• Journal of Biosystems Engineering
• /
• v.19 no.3
• /
• pp.185-193
• /
• 1994

Both the wet and dry types of garlic peeling machines are being presently used in domestic garlic processing factory, but the dry type is more popular than the wet type because of higher peeling efficiency. The peeling efficiency of these machines is estimated 50 to 80%, depending on the difference in garlic varieties, physical properties and moisture content of garlic samples. If the peeling time is increased in order to improve the peeling efficiency, the damage on the surface of peeled garlic and the consumption of electric power are also increased. This study was carried out to solve these problems in garlic peeling operation and to obtain the optimun design factor for the friction type separator. The results are summarized as follows : 1. The average friction coefficients of peeled and unpeeled garlic samples were 0.91 and 0.51. respectively, for the acrylic plate, and 0.96 and 0.51, respectively, for the stainless plate. 2. For the inclined acrylic pipe with the pipe length 90 cm, the inclined angle $39^{\circ}$ and the pipe diameter 45-55 mm, the falling time of peeled garlic samples was 0.2 sec, faster than unpeeled garlic samples. 3. For the inclined stainless pipe with the pipe length 90 cm, the inclined angle $34^{\circ}$, $39^{\circ}$ and the pipe diameter pipe 35 mm, the falling time of peeled garlic samples was 0.7 sec, slower than that with the pipe diameter 47mm. 4. The stainless pipe with the pipe length 80~90 cm, the inclined angle $39^{\circ}{\sim}40^{\circ}$ and the pipe diameter 40~50 mm was the most suitable as the material of friction pipe. 5. Experimental garlic peeling machine is composed of garlic sample feeding device, friction stainless pipe and hopper. The peeling efficiency was 81 to 96%, and the separating capacity, 600 gr/min.

• The KSFM Journal of Fluid Machinery
• /
• v.19 no.4
• /
• pp.48-53
• /
• 2016

The centrifugal separator which uses gravity separation method for oil-water separation, rotating at high-speed, is one of the most commonly used device for controlling the amount of the oil in waste water collected in bilge. The IMO (International Maritime Organization) has set regulations, also known as MARPOL 73/78, for the prevention of marine pollution. In addition, DET NORSKE VERITAS (DNV) has set standards regarding the assignment of Environmental Class Notation, CLEAN or CLEAN DESIGN, of ships. One of the requirements for classification is that in addition to conforming to MARPOL 73/78, more stringent measures must be taken as well. One of these measures is to limit the oil concentration in bilge water to less than 5ppm. So in this study, an Oil-Water Separator (OWS) is used together with multiple separating plates as a filtration system to be used as an oil-water separation device. The OWS operates using centrifugal separation in which the mixture is separated by centrifugal forces. The main purpose of this paper is to present the OWS separation efficiency according to the rotation speed, mass-flow rate, the angle and the number of stacked layers of the laminated plate using Computational Fluid Dynamics (CFD). Improvements to the device will be investigated from these results.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.53 no.6
• /
• pp.145-152
• /
• 2011

In order to heat greenhouse nearby river channel, riverbank filtration water source heat pump was developed for getting plenty of heat flux from geothermal energy. Recharging well, thermal storage tank with separating insulation plate and filtering tank for eliminating iron, manganese were mainly developed for making the coefficient of performance (COP) of heat pump higher. Heating system using riverbank filtration water source heat pump was installed at a paprika greenhouse in the Jinju region where a single fold of vinyl cover and 2 layers of horizontal thermal curtain were installed as a part of temperature keeping and heat insulation with a greenhouse area of 3,185 $m^2$. 320,000 kcal/h was supplied for performing a site application tests. A greenhouse heating test was performed from Feb. 1, 2011 to Apr. 30, 2011. As the result of that, COPh of the heat pump was measured in the range of 4.0~4.5, while COPS of the system was represented as 2.9~3.3. COP measured of the heat pump was very good and well responded to indoor heating temperature of the environment control system of a greenhouse.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.20-23
• /
• 2001

Plasma Display Panel(PDP) is a type of flat panel display utilizing the light emission produced by gas discharge. Barrier Ribs of PDP separating each sub-pixel prevents optical and electrical crosstalks from adjacent sub-pixels. The mold for forming the barrier ribs has been newly researched to overcome the disadvantages of conventional manufacturing processes such as screen printing, sand-blasting and photosensitive glass methods. The mold for PDP barrier ribs have stripes of micro grooves transferring glass-material wall. In this paper, Stripes of grooves of which width 48${\mu}{\textrm}{m}$, depth 124$\mu\textrm{m}$ , pitch 274$\mu\textrm{m}$ was acquired by machining of single crystal silicon with dicing saw blade. Maximum roughness of the bottom of the grooves was 59.6nm Ra in grooving Si. Barrier ribs were formed with silicone rubber mold, which is transferred from grooved Si forming hard mold. Silicone rubber mold has the elasticity, which enable to accommodate the waveness of lower glass plate of PDP. The methods assisted by the microwave and UV was adopted for reducing the forming time of glass paste.

• Journal of Biosystems Engineering
• /
• v.42 no.1
• /
• pp.12-22
• /
• 2017

Purpose: This aim of this study was to develop a pick-up type pulse crop harvester for harvesting cut and dried pulse crop. Methods: The pick-up type pulse crop harvester was designed and constructed. Its specifications and operating performance were investigated. Results: Compared with conventional bean harvesters, the pick-up type pulse crop harvester adopted seven rows of chains with tines to pick-up the cut and dried pulse crop on a flat or ridged field, two transverse threshing drums with steel wire teeth to reduce the threshing speed, and a tilt plate and plastic bucket elevator for conveying clean grain to reduce damage. The threshing speed and the oscillating frequency of the separating and cleaning parts according to crop type and condition could be varied easily to efficiently use engine power and to improve harvesting performance. The harvester showed forward speed ranges of 0 ~ 1.5 m/s during harvesting operation, and 0 ~ 2.5 m/s during road travelling. The pick-up width of the harvester was about 1 m. Conclusions: The pick-up type self-propelled 51.5 kW harvester was designed and constructed to harvest cut and dried pulse crop. The effective field capacity of the harvester was predicted as above 40 a/h.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.6
• /
• pp.498-503
• /
• 2012

Independent component analysis (ICA) technique based on statistical independency of the signals is known as suitable to identify the source signals by measuring and separating mixed signals through transfer paths and has successfully applied in the field of medical care, communications and so forth. In this study, the ICA technique is introduced for the identification of excitation sources from measured vibration signals of structures, which can be done by evaluating negentropy of centered and whitened vibration signals and correlation of separated signals. To validate the method, numerical analyses are carried out for a plate and a cylinder structure. The results show that the method can be applied efficiently to source identification of complex structures. Nevertheless, additional studies would be required to complement problems of occasional inaccuracy.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2003.07a
• /
• pp.61-64
• /
• 2003

Optical resolution of a-amino acid (tryptophan and tyrosine) optical isomers was achieved by a pressure driven membrane separation process, using self-supporting crosslinked membranes base on polysaccharide with different swelling indices that ranged from 100 to 70%. The membranes prepared by casting and drying the polymer solution containing 5wt% acetic acid on an acryl plate followed by crosslinking with glutaraldehyde were characterized using such analytical methods as FTIR and swelling index measurements. On the way of separating the optical isomers, several experimental factors such as the concentration of the feed solutions, operating pressure and temperature, and degree of crosslinking of the membranes have been studied. When the chitosan membranes with 70% of swelling index were used , almost complete optical resolution was obtained; 97.92% of enantiomeric excess (ee %) and 2.26 g/$m^2$ㆍh of flux. The operating pressure and the concentration of feed solutions were respectively 1.0 kgf/$\textrm{cm}^2$ and 0.49 mmol/L.

• Journal of Environmental Science International
• /
• v.20 no.1
• /
• pp.137-146
• /
• 2011

In this research, food waste source reduction model for apartment was investigated. In spite of prohibition of direct landfill of food waste and continuous efforts made by government and local government, food waste production increases steadily. Recycling ratio of the food waste increases every year, but its products have many problems like low quality, stability, salt, odor etc. Household occupies 63.3% of whole food waste production and this is subject to be a key factor to control food waste. We surveyed S apartment in Kwangju city as a model case, in which administrative office and women's association adopted clean plate eating, separation of raw food waste and earth worm composting as a series of method for source reduction and recycling inside the apartment. With the help of residents' participation and practice, food waste production decreased 15.6% from 0.31 g/capita/day in 2007 to 0.26 g/capita/day in 2009 (domestic average 0.30 g/capita/day). Separation of raw food waste and its composting using earth worm were very effective, and were subject to resolve the problems of present food waste treatment technologies. And earth worm composting was very useful in environmental, economical, societal and educational aspects. Instead of economical incentive, educational programs about food value, environmental problem and critical method for food waste separation were more effective for promotion of source reduction. From the analyses on the process and success factors in this model, we could conclude that leader's role was one of the key factors for the settlement of source reduction, and that was to understand the seriousness of the food waste and to seek solution, to test techniques, and to practice by oneself. Furthermore, networking and collaboration among residents, local government, NGO and local press promoted residents' participation, and it was through various education and investigation. Finally, source reduction and self recycling model of food waste in the apartment, that applies separating raw food waste and earth worm composting based on the collaboration among residents, local government, NGO, and local press, should be disseminated, and environmental policy also should be changed to make it possible.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.172.2-172.2
• /
• 2010

This study was carried out in order to reduce the installation expense of heating system for greenhouse comparing to geothermal heat pump and develope the coefficient of performance (COP) for a heat pump. For getting plenty of heat flux from geothermal energy. Surface water in river channel was used for getting a lots of geothermal heat by penetrating water through underground soil layer of the river bank that make heat transmission to passing water. The range of water temperature after the process of Ground filtration is 13~18 degrees celsius which is very similar to low heat source of geothermal heat pump system and the plenty amount of heat source from that make the number of geothermal heat exchanging hole and the expense for geothermal heat exchanger construction reduced. Drainage well is also used for returning filtration water to the aquifer that keep the water good recirculation from losing geothermal heat and water resource. For the COP improvement of Heat pump, thermal storage tank with separating insulation plate according to the temperature difference make the COP of Heat pump that is similar to thermal storage tank with diffuser. Developed thermal storage tank make construction expense cheaper than customarily used one's. and that sand filter and oxidation sand (FELOX) are going to be used for improving ground filtration water quality that make heat exchanger efficiency better. All above developed component skill are going to be set on the Ground filtration water source heat pump system and applied for medium, large scale for protected greenhouse in riverside area and on-site experiment is going to do for optimizing the heating system function and overcome the problem happening in the process of on-site application afterward.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.6
• /
• pp.176-183
• /
• 2002

Plasma Display Panel(PDP) is a type of flat panel display utilizing the light emission produced by gas discharge. Barrier Ribs of PDP separating each sub-pixel prevents optical and electrical crosstalks from adjacent sub-pixels. The mold for forming the barrier ribs has been newly researched to overcome the disadvantages of conventional manufacturing processes such as screen printing, sand-blasting and photosensitive glass methods. The mold for PDP barrier ribs have stripes of micro grooves transferring glass-material wall. In this paper , Stripes of grooves of which width 48$\mu$m, depth 124$\mu$m , pitch 274$\mu$m was acquired by machining of single crystal silicon with dicing saw blade. Maximum roughness of the bottom of the grooves was 59.6 nm Ra in grooving Si. Barrier ribs were farmed with silicone rubber mold, which is transferred from grooved Si forming hard mold. Silicone rubber mold has the elasticity, which enable to accommodate the waviness of lower glass plate of PDP. The methods assisted by the microwave and UV was adopted for reducing the forming time of glass paste.