• Journal of the Institute of Convergence Signal Processing
• /
• v.3 no.4
• /
• pp.42-48
• /
• 2002

The case that cannot show the satisfactory control results with a modeling error and a shortage of related knowledge about a plant is if a fuzzy controller designed based on the plant model or the experience applies to an actual plant. We must adjust the scale factor which is a controller again in order to improve control performance in case of this and needs a lot of time and costs because this regulation process is carried out with a trial and error way We proposes the fuzzy controller that an automatic control adjust scale factors according to fuzzy logic and normalizer in this paper We confirmed that an automatic adjusted fuzzy controller displayed good performance than the fuzzy controller that scale factors was fixed through simulation. We implemented the controller using the DSP processor and applied in a hydraulic servo system. And then we observed an experimental results.

• Proceedings of the KIEE Conference
• /
• 2008.04a
• /
• pp.73-74
• /
• 2008

In this study, we developed a robotic gait trainer which induces the active gait training based on predefined continuous proper lower extremity joint movements. AC servo motors and linear actuators were used to control hip and knee joints of patients and the weight support system was used to support the patient's weight during the gait training. We also implemented a Gill program to set the gait training pattern with several training parameters and to confirm states of patients and the system through the visual feedback. The effectiveness of the gait training system will be determined by the long-term clinical experiments in the future. We expect that the developed robotic gait training system could be applied very practically to recover gait abilities for persons with gait disorder.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1901-1905
• /
• 2004

A controller designed by CDM for a servo type system which is an augmented system constructed from a rotational inverted pendulum with an integrator added to its arm, is presented in this paper. In order to be able to apply the CDM concept, the augmented system must be linearized and converted into controllable canonical form. Then, the controller consisting of the state feedback gain matrix and an integral gain in the sense of CDM can be obtained. This shows that design procedure for the proposed controller is easy. The experimental results obtained from the rotational inverted pendulum controlled by the proposed controller show that the system response has no steady-state error, however, the oscillation amplitude of the arm angle is still significant. Therefore, in this paper, the friction compensation using Coulomb friction with stiction is also added to the controller. The oscillation amplitude of the arm angle that can be reduced remarkably is also shown in the experimental results.

• Journal of the Korea Convergence Society
• /
• v.7 no.1
• /
• pp.9-15
• /
• 2016

In this paper, we describe the design of a high speed data acquisition system(DAS) with STM32 processor based on Cortex-M4. The system is used for the sensor devices to collect raw data on production lines at factory and send them to the servo computer in real time. The system is designed for multi functions with universal asynchronous receiver and transmitter(UART), analog to digital converter(ADC), digital to analog converter(DAC), and general purpose input output(GPIO). those are well tested for various data acquisition and high speed motor control in real time.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.625-631
• /
• 2002

In the previous study, a polishing robot system was developed to automate the polishing process and to cope with the shortage of skilled workers. This polishing robot system has several advantages: reduced time for setting polishing work, decreased labor costs, effective operation, continuous polishing work without an operator, improved machine accuracy, and the ability to polish a free curved surface die. However, still the problem remains that a worker must stay to monitor the polishing process in the poor working conditions for a long time. Nowadays some advanced manufacturing companies need to find a way to check the performance of their production equipments and plants from remote sites. Thus, this study constructed the communication network and developed the monitoring programs (a servo program and a client program) to operate the polishing robot from remote sites. Using these programs, workers are able to monitor and control the polishing robot on the web page, in any place where internet service is possible. To guarantee a stable operation in spite of a variable computer operating environment, the monitoring system is implemented in Java. The experimental results showed that the developed monitoring programs provided a stable communication.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.170-172
• /
• 2003

Among low power servo applications, classical DC motors are very popular because they are reasonably cheap and easy to control. The main disadvantage is the mechanical collector which has only a limited life period. Also, brush sparking can destroy the rotor coil, generate EMC problems. So permanent magnet brushless do motors and drives are being used increasingly in a wide range of applications. This has been made possible with the advantages of high performance permanent magnets with high coercively and residual magnetic, which make it possible for the PM to have superior power density, torque to inertia ratio and efficiency, when compared to an induction or conventional dc machine. This paper presents the design of a PM brushless dc motor drive simplistically operates as a classical dc motor. The BLDC motor drive system for this paper composes to the power integrated circuits, the one chip device. And several simple semiconductors add to drive system for a motor drive system simplistically operates as a conventional dc motor. Test results confirmed the feasibility of the proposed motor drive system design.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.5
• /
• pp.792-799
• /
• 2017

The real time unmanned monitoring system of an equipment's internal parts and condition requires the monitoring device to be able to stop at a set location on the rail. However, due to the slip between the driving surface and the roller, an error occurs between the actual position and the command position. In this paper, a method to compensate the position error due to the roller slip is proposed. A proximity sensor located at both ends of the rail detects the starting point and the maximum position pulse, linearly compensating the error between the angular position of the motor and the mechanically fixed starting and maximum position pulse of the rail in forward and reverse direction. Moreover, unlike the existing servo position controller, the motor adopts the position detection method of Hall sensor in BLDC (Brushless DC) and applies an algorithm for low-speed driving so that a stable position control is possible. The proposed rail guided unmanned monitoring system with driving slip compensator was tested to verify the effectiveness.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.10a
• /
• pp.375-381
• /
• 2004

Recently, the evolution in production techniques (e.g. high-speed milling) and the complex shapes involved in modem production design has been increasingly popular. The key to the achievement is a drastic improvement of the dynamic behavior of the machine tool axes used in production machinery. The more complex these tool paths the higher the speed and acceleration requirements. But it is very difficult to reach the target for high speed machine tool because of the limitations of servo system and motion control system. However the direct drive design of machine tool axes, which is based on linear motors and which recently appeared on the market, is a viable candidate to meet the ever increasing demands, because of these advantages such as no backlash, less friction, more mechanical simplicity and very higher acceleration and velocity comparing to the traditional system. This paper focused on the performance tests of the high speed horizontal machine tool based on linear motor. Especially, dynamic characteristics were investigated through circular test and circular form machining test is carried out considering many important parameter. Therefore these several experiments is used to be evaluated the model for prediction of circular motion error and circular machined error.

• Smart Structures and Systems
• /
• v.25 no.5
• /
• pp.569-580
• /
• 2020

The identification of delays and delay compensation are critical problems in real-time hybrid simulations (RTHS). Conventional delay compensation methods are mostly based on the assumption of a constant delay. However, the system delay may vary during tests owing to the nonlinearity of the loading system and/or the behavioral variations of the specimen. To address this issue, this study presents an adaptive delay compensation method based on a discrete model of the loading system. In particular, the parameters of this discrete model are identified and updated online with the least-squares method to represent a servo hydraulic loading system. Furthermore, based on this model, the system delays are compensated for by generating system commands using the desired displacements, achieved displacements, and previous displacement commands. This method is more general than the existing compensation methods because it can predict commands based on multiple displacement categories. Moreover, this method is straightforward and suitable for implementation on digital signal processing boards because it relies solely on the displacements rather than on velocity and/or acceleration data. The virtual and real RTHS results show that the studied method exhibits satisfactory estimation smoothness and compensation accuracy. Furthermore, considering the measurement noise, the low-order parameter models of this method are more favorable than that the high-order parameter models.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.12
• /
• pp.2386-2391
• /
• 2011

Tracking and detecting targets by the millimeter wave seeker is affected by moving of platform. In order to perform the tracking performance, stabilization of a millimeter wave seeker which consists of 2-axis gimbals was considered in this study. The feasibility of the analysis and the 2-axis gimbal servo system modeling design were verified along with some simulation results.