in-plane shear crack component is obtained using the concept of shear retention factor, defined by a crack-strain dependent law. To capture the punching failure mode, a softening diagram is proposed to simulate the decrease of the out-of-plane shear stress components with the increase of the corresponding shear strain components, after crack initiation. With this relatively simple approach, accurate predictions of the behavior of FRC structures failing in bending and in shear can be obtained. To assess the predictive performance of the model, a punching experimental test of a module of a façade panel fabricated with steel fiber reinforced self-compacting concrete is numerically simulated. The influence of some parameters defining the softening diagrams is discussed.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.2
• /
• pp.75-85
• /
• 2004

Various geosynthetics are widely installed as a liner or a protective layer of waste landfills. The interface shear strength between the layers of geosynthetics in waste landfills is an important parameter to ensure the safety of bottom and cover system design. In this study, estimations of interface shear strength between geomembrane and geotextile or Geosynthetic Clay Liners (GCL) are performed by large direct shear tests. Especially, this research is focused on the effect of moisture within the interface shear strength between geosynthetics, because most interfaces are vulnerable to rain, leachate and groundwater beneath the liners.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.321-328
• /
• 2002

Various geosynthetics used as liners or the Protection layers are installed in the solid waste landfill. The interface shear strength between geosynthetics installed at the slope of the landfill is a very important variable for the safe design of bottom and cover systems in the solid waste landfill. The interface shear strengths between (1) Geomembrane(GM)/Geotexile(GT) and (2) Geomembrane(GM)/Geosynthetic Clay Liner(GCL) were estimated by a large direct shear test in this study and were evaluated by the Mohr-Coulomb failure criterion. Especially, this research is focused on the effect of water which exists between geosynthetics because interfaces become easily wet or hydrated by rain, leachate and groundwater beneath liners. The strength reduction at large displacement and the effects of the magnitude of normal stresses and GCL hydration methods also investigated. The test results showed that the interface shear strength and shear behavior varied depending upon the magnitude of normal stresses, water at the interface, and hydration methods. Summary of secant friction angles, which could be used as reference values at a site where similar geosynthetics are installed, together with normal stress and hydration condition are presented.

• Transactions of Materials Processing
• /
• v.15 no.7 s.88
• /
• pp.479-484
• /
• 2006

The evolution of strain states and textures during rolling with various conditions was investigated by finite element method (FEM) simulations and measurements of rolling textures. Symmetrical rolling with a high friction gives rise to a strong variation of shear strains in rolled sample leading to the formation of texture gradients throughout the thickness layers. A small variation of shear strains during rolling with a well lubrication condition leads to the formation of a fairly homogeneous rolling texture throughout the sheet thickness. During asymmetrical rolling, a proper control of rolling parameters provides the evolution of a fairly homogeneous shear texture throughout the whole sheet thickness.

• Journal of Mechanical Science and Technology
• /
• v.14 no.9
• /
• pp.920-927
• /
• 2000

A multi-layered orthotropic material with a center crack is subjected to an anti-plane shear loading. The problem is formulated as a mixed boundary value problem by using the Fourier integral transform method. This gives a Fredholm integral equation of the second kind. The integral equation is solved numerically and anti-plane shear stress intensity factors are analyzed in terms of the material orthotropy for each layer, number of layers, crack length to layer thickness and the order of the loading polynomial. Also, the case of monolithic and hybrid composites are investigated in terms of the local fiber volume fraction and the global fiber volume fraction.

• Transactions of Materials Processing
• /
• v.13 no.4
• /
• pp.382-387
• /
• 2004

The continuous confined strip shearing (CCSS) based on the equal channel angular pressing (ECAP) was modeled by means of a rigid-plastic two-dimensional finite element method (FEM). Parallel to the simulations, samples of AA 1050 sheets were experimentally deformed by CCSS. The CCSS deformation led to the formation of through thickness texture gradients comprising a strong shear texture in the sheet center and weak shear textures in the sheet surfaces. FEM analysis revealed variations in the strain component $\varepsilon_13$ along the sample thickness direction, which gave rise to the evolution of different textures. A high friction between the sample and die surface was responsible for lowering intensities of the shear texture components in thickness layers close to the surfaces.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1998.10a
• /
• pp.423-430
• /
• 1998

Elastomeric bearings are frequently used as a means to isolate structural systems from earthquake loadings. The combination of rubber layers and reinforcing steel shims makes the bearings stiff axially but soft laterally The shear flexibility of these short columns can lead to relatively low buckling loads which may be further reduced when high shear strains are simultaneously imposed. The area reduction formula has been proposed to account for the reduction in buckling load due to shear. The result obtained from the formula is presumed to be conservative but the degree of conservatism is unknown. This paper describes a numerical study which aims at determining the effect of high shear strain on the critical load of rubber bearings. The results from the finite element analysis which accounts for both the material and geometric non-linearities are compared against the theoretical results in order to examine the validity of the theoretical formulas.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.8 s.185
• /
• pp.137-144
• /
• 2006

This study is concerned with the relation between steelbelt width and belt edge separation of a tire. Belt edge separation causes tire burst and threatens passenger's safety. For the reason, it is important to predict durability caused by belt edge separation in the early stage of the tire structure design. Usually, passenger car tires have two layers of steelbelts having opposite steel cord's angles, which makes a shear behaviour between each belt layer. Shear behaviour is one of reason to cause belt edge separation. In this study, to predict belt edge separation, we suggested the prediction method of belt edge separation and evaluated the effect of steelbelt width on the belt edge separation using FEM. We also studied on main parameters to affect shear behaviour at the belt edge area.

• Korean Journal of Poultry Science
• /
• v.44 no.1
• /
• pp.41-49
• /
• 2017

This study was conducted to identify the quality and functional properties of meat and meat batter among commercial broilers and two different ages of spent layers. Breast and whole leg meat samples were prepared from the broilers and spent layers to compare meat quality traits: Commercial broiler (Arbor Acre; 6-week-old) and two different ages of spent layers (Hy-Line; 70 and 95-week-old). Three types of meat batters containing breast meat as 50% of total ingredients were also prepared to analyze processing qualities. The broiler showed the highest water holding capacity (p<0.05) and the lowest cooking loss value (p<0.05) in both meat and meat batter samples. The breast and leg meat of the 95-week-old layers showed the highest shear force value (p<0.05), and also showed the highest shear force and hardness values in the meat batter. Although the oldest layer meat showed tougher textural traits than the 70-week-old layers, no significant differences were found for cooking loss and water loss values in both the meat and meat batter samples. Besides, panelists gave equivalent scores within different ages and parts of the cooked layer meats in the sensory evaluation. Similar ratios of polyunsaturated fatty acids to saturated fatty acids, and omega-6 to omega-3 fatty acids were obtained from both the 70-week-old layer and 95-week-old layer meats. In conclusion, the 95-week-old spent layers, especially for breast meat, had equivalent potential as raw materials for processed meat products compared to the 70-week-old layers.

• Restorative Dentistry and Endodontics
• /
• v.28 no.3
• /
• pp.222-231
• /
• 2003

The purpose of this study was to compare shear bond strength and interfacial pattern of composite bond-ed to dentin using self-etching adhesive systems. Sixty extracted human molars with exposed occlusal dentin were divided into four groups and bonded with four adhesives and composites. Single Bond/Filtek Z 350(SB), Tyrian SPE-One-Step Plus/Aelitefil(TY), Prompt L-Pop/Filtek Z 250(LP), and One-Up Bond F/palfique Toughwell(OU). The results of this study were as follows; 1 Shear bond strength for OU was significantly lower than that of other groups(p＜0.05). No significant difference was founded among SB, TY, and LP. 2. Failure modes to dentin showed adhesive and mixed for SB TY and LP, but them for OU showed adhesive in all spceimens. 3. Dentin-resin interface showed close adaptation for SB, TY, and LP, but it showed gap for OU. 4. The hybrid layers for TY, LP OU were thinner than that of SB. Adhesive layers were observed between composite and hybrid layer, which were 5 $\mu\textrm{m}$ thick for TY and 10 $\mu\textrm{m}$ thick for OU.