• Journal of the Korean Society of Marine Environment & Safety
• /
• v.21 no.5
• /
• pp.538-542
• /
• 2015

The transverse moment of inertia is an indispensable factor in analyzing the roll motion characteristics of ships and the calculating method needs to be based on the more reasonable theories when deciding the value as the results and reliability of analysis could be much affected by the correctness. However, the mass distribution and shape of hulls are quite complicated and give much difficulties in case of calculating the value directly from the ship design data, furthermore even acquiring the detailed design data for calculation is almost impossible. Therefore some simpler ways are practically adopted in the assumption that the gyradius of roll moment can be decided by a given ratio and hull width. It is well known that the responses of the free roll decay are varied according to the value of roll moment in view of roll period and amplitude decay ratio, so that the general formula to get the moment value can be derived also from the observation of roll decay responses. This study presents how the roll period and decay ratio are interrelated each other from the roll motion characteristics with suggesting a general formula to be able to calculate roll moment from it. Finally, the obtained general formula has been applied to a ship data to check the resultant characteristics through analyzing graphs and showed that the roll moment becomes more accurate when rolling period and decay ratio are considered together in calculation.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.8
• /
• pp.781-787
• /
• 2011

We design a four-stage propane-refrigerant centrifugal compressor for an LNG plant. Using a commercial code, we aerodynamically designed the compressor at each design point of the corresponding stages. We estimated the one-dimensional aerodynamic design output and the three-dimensional shape of the impeller flow passage via three-dimensional flow analysis. In particular, we discuss in detail the flow characteristics of the impeller and the vaneless diffuser passages of the fourth-stage compressor in terms of the velocity fields, the pressure, and the entropy distributions of the flow passages. We include the flow effects of the tip clearance flow, because at this stage the rotating speed and total inlet pressure are higher than those at the other compressor stages are. We carried out performance tests of the designed compressor stages using propane as a refrigerant in the LNG cycle. The practical evaluation could lead to design enhancements in the future.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.3
• /
• pp.307-313
• /
• 2010

In this study, alternative designs for the bends used in district heating pipes are investigated. The district heating pipes, which are subjected to temperatures of 10 to $120^{\circ}C$ and a water pressure of $16\;kgf/cm^2$, have to withstand thermomechanical cyclic loads when in use. These pipes comprise three concentric tubes: a steel pipe (internal), polyurethane (PUR) insulator (middle), and a high-density polyethylene (HDPE) case (external). In addition, the bends in the district heating pipe system are covered with foam pads that cause aging. In this study, an alternative bend design that does not involve the use of a foam pad is proposed to overcome the aging problem in the bends. In the proposed design, "shear rings" are added to the surface of a bend, and its dimensions are determined by a combination of the statistical (Taguchi) method and FEM. The geometrical parameters such as thickness, height, and number of the rings significantly affect the design optimization, and hence, they affect the results of the FEM.

• Korean Journal of Plant Taxonomy
• /
• v.38 no.2
• /
• pp.79-91
• /
• 2008

Asplenium yoshinagae (Aspleniaceae), previously known only from Japan, southwest China to Himalaya, was found in Gageo-do, Heuksan-myeon, Sinan-gun, Jeollanam-do. This species is similar to A. trichomonas, A. tripteropus, A. boreale, A. normale and A. oligophlebium by having gemmae and auricle of pinna, and distinguished from the latters by distinct stipe length, stalk of pinna, acute apex of pinna, length of indusium and shape of sorus. The Local name, Ga-geo-kko-ri-go-sa-ri, was newly given considering the locality. To reveal the interspecific relationships within the genus Asplenium in Korea, cladistic analysis was performed for 22 taxa of Asplenium as ingroup and 2 taxa of Diplazium as outgroup from Korea based on 20 morphological characters. As the results, the genus Asplenium seperated strongly from outgroup, and divided into 4 clades. Asplenium yoshinagae belong to the third clade. A. hondoense N. Murtakami & S. I. Hatanaka, which contained in the second clade, had treated as Hymenasplenium, but this results supported that this taxon may be contained in Asplenium, and also, Asplenium ruprechtii, not in Comptosorus. The morphological characters and illustrations of the species are provided together with photographs of habitat.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.28 no.1
• /
• pp.47-58
• /
• 1998

The purpose of this study was to investigate an influence of the change of central panoramic curves on the image reconstruction in the dental implant CT. The author designed three experimental groups according to the location of central panoramic curve. In group A, central panoramic curve was determined as the curve connecting the center of roots from the first premolar to the first molar. In group B, central panoramic curve was determined as the line connecting the lingual cortical plate at the level of the mesial aspect of the first premolar with the buccal cortical plate at the level of the mesial aspect of the first molar. In Group C, central panoramic curve was determined as the line connecting the buccal cortical plate at the level of the mesial aspect of the first premolar with the lingual cortical plate at the level of the mesial aspect of the first molar. Twenty four reformatted CT images was acquired from four mandibles embedded in the resin block and twenty four contact radiographs of dog specimens were acquired. Each Image was processed under Adobe Photoshop program analysed by MSPA(mandible/maxilla shape pattern analysis) variables such as MXVD, MXHD, UHD, MHD, and LHD. The obtained results were as follows ; 1. The mean of MXVD variable was 19.9, 20.2, and 20.0 in group A, B, and C, respectively, which were smaller than actual value 20.5. But, there was no significant difference among 3 groups (p>0.05). 2. The mean of MXHD, UHD, MHD, and LHD variables in group A, B, and C was 11.9, 12.2, and 12.3; 9.3, 9.5, and 9.6; 10.0, 10.3, and 10.3; 9.2, 9.3, and 9.4 respectively which were equal to or greater than the actual value 11.8, 9.3, 10.0, and 9.2. But, there was no significant difference among 3 groups (p>0.05). 3. The number of noneffective observations with difference over or under 1 mm with comparison to the actual value was 24(20％), 58(48.3％), and 52(43.3％), respectively, in group A, B, and C. 4. In group A, the number of observations over 1 mm and under 1 mm was 9 and 15, respectively, but in group Band C, the number of observations over 1 mm was more than under 1 mm.

• Korean Journal of Environment and Ecology
• /
• v.26 no.4
• /
• pp.576-587
• /
• 2012

As being actual physiognomical vegetation on Daegwang sand dune in Imjado, the widest area is occupied by Pinus thunbergii community planted as windbreak forest whereas those communities such as Robinia pseudoacacia community, Elymus mollis community, Imperata cylindrica var. koenigii - Elymus mollis community, Carex kobomugi community, Ischaemum antephoroides community, Imperata cylindrica var. koenigii community, Phragmites communis community, Imperata cylindrica var. koenigii - Calamagrostis epigeios community occupy as band shape or patch. According to the result of the data collected and analyzed based on phytosociological method regarding 74 plots of survey area, the species composition of Daegwang sand dune vegetation is classified total 10 vegetation units comprises 7 communities and 5 groups. The 7 communities are classified into Pinus thunbergii community, Robinia pseudoacacia community, Rosa rugosa var. rugosa community, Ischaemum antephoroides community, Carex kobomugi community, Calamagrostis epigeios community, and the sub-units of Pinus thunbergii communities are classified into 3 groups of Pteridium aquilinum var. latiusculum group, Elymus mollis group, Pinus thunbergii topical group and the sub-units of Calamagrostis epigeios communities are classified into 2 groups of Phragmites communis group, Calamagrostis epigeios tipical group. The zonation of vegetation from coastal line indicated with the order of Elymus mollis - Carex kobomugi, Carex pumila, Lathyrus japonicus - Calystegia soldanella - Vitex rotundifolia, Lathyrus japonicus, Ischaemum antephoroides - Rosa rugosa var. rugosa. According to the analysis result of longitudinal section, it was found to be those types with wide width herbaceous vegetation of foredune, smooth slope of foredune, lots of dune ridges with no structure were less vulnerable to erosion of sand dune and advantageous to its recovery.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.26 no.1
• /
• pp.59-67
• /
• 2013

Complex-shaped tall building causes many structural challenges due to its structural characteristics regarding inclined members and complexed shape. This paper is aimed at development of design process using computational-platform which is effective design tool for responding frequent design changes, particularly as to overseas projects. StrAuto, a parametric structural modeling and optimizing system, provides the optimized alternatives according to design intent and realize a swift process converting a series of structural information necessary to nonlinear analytical models. The application of the process was to a 45-story hotel building in Ulanbator, Mongolia adopting shear wall and special moment frame with outrigger systems. To investigate the safety of lateral force resisting system against maximum considered earthquake(MCE), nonlinear response history analysis was conducted using StrAuto.

• Journal of Periodontal and Implant Science
• /
• v.35 no.2
• /
• pp.359-369
• /
• 2005

It has been suggested that morphologic characteristics of the periodontium are partly related to the shape and form of the teeth. Furthermore, the severity of symptoms of periodontal disease have been proposed to differ among these various morphologic entities or "biotypes". The purpose of the present study was to examine the relationship between the form of the crowns in the maxillary anterior tooth segment and (1) a group of morphological characteristics and (2) the thickness of the gingiva. The thickness of gingiva was measured by ultrasonic device(SDM). 100 subjects devoid of symptoms of destructive periodontal disease were examined regarding, e.g., probing depth, gingival recession, width of keratinized gingiva, thickness of the keratinized gingiva. From maxillary study cast, the width(at the apical third-CW) and the length(CL) of the crowns of the 6 anterior teeth were determined. A CW/CL-ratio was calculated for each tooth and averaged for each tooth region. The individual mean CW/CL-ratio values for the central incisors were ranked. The 10 subjects ranked highest and the 10 ranked lowest were selected as having either a long-narrow(group N) or a short-wide(group W) form of the crown of the tooth. The data for each of the examined parameters were averaged for each tooth region in each subject and mean values for subjects in groups W and N were compared using the Student t-test. Stepwise multiple regression analysis, including data from the whole sample, was performed for each tooth region with the thickness of the free gingiva as the dependent variable. The results from the analyses demonstrated that individuals with a long-narrow form of the central incisors displayed, compared to individuals with a short-wide crown, form (l) a narrow zone of keratinized gingiva, (2) a pronounced "scalloped" contour of the gingival margin. There was no significant difference between groups N and W with respect to the thickness of the keratinized gingiva. The CW/CL-ratio data revealed that a certain form of the crowns in the central incisors was accompanied by a similar form in the lateral incisors and canine tooth region. The regression analyses demonstrated that the thickness of the keratinized gingiva in central, lateral incisors and canines was significantly related to the width of the keratinized gingiva.

• The Journal of Korean Academy of Prosthodontics
• /
• v.41 no.3
• /
• pp.319-324
• /
• 2003

Statement of problem. Adhesives in dentistry playa major role in the success of restorative treatments. In the treatment of all ceramic restoration it is needed to find the adequate bond strength between enamel and dentin. Purpose. The purpose of this study was to evaluate shear bond strength of resin cement bonded to extracted human uncut enamel, cut enamel, and dentin in vitro. Material and methods. Ten freshly extracted anterior teeth without any previous restorative treatments were chosen. The extracted teeth were embedded in PMMA cold acrylic in the shape of a cylinder, 25 mm in diameter by 25 mm in height. The bonding system used was as follow: Uni-Etch (32% phosphoric acid), One-Step adhesive, Duolink resin cement. The specimens were acid etched and rinsed with water. Two layers of One-Step adhesive were coated with a disposable brush on the uncut enamel. VIP curing light at $500mV/cm^2$ was used to cure the adhesive. For cut enamel shear bond test, the specimen used for uncut enamel was further reduced approximately $0.3{\sim}0.5mm$ using a laminate preparation diamond bur (0.3 mm in depth). The specimens were subsequently treated with 320-grit SiC paper followed by 600-grit SiC paper and cleaned with distilled water. The bonding procedure on the cut enamel was same as uncut enamel bonding procedure. For dentin bonding test, the specimen used for cut enamel was further reduced approximately $0.5mm{\sim}1.0mm$ using a laminate preparation diamond bur (0.5 mm in depth of diamond cutting). The amount of reduction was evaluated with the silicone mold. The specimens were subsequently treated with 320-grit SiC paper followed by 600-grit silicon carbon paper and cleaned in distilled water. The bonding procedure on the dentin was same as uncut enamel bonding procedure. All samples were mounted and secured on the Ultradent shear bond test sample holder, and Ultradent restricted shear bond testing device was used with Universal Instron machine until fracture. Analysis of variance (ANOVA) test was performed comparing the result at P<0.05. Multiple comparison (Tukey) was used to compare each groups. Result. The result showed that the mean value in shear bond strength of resin cement bonded to uncut enamel, cut enamel and dentin were 27.04 Mpa, 30.25 Mpa and 26.39 Mpa with respect. Conclusion. Within the limitation of this study, the mean value of the shear bond strength of cut enamel was higher than those of uncut enamel or dentin. However there existed no statistical differences between three different human dentition substrates due to increased adhesive characteristics.

• Polymer(Korea)
• /
• v.32 no.3
• /
• pp.193-198
• /
• 2008

Sibutramine is a highly crystalline and poorly water soluble drug as the appetite depressant for obesity treatment. In order to increase water solubility of sibutramine, microspheres including sibutramine were prepared by solid dispersion method using a spray dryer. The crystallinity and morphology of the prepared microspheres were confirmed by SEM and XRD. The morphology of micro spheres has gradually changed into spherical shape as increasing evaporation rate of solvent. According to XRD analysis, crystallinity of sibutramine in micro spheres was decreased by below 10%. Release behavior of microspheres was investiaged at pH 1.2, pH 6.8, and solubility of the sibutramine was significantly different depending on pH. The hard capsule showed fast release of sibutramine comparing with the tablet. These results demonstrated that the pharmaceutical preparation is able to control the release behaviors.