• 한국기계가공학회지
• /
• 제12권5호
• /
• pp.170-175
• /
• 2013

For this study, the domestically developed bootstrap reservoir of the aircraft is set up in accordance with the temperature and humidity conditions depicted on the qualification test, and the variation in the internal pressure of the bootstrap reservoir of the aircraft is examined. The study shows that the bootstrap reservoir has less variation in the internal pressure at room temperature than at low temperature($-40^{\circ}C$). As a result, the internal pressure can be maintained stably when the temperature of working fluid in the bootstrap reservoir and the atmosphere environment is over room temperature($25^{\circ}C$). Therefore the keeping of temperature above room temperature is very important to operate the bootstrap reservoir of the aircraft properly.

• 대한물리치료과학회지
• /
• 제24권2호
• /
• pp.17-26
• /
• 2017

Purpose: The importance of core exercise on muscle activation of the lower extremity has been studied. This study investigated the effects of core exercise using pressure biofeedback unit on muscle strength of lower extremity. Method: Fourteen healthy young adults (7 males and 7 females) were recruited. They were randomly separated two groups and performed core exercise using pressure biofeedback unit of one set for three minutes, 10sets per day for three weeks. Result: The mean of muscle strength of lower extremity, maximum power of muscle and peak TQ/BW in core exercise group significantly increased after core exercise using bio feedback unit (p<.05). Conclusion: These findings suggest that core exercise using pressure biofeed-back unit may help improving of muscle strength of lower extremity in young adults.

• 한국자동차공학회논문집
• /
• 제5권3호
• /
• pp.202-208
• /
• 1997

The knocking is one of major parameters to improve engine performance in a spark ignition engine. Many researches have been carried out to identify them using cylinder pressure, vibration signal and so on. In the present study, measurement and analysis was conducted to set up the criteria of knock occurrence by using microphone signal. Cylinder pressure was measured for the reference signal of knocking. It has been observed that resonance frequencies of pressure wave are nearly independent of engine operating conditions such as engine speed, air fuel ratio, load and octane number of fuel within to limited experimental conditions. SDBP(sum of different band-pass data) method using resonance frequency of knock was proposed for estimating knock intensity. SDBP method is superior to identify knock occurrence and its intensity in case of sound pressure measurement.

• 대한물리치료과학회지
• /
• 제9권1호
• /
• pp.159-166
• /
• 2002

The purpose of this study was to review the knowledge related to historic background, causes, symptoms, etiology and rehabilitation methods related to this disease and suggest some ways to reduce complications from it. The importance of underwater pressure disease was not emphasized, therefore, there is a need for continuous research on treatment methods and prevention for it. As one goes into the deeper water, they will be affected by the hydraulic pressure rather then the atmospheric pressure, and it will be increased 1mmHg by 10meters. Underwater pressure disease can be occurred when one comes out of deeper water too quicked. This results the imbalance of the composition rate of nitrogen in blood. However, there is not enough facilities to treat this disease and these facilities are located in limited areas. Therefore, there is an urgent need to set up a medial center that is specialized in prevention and treatment of underwater pressure disease.

• 대한전기학회논문지
• /
• 제39권11호
• /
• pp.1227-1234
• /
• 1990

This study is to figure out the properties of the DC thermal plasma at low pressure. For this purpose, a temperature measurement system utilizing emission spectroscopy has been set up and its measurement method and results have been described. At low pressure, the plasma has shown drastic changes in its appearance. The discharge characteristics under low pressure have been measured and analyzed. The temperature of thermal plasma generated in this research has been ranged from 10, 000 K to 15, 000 K. Temperature has been observed to increase with the flow rate and magnetic field strength. The temperature characteristics at low pressure has been observed to coincide with the reported results.

• 연구논문집
• /
• 통권30호
• /
• pp.129-135
• /
• 2000

Double boss type composite pressure bottles have been developed widely but single boss type had not because there are some difficulty in technical point. In this paper a research was performed to develop composite pressure vessel in conjunction with design, fabrication, and test. Fiber pattern and angles were decided by CADFIL software and they are [liner/$15^{\circ}$/$15^{\circ}$/$90^{\circ}$/$18^{\circ}$/$90^{\circ}$/$21^{\circ}$/$21^{\circ}$/$90^{\circ}$]. Fabrication of bottles was done by AEA's 5-axis filament winding machine. During fabrication fiber optic sensor were embedded to measure were behavior of structure at the applied internal pressure. Even though satisfied test results were not obtained, the experimental set-up of fiber optics showed the possibility for the application of filament wound vessels. However, the conventional strain and fabrication of single boss composite bottles.

• 한국광학회지
• /
• 제24권5호
• /
• pp.279-286
• /
• 2013

Brillouin spectroscopy has been widely used for the investigation of acoustic properties of condensed matters in the hypersonic region. A high-pressure Brillouin spectrometer was set up by combining a diamond anvil cell and a tandem multi-pass Fabry-Perot interferometer. It was successfully applied to liquid ethanol, and the pressure dependence of the sound velocity, the refractive index and other acoustic properties were derived based on the measurements. The detailed optical setup and experimental procedure are described.

• 한국소음진동공학회논문집
• /
• 제24권11호
• /
• pp.883-889
• /
• 2014

Mufflers have been widely used in the exhaust system to reduce the noise. However, installing muffler may deteriorate the efficiency due to the increase of back pressure. Mufflers usually consist of partition plates and perforated holes in a expansion chamber. In this paper, the influences of the location of the partition and hole on the acoustic TL and back pressure were examined. The acoustic TL was predicted using virtual lab commercial software, while the back pressure were predicted using CFX commercial software. The results were used to set up a database for finding their trends. The optimal muffler model in user-interested frequency range could be selected by analyzing this database.

• Steel and Composite Structures
• /
• 제51권2호
• /
• pp.139-151
• /
• 2024

In this research, a semi-analytical solution is presented for computing mechanical displacements and thermal stresses in rotating thick cylindrical pressure vessels made of functionally graded material (FGM). The modulus of elasticity, linear thermal expansion coefficient, and density of the cylinder are assumed to change along the axial direction as a power-law function. It is also assumed that Poisson's ratio and thermal conductivity are constant. This cylinder was subjected to non-uniform internal pressure and thermal loading. Thermal loading varies in two directions. The governing equations are derived by the first-order shear deformation theory (FSDT). Using the multilayer method, a functionally graded (FG) cylinder with variable thickness is divided into n homogenous disks, and n sets of differential equations are obtained. Applying the boundary conditions and continuity conditions between the layers, the solution of this set of equations is obtained. To the best of the researchers' knowledge, in the literature, there is no study carried out bi-directional thermoelastic analysis of clamped-clamped rotating FGM thick-walled cylindrical pressure vessels under variable pressure in the longitudinal direction.

• 한국운동역학회지
• /
• 제28권3호
• /
• pp.165-173
• /
• 2018

Objective: The purpose of this study is to provide biomechanical basis data for the analysis of the maximum vertical ground reaction force, the maximum plantar pressure, the average plantar pressure, and the contact area according to the type of the insole through the insole insertion type foot pressure gauge. Method: In the treadmill, the slope was set at 10%, the first type A was worn at a walking speed of 3.5 km / h, and then walking was carried out using B, C, and D types. Data from 20 boots with consistent walking were extracted and plantar pressure data were collected and analyzed. Results: Functional insole was more effective than conventional insole for maximum vertical ground reaction force, maximum plantar pressure, average plantar pressure, and contact area at 10% of treadmill ramps. Conclusion: In this study, D-type insole supports the cushion in the middle part and supports the heel cup with hardness in the hind part, so that it is the most effective insole by lowering the plantar pressure and dispersing it more widely.