• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.2
• /
• pp.109-117
• /
• 2015

Aircraft needs an inlet duct to supply the airflow to engine face. A fighter aircraft that requires low radar observability has to hide the engine face in the fuselage to reduce the Radar Cross Section(RCS). Therefore, the flow path of the inlet duct is changed into S-shape. The performance of the aircraft engine is known to be influenced by the shape and the centerline curvature of the S-Duct. In this study, CFD analysis of the RAE M 2129 S-Duct has been performed to investigate the influence of aspect ratio of inlet geometry. The performance of the S-Duct is evaluated in terms of the distortion coefficient. To simulate the flow under adverse pressure gradient better, $k-{\omega}SST$ turbulence model is employed. The computational results are validated with the ARA experimental data. The secondary flow and the flow separation are observed for all computational cases, while the semi-circular geometry has been found to produce the best results.

• Wind and Structures
• /
• v.7 no.5
• /
• pp.317-332
• /
• 2004

Wind tunnel experiments were conducted under highly turbulent and disturbed flow conditions over a solid/perforated plate with a long splitter plate in its plane of symmetry. The effect of varied level of perforation of the normal plate on fluctuating velocities and fluctuating pressures measured across and along the separation bubble was studied. The different perforation levels of the normal plate; that is 0%, 10%, 20%, 30%, 40% and 50% are studied. The Reynolds number based on step height was varied from $4{\times}10^3$ to $1.2{\times}10^4$. The shape and size of the bubble vary with different perforation level of the normal plate that is to say the bubble is reduced both in height and length up to 30% perforation level. For higher perforation of the normal plate, bubble is completely swept out. The peak turbulence value occurs around 0.7 to 0.8 times the reattachment length. The turbulence intensity values are highest for the case of solid normal plate (bleed air is absent) and are lowest for the case of 50% perforation of the normal plate (bleed air is maximum in the present study). From the analysis of data it is observed that $\sqrt{\overline{u^{{\prime}2}}}/(\sqrt{\overline{u^{{\prime}2}}})_{max}$, (the ratio of RMS velocity fluctuation to maximum RMS velocity fluctuation), is uniquely related with dimensionless distance y/Y', (the ratio of distance normal to splitter plate to the distance where RMS velocity fluctuation is half its maximum value) for all the perforated normal plates. It is interesting to note that for 50% perforation of the normal plate, the RMS pressure fluctuation in the flow field gets reduced to around 60% as compared to that for solid normal plate. Analysis of the results show that the ratio [$C^{\prime}_p$ max/$-C_{pb}(1-{\eta})$], where $C^{\prime}_p$ max is the maximum coefficient of fluctuating pressure, $C_{pb}$ is the coefficient of base pressure and ${\eta}$ is the perforation level (ratio of open to total area), for surface RMS pressure fluctuation levels seems to be constant and has value of about 0.22. Similar analysis show that the ratio $[C^{\prime}_p$ max/$-C_{pb}(1-{\eta})]$ for flow field RMS pressure fluctuation levels seems to be constant and has a value of about 0.32.

• Clean Technology
• /
• v.24 no.3
• /
• pp.239-248
• /
• 2018

In this study, pervaporation experiments of water, ethanol and IPA (Isopropyl alcohol) single components and water/ethanol, water/IPA mixtures were carried out using zeolite 4A membranes developed by Fine Tech Co. Ltd. Those membranes were fabricated by hydrothermal synthesis (growth in hydrothermal condition) after uniformly dispersing the zeolite seeds on the tubular alumina supports. They have a pore size of about $4{\AA}$ by ion exchange of $Na^+$ to the LTA structure with Si/Al ratio of 1.0, and shows strong hydrophilic property. Physical characteristics of prepared membranes were evaluated by using SEM (surface morphology), porosimetry (macro- or meso- pore analysis), BET (micropore analysis), and load tester (compressive strength). Pervaporation experiments with various temperature and concentration conditions confirmed that the zeolite 4A membrane can selectively separate water from ethanol and IPA. Water/ethanol separation factor was over 3,000 and water/IPA separation factor was over 1,500 (50 : 50 wt%, initial feed concentration). Pervaporation behaviors of single components and binary mixtures were predicted using ACM (activity coefficient model), GMS (generalized Maxwell Stefan) model and DGM (Dusty Gas Model). The adsorption and diffusion coefficients of the zeolite top layer were obtained by parameter estimation using GA (Genetic Algorithm, stochastic optimization method). All the calculations were carried out using MATLAB 2018a version.

• Management & Information Systems Review
• /
• v.34 no.1
• /
• pp.65-80
• /
• 2015

In previous studies concerning turnover, they argue individual stock's turnover must be identical to market portfolio's turnover under one condition where 2 funds separation theorem holds. In this kind of world, all market participants hold and trade the same portfolio and this should be only market portfolio. If one's trading portfolio's shape is different from market portfolio's, this would mean he or she has an advantage over others in information and this kind of information would be private. In accordance with this theory, we develop a metric which measures how far one's trading portfolio from market's and name it as Stock Selection by Investor(SSI). We apply this measurement to the various types of investor groups classified as individual, institutional and foreign who participate in Korea stock market. To test the validity of measure, we regress price ratio on this measurement using SUR method. As a result, individual investor group shows large number in SSI, but the coefficient in regression is not significant and economically meaningless. In case of institutional investor group, the coefficient proves to be significantly negative. We can infer from this fact that their trading is somehow far from informed trading. Stock selection activity by foreign investor groups proves to be informed trading by showing significantly positive coefficient and the magnitude of coefficient is economically meaningful, especially in sell activity.

• Journal of Korean Society of Transportation
• /
• v.21 no.5
• /
• pp.61-71
• /
• 2003

Existent DDHV draws and is calculating K coefficient. D coefficient from sum of traffic volume two-directions time. There is difference of design order and actuality order, error of DDHV estimation value, problem of irregular change etc. of DDHV thereby. In this study, among traffic volume of each other independent two direction(going up, going down), decide design target order in the directional traffic volume, presented way(way) applying without separating K coefficient and D coefficient at the same time. The result were analysis about national highway permanent count point 360 points 30 orders by existing DDHV estimation value method(separation plan) analysis wave and following variation appear. - design order and actuality order are collision at 357 agencies(99.2%) - actuality order special quality : Measuring efficiency of average 80 orders, maximum 1,027 order, minimum 2 orders - error distribution of design order and actuality order : inside 10 hours is(30$\pm$10hour) 106 points(29.4%), 254 points(70.6%) more than 30 orders and $\pm$10 orders error occurrence be - DDHV estimation value : Average 8.4%, maximum 46.7% The other side, average 50 orders. error improvement effect of DDHV 8.4% was analysed that is at design hourly volume computation by inseparability method in case of AADT premises correct thing because inseparability plan agrees actuality order at whole agency with design order and measuring efficiency of DDHV estimation value is "0".t;0".uot;.

• Journal of the Korea Concrete Institute
• /
• v.17 no.2 s.86
• /
• pp.179-189
• /
• 2005

Corrosion of steel due to chloride attack is a major concern in reinforced concrete structures which are located in the marine environments. In this case, Fick's 2nd law has been used for the prediction of chloride diffusion related with service life of concrete structures. However, those studies were confined mostly to the single deterioration due to chloride only, although actual environment is rather of combined type. The purpose of the present study is, therefore, to explore the influences of carbonation to chloride attack in concrete structures and to investigate the validity of Fick's law to chloride attack combined carbonation. The test results indicate that the chloride ion profiles from Fick's law using the diffusion coefficient of immersion tests is not reflected the effect of separation of chloride ions in carbonation region but valid in sound region in case of combined action. On the other hand, the chloride ion profiles from Fick's law using the diffusion coefficient of Tang and Nilsson's method coincide with test results under dry-wet condition but not under combined condition. The results of present study may Imply that the new method for the measurement of diffusion coefficient is required to predict the chloride ion profiles in case of combined action at early.

• Proceedings of the Ginseng society Conference
• /
• 2002.10a
• /
• pp.491-501
• /
• 2002

A cross-examination between KT&G Central Research Institute and Guangzhou Institute for Drug Control was carried out in order to select optimum conditions for extraction, separation and determination of ginsenosides in red ginseng and to propose a better method for the quantitative analysis of ginsenosides. The optimum extraction conditions of ginsenosides from red ginseng were as follows: the extraction solvent, $70\%$ methanol; the extraction temperature, $100^{\circ}C;$ the extraction time, 1 hour for once; and the repetition of extraction, twice. The optimum separation conditions of ginsenosides on the SepPak $C_{18}$ cartridge were as follows: the loaded amount, 0.4 g of methanol extract; the washing solvents, distilled water of 25 ml at first and then $30\%$ methanol of 25 ml; the elution solvent, $90\%$ methanol of 5 ml. The optimum HPLC conditions for the determination of ginsenosides were as follows: column, Lichrosorb $NH_2(25{\times}0.4cm,$ 5${\mu}m$, Merck Co.); mobile phase, a mixture of acetonitrile/water/isopropanol (80/5/15) and acetonitrile/water/isopropanol (80/20/15) with gradient system; and the detector, ELSD. On the basis of the optimum conditions a method for the quantitative analysis of ginsenosides were proposed and another cross-examination was carried out for the validation of the selected analytical method conditions. The coefficient of variances (CVs) on the contents of ginsenoside-$Rg_{1}$, -Re and $-Rb_1$ were lower than $3\%$ and the recovery rates of ginsenosides were $89.4\~95.7\%,$ which suggests that the above extraction and separation conditions may be reproducible and reasonable. For the selected HPLC/ELSD conditions, the CVs on the detector responses of ginsenoside-Rg, -Re and $-Rb_1$) were also lower than $3\%$, the regression coefficients for the calibration curves of ginsenosides were higher than 0.99 and two adjacent ginsenoside peaks were well separated, which suggests that the above HPLC/ELSD conditions may be good enough for the determination of ginsenosides.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.4
• /
• pp.183-194
• /
• 2021

In this study, the conversion factor for 2020 is estimated based on an outpatient and inpatient conversion factor separation model developed from SGR and AR by using actual medical expense data. In addition, a policy plan is proposed to calculate the values of single and multiple conversion factors for each type of medical expense, and to effectively use the conversion factor separation model as one of the means to establish a medical delivery system. The major results are as follows. First, at r=0.1, the rate of adjustment in the hospital single conversion index in 2020 was 2.0%, and the outpatient and hospitalization conversion rates for hospitals were 2.2% and 2.3%, respectively. In addition, a combination of outpatient and inpatient conversion factors can be used for the adjustment. Second, as a measure to establish a medical delivery system, instead of adjusting the addition rate, a method of interlocking the addition rate and the conversion factor is proposed. Third, it is necessary to develop a model that enables target management of volumes, in addition to the outpatient conversion factor, the inpatient conversion factor, and the adjustment coefficient.

• The Journal of the Convergence on Culture Technology
• /
• v.7 no.4
• /
• pp.85-93
• /
• 2021

The purpose of this study was to investigate the effect of psycological separation, self-control, college satisfaction of smartphone addiction in nursing students. Data were collected from 201 nursing students in B city and analyzed by t-test, ANOVA, Pearson correlation coefficient, and multiple regression using SPSS/WIN 22.0. The degree of smartphone addiction in nursing students was 2.23±.58. There were significant differences in smartphone addiction with respect to alcohol drinking(t=2.530, p=.012), smoking(t=2.302, p=.022), study-time(t=6.036, p=.001), smartphone average daily using time(t=6.036, p=.001). There was negative correlation between smartphone addiction and self-control(r=-.443, p<.001), college satisfaction(r=-.210, p=.033). The factors affecting smartphone addiction of the study subjects were self-control(𝛽=-.355, p<.001), smartphone average daily using time(𝛽=.231, p<.001), smorking(𝛽=-.132, p=.033), with an explanatory power of 27.5%. Through this research requires the fellow study to determine the factors affecting smartphone addiction of nursing students.

• Tribology and Lubricants
• /
• v.36 no.3
• /
• pp.133-138
• /
• 2020

In this paper, we present an experimental investigation of the friction coefficient and wear area change of carbon/epoxy and E-glass/epoxy composites depending on the fiber direction (0°/90°). We compared the results of the case where the sliding direction is parallel to the fiber direction (0°) with that of the case where it is perpendicular to the fiber direction (90°). The ball-on-plate wear test equipment was used to cause wear in both directions. Two types of specimens were prepared with thicknesses of 3 mm-one made of carbon fiber reinforced plastic composite (CFRP) and the other of glass fiber reinforced plastic composite (GFRP). A normal force of 20 N was applied to the specimen and the sliding speed was 10 mm/s and the sliding distance was set to 20 m to perform the wear test. The CFRP demonstrates superior tribological characteristics compared to the GFRP. This outcome is attributed to graphitization of carbon, which serves as solid lubricating particles. In addition, both CFRP and GFRP are worn more in the 90° direction than in the 0° direction. This is due to the greater occurrence of fiber breakage and separation in the 90° direction than in the 0° direction. This study is expected to be utilized as basic data for understanding the friction and wear characteristics of CFRP and GFRP composites along the fiber direction and to apply the appropriate material.