• Journal of the Korean GEO-environmental Society
• /
• v.4 no.4
• /
• pp.35-43
• /
• 2003

In this study, the physical and chemical characteristics of incinerated pulp and sewage sludge ashes for recycling and reuse were examined. Then we studied the application to the cement admixture by pozzolanic reaction. The particle size of incinerated pulp and sewage sludge ashes was distributed around $10{\sim}100{\mu}$, and the contents of $SiO_2$ and $Al_2O_3$ were 45.8~51.0%, respectively. Compressive strengths of the solidified ashes were relatively higher, when the content of substituted incineration ashes was 10% and the porosity was also lower except for the case of sewage sludge ash. As results, it is shown that it may be possible to recycle incinerated pulp sludge ashes as cement admixtures.

• Journal of Korean Society on Water Environment
• /
• v.34 no.3
• /
• pp.316-327
• /
• 2018

Liquid fertilizers made from livestock manure contain high concentrations of nitrogen and phosphorus and thus are used as a fertilizer. However, excessive use of liquid fertilizer causes eutrophication of agricultural land and nonpoint source pollution. In this study, as a means of lowering the nutrient concentrations, struvite ($MgNH_4PO_4{\cdot}6H_2O$) production from the liquid fertilizer was investigated. When liquid fertilizers produced in Gyeonggido were analyzed, its characteristics differed by region and season, but the phosphorus concentration was commonly lower than that of nitrogen. When $K_2HPO_4$ and $MgCl_2$ were added to the liquid fertilizers, the optimal pH for struvite formation was pH 9.5. For environmentally friendly sources of magnesium and phosphate, ferronickel slag (FNS) and sewage sludge ash (SSA) were suspended in deionized water and extracted by sulfuric acid with various mass ratios. The optimum conditions for extracting FNS and SSA were 4.0 M sulfuric acid and 0.35 mass ratio of sulfuric acid to sewage sludge ash, respectively. For forming struvite, 0.233 L of SSA leachate (SSAL) was added into 0.3 L of liquid fertilizer containing 2,586 mg/L of ammonia and 110 mg/L of phosphate, pH was then adjusted to pH 9.5 using 10 M of NaOH. Afterwards 0.333 L of FNS leachate (FNSL) was added to this mixed solution. After a reaction for 1 hr at room temperature, the remaining concentrations of magnesium, ammonium, and phosphate were less than 50 mg/L, 500 mg/L and 150 mg/L, respectively, and 30 g of precipitates were obtained, most of which were struvite.

• Journal of Korean Society of Water and Wastewater
• /
• v.32 no.2
• /
• pp.131-143
• /
• 2018

Phosphorus (P) is a limited, essential, and irreplaceable nutrient for the biological activity of all the living organisms. Sewage sludge ash (SSA) is one of the most important secondary P resources due to its high P content. The SSA has been intensively investigated to recover P by wet chemicals (acid or alkali). Even though $H_2SO_4$ was mainly used to extract P because of its low cost and accessibility, the formation of $CaSO_4$ (gypsum) hinders its use. Heavy metals in the SSA also cause a significant problem in P recovery since fertilizer needs to meet government standards for human health. Therefore, P recovery process with selective heavy metal removal needs to be developed. In this paper some of the most advanced P recovery processes have been introduced and discussed their technical characteristics. The results showed that further research is needed to identify the chemical mechanisms of P transformation in the recovery process and to increase P recovery efficiency and the yields.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.29 no.1
• /
• pp.5-17
• /
• 2021

This study is a literature review on the recovering phosphorus from Incinerated Sewage Sludge Ash(ISSA), which has relatively high content of phosphorus. Experimental conditions and influencing factors related to the recovery of P and removal of heavy metals by wet and thermochemical methods were discussed. For the practical application of the recovery of P from ISSA, an integrated process linked to incineration facilities is required in terms of economy from the perspective of the entire system including disposal of wastewater and residues generated during the recovery process, and minimizing added chemicals and energy consumption.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05b
• /
• pp.157-160
• /
• 2005

The purpose of this study is to efficiently treat the sewage sludge discharged from sewage treatment plants and evaluate the feasibility of the manufacture of lightweight aggregates(LWA) using a large quantity of sewage sludge and inorganic waste binder ;f1y-ash, waste-stone, tailing, phosphogypsum. Then they were burned in different soak temperatures from 1190$^{circ}C$ to 1290$^{circ}C$ with fixed soak time and heating rate at 5 minutes and 20$^{circ}C$/min respectively in order to produce lightweight aggregate (LWA). Experiment were generated to evaluate the quality of LWA as well as the relationship between burning condition and product's quality.

• Clean Technology
• /
• v.24 no.4
• /
• pp.323-331
• /
• 2018

The results of an experimental investigation on the co-firing characteristics and slagging behavior of dried and hydrothermal carbonization sewage sludge, sub-bituminous coal, and wood pellet in a fluidized bed were presented. Combustion tests were conducted in a lab-scale bubbling fluidized bed system at the uniform fuel-air equivalence ratio, air flow rate, and initial bed temperature to measure bed temperature distribution and combustion gas composition. 4 different fuel blending cases were prepared by mixing sewage sludge fuels with coal and wood pellet with the ratio of 50 : 50 by the heating value. $NO_x$ was mostly NO than $NO_2$ and measured in the range of 400 to 600 ppm in all cases. $SO_2$ was considered to be affected mostly by the sulfur content of the sewage sludge fuels. The cases of hydrothermal carbonization sewage sludge mixture showed slightly less $SO_2$ emission but higher fuel-N conversion than the dried sewage sludge mixing cases. The result of fly ash composition analysis implied that the sewage sludge fuels would increase the possibility of slagging/fouling considering the contents of alkali species, such as Na, K, P. Between the two different sewage sludge fuels, dried sewage sludge fuel was expected to have the more severe impact on slagging/fouling behavior than hydrothermal carbonization sewage sludge fuel.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.31 no.2
• /
• pp.53-61
• /
• 2023

Most of the sewage sludge is organic waste containing a large amount of organic substances decomposable by microorganisms by biological treatment. As for existing sewage sludge treatment methods, reduction and fuel conversion are being carried out using technologies such as drying, incineration, torrefaction, carbonization. However, the disadvantage of high energy consumption has been pointed out as latent heat of 539 kcal/kg is consumed based on drying. Therefore, in this study, we intend to produce solid fuel through hydrothermal carbonization(HTC), which is a thermochemical treatment. To evaluate the value of solid fuel, the characteristics of carbonization and fuel ratio were analyzed. As a result, as the hydrothermal carbonization reaction temperature increased, the lower heating value also increased by about 500 kcal/kg due to the increase in the degree of carbonization. H/C, O/C, ratio showed a decreasing trend from 1.78, 0.46 to 1.57, 0.32. When the ratio of ash to combustible content (fixed carbon + volatile) of dry sludge was 0.25 or more, it was derived that the degree of carbonization and calorific value did not increase even when hydrothermal carbonization was performed.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.6
• /
• pp.659-665
• /
• 2008

This study is about zeolite synthesis from the sewage sludge incinerator fly ash of "S" sewage treatment center located in Seoul. For this purpose, the properties of raw fly ash as starting material, the hydrothermal conditions for zeolite synthesis and the environmental applicabilities of synthesized zeolites were examined. Fly ash from sewage sludge incinerator has large quantities of SiO$_2$ and Al$_2$O$_3$ and their contents are 42.8 wt.% and 21.2 wt.% respectively. So fly ash is considered to be possible starting material for zeolite synthesis. The results from leaching test of fly ash showed that the concentration of hazardous metals were very low as compared with the Korea leaching standard of the Waste Management Law. But the concentration from total recoverable test of fly ash were higher than the fertilizer standard of Fertilizer Management Law. Major zeolite products synthesized by hydrothermal reaction are analcime in teflon vessel and zeolite P1 in borosilicate flask. Optimum conditions for the synthesis of analcime were 1 N of NaOH concentration, 16 hour of reaction time and 135$^{\circ}C$ of reaction temperature. For the zeolite P1 formation, the proper conditions were demonstrated to be 5 N of NaOH concentration, 16 hour reaction time and 130$^{\circ}C$ of reaction temperature in this study. Hazardous metal contents in the analcime product are similar with those in raw fly ash. In case of the zeolite P1, the contents are reduced to nearly a half. Raw fly ash and the analcime product showed NH$_4{^+}$ ion exchange capacity of 0$\sim$1.0 mg of NH$_4{^+}$g$^{-1}$ and 3.0$\sim$7.4 mg of NH$_4{^+}$g$^{-1}$, respectively. However, the zeolite P1 product reached exchange capacity to 14.6$\sim$17.8 mg of NH$_4{^+}$g$^{-1}$. This values are in the range of those of natural clinoptilolite and phillipsite. From this point of view, zeolite synthesis from sewage treatment sludge incinerator fly ash is a good alternative for solid waste recycling.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.9
• /
• pp.857-861
• /
• 2010

Recently photochemical smog has become a serious urban air pollution. And VOC is the major pollutant for it. With the advance of industrialization and urbanization, MSWI fly ash and sewage sludge and melting slag were generated. It is necessary to de-toxificate ashes, because they contain many toxic constituents and probably lead to contaminate the environment. The objective of this research was to prepare multi-functional brick which is able to remove VOCs in ambient air. The bricks were made of MSWI fly ash, sewage sludge and slag. The benzene adsorption experiment by brick was acted to evaluate its adsorptivity. And also photocatalyst material was coated to enhance its adsorptivity and the endurance on the brick. According to the result, the benzene showed 74~96%. The removal efficiency was increased and the breakpoint time was lengthened by coating a brick.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.2
• /
• pp.114-118
• /
• 2009

With the advance of industrialization and urbanization, a lot of waste has been discharged and treated by incineration. But fly and bottom ashes are generated in this process. In addition, the treatment method to recycle sewage sludge and melting slag is required to manage these wastes. The objective of this research was to prepare of multi-functional brick which were made from MSWI (Municipal solid wastes incinerator) fly ash, sewage sludge and slag. The bricks were made by mixing raw materials and then drying for 24 hours. Next, they were dried for 24 hours at $160^{\circ}C$ and fired for 2 hours. Calcination temperature was changed to discuss the effect of temperature from $1,080^{\circ}C$ to $1,130^{\circ}C$. Compressive strength of a brick was creased with the increase of temperature. To increase mixing ratio of fly ash and slag reduce the compressive strength the optimal condition was the mixing ratio of fly ash : melting slag : sewage sludge : clay as 10 : 20 : 5 : 65 and $1,150^{\circ}C$ of calcination temperature. Compressive strength was obtained as about 41 MPa at this condition.