• Journal of Sensor Science and Technology
• /
• v.26 no.5
• /
• pp.324-330
• /
• 2017

In this paper, the automation of sweeping center setting for wavelength swept laser used in SS-OCT has implemented. For 3 regions where the initial FFP-TF pass wavelength can be located, each different DC voltage pattern is applied to FFP-TF. Through its performance test to the laser, fast and exact setting to sweeping central wavelength, flat sweeping with ${\pm}0.5dB$ fluctuation range, and 10 mW average optical power were obtained. This shows that the realized automatic setting process can replace an inconvenient manual setting operation used for current wavelength swept laser. Additionally it cuts costs for optical spectrum analyzer necessary to laser spectrum monitoring.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.11a
• /
• pp.129-130
• /
• 2022

This study is conducted to identify improvements in the setting time estimation system through the Mock-up test of the finishing automation system and the setting estimation system. As a result of the study, it is necessary to adjust the spring strength of the setting time estimator and the diameter and length of the estimation needle so that the value of the hardness can be measured from 15HD to around 40HD.

• Journal of Information Technology Applications and Management
• /
• v.27 no.6
• /
• pp.101-116
• /
• 2020

This study attempts to derive critical success factors and prioritize activities for implementing the automation of software test. Software testing proceeds in five steps of test plan, test case design, test scripting & test environment setup, test execution & evaluation, and test closure. From the literature, twenty influence factors in the five steps were identified. Focus Group Interviews with ten experts in software testing selected fourteen factors on the basis of importance and feasibility. Some factors were further divided to clarify their meanings and the number of influence factors finally became twenty one. A survey on the influence factors was conducted with 75 IT professionals. An importance-feasibility analysis was applied to the survey responses and classified the influence factors into four groups of essential factors, critical factors, low priority factors, and minimal factors. Essential factors include objectives for test automation, strategies for test automation, test automation training, test automation education, setting up test automation environment, setting up test environment, test automation tool selection. Critical factors include management's continued support, management's continued interest, role of automation engineers, and skills of automation engineers. This result suggests that a lot of efforts should be put into SW test plan for the successful SW test automation and SW automation should proceed in consideration with the priorities and resource consumption.

• 제어로봇시스템학회:학술대회논문집
• /
• 1995.10a
• /
• pp.538-541
• /
• 1995

In steel works, reheating furnace is an essential part of a rod mill plant and it treats various types of billets continuously. Although getting an optimal setting for a single billet is simple, control setting for whole groups of billets is a difficult task. In this work, we studied a detail mathematical model and optimal control setting of reheating furnace. As the mathematical model of each billet is a partial differential equation, on-line control is almost impossible for the whole billets charged into the furnace. Therefore, we tried to provide a guideline for optimal setting value of the roof(index) temperature for the target billets which account for about 20% of the charged billets.

• Proceedings of the KIEE Conference
• /
• 1998.11a
• /
• pp.211-213
• /
• 1998

This paper introduces the additional remote monitoring and remote setting functions needed to operate the distribution automation system effectively. we compare the additional functions with the old functions. The remote setting of minimum trip value of fault indicator is an example of additional function. It saves time and line-man's power. Also this paper describes the data transmission flow diagram for operation of distribution automation system using wireless communication method.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.52 no.8
• /
• pp.444-449
• /
• 2003

In this paper present Autonomous Adaptive Digital Over Current Relay for distribution networks which acts autonomous setting using the short circuit impedance measured by relay of power systems. Automation of relay setting is one of the basic requirements for distribution automation, although manual relay setting is used at present. The short circuit impedance from a power source in distribution networks essential for the Autonomous Relay Setting changes frequently in distribution networks. In this paper the short circuit impedance is calculated with voltage and current measured in real time operation of digital relay using the Recursive Least Squares. A new method of digital relay setting is introduced using the the short circuit impedance and load current.

• Proceedings of the KIEE Conference
• /
• 2002.07a
• /
• pp.6-8
• /
• 2002

In this paper present Autonomous Adaptive Digital Over Current Relay which acts autonomous setting using voltage and current measured by relay in the change of power systems. Automation of relay setting is required for distribution automation although manual relay setting is used at present. This paper presents Autonomous Relay Setting which knows change of the power system and acquires setting element using the Recursive Least Squares. Relay setting is very difficult work. But proposed relay is expected to decrease burden of relay setting using acquired information of power system change and autonomous setting. Also fast protective ability is expected according to change of power system.

• Design & Manufacturing
• /
• v.16 no.1
• /
• pp.21-26
• /
• 2022

In the CNC machining process, problems such as lowering of machine operation rate, setting errors, and machining precision occur due to the increase in setting time and preparation time. These machining errors cause delays in delivery and increase in cost due to an increase in the number of mounting and dismounting of the workpiece, an increase in measurement and reprocessing time, and an increase in the finishing time in the assembly process. Therefore, in this study, by automating the setting of the work piece using OMV (On Machine Verification), which is a meteorological measurement system, the preparation time for machining the work piece and the setting accuracy were improved, the rework rate was reduced, and the mold manufacturing process was shortened. Through the advancement, standardzation, and automation of the mold part manufacturing process, we have improved productivity by minimizing low-value-added repetitive tasks. In addition, the measurement time was reduced by more than 50% and the machining measurement rate was improved by more than 20%, eliminating repetitive work for correcting machining defects, and reducing the work preparation time by more than 15% through automatic setting.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.38 no.4
• /
• pp.202-211
• /
• 2015

Companies build the factory automation system to improve management effectiveness and productivity as prime strategies for sustainable growth. But most companies undergo various trials and errors while carrying out the project without elaborate preparation stage for factory automation. In this study, we tried to verify what factors are critical to effectively building distribution automation system, which is a branch of factory automation system. A consulting model for setting up a Material Handling Automation System by utilizing the Stage-Gate Process, which is product development process was studied. 29 material handling automation projects carried out between the year 1990 to 2013 at K-Company were selected. Interviews with the project managers, operators and maintenance personnels, various records and current status of the projects were used as data for structural equations based on the Milan consulting model and existing researches of factory automation, CIM for material handling automation. Creating effective basis of production, material handling system and energy saving system with expert review, when preparing a material handling automation project, help promote the project planning thus contributing to the performance of the resulting system, which appears though rather weakly in our data. Also the effect of material handling automation can be enhanced through sufficient and effective links to the relevant environments such as production logistics management and automated warehouses. More detailed planning characteristics of project promotion or some time-series data of effective Material Handling Automation System could enhace furthur studies. We propose a consulting model for setting up an efficient material handling automation system.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.11a
• /
• pp.17-18
• /
• 2023

This study aims to compare the hardness value development characteristics according to the water-cement ratio during a series of experiments to develop a setting estimator for an AI-based concrete finishing automation system. For the test variables, water-cement ratios are varied with 30, 40 and 50%. Proctor penetration test and surface hardness test by setting time estimator are conducted to estimate the setting time. For the effect of water-cement ratios, they did not affect the surface hardness either, while initial set time and final set time are not constant with water-cement ratios.