• Journal of KIEE
• /
• v.11 no.1
• /
• pp.1-7
• /
• 2001

Various methods for blind source separation (BSS) are based on independent component analysis (ICA) which can be viewed as a nonlinear extension of principal component analysis (PCA). Most existing ICA methods require certain nonlinear functions (which leads to higher-order statistics) depending on the probability distributions of sources, whereas PCA is a linear learning method based on second-order statistics. In this paper we show that the PCA can be applied to the task of BBS, provided that source are spatially uncorrelated but temporally correlated. Since the resulting method is based on only second-order statistics, it avoids the nonlinear function and is able to separate mixtures of several colored Gaussian sources, in contrast to the conventional ICA methods.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.10
• /
• pp.955-956
• /
• 2000

Solvolyses of methanesulfonyl chloride in water, $D^2O$, $CH^3OD$, and in aqueous binary mixtures of acetone, eth-anol and methanol are investigated at 25, 35 and $45^{\circ}C.$ The Grunwald-Winstein plot of first-order rate con-stants for the solvolytic react ion of methanesulfonyl chloride with YCl (based on 2-adamantyl chloride) shows marked dispersions into three separate lines for three aqueous mixtures with a small m value (m < 0.30), and shows a rate maximum for aqueous alcoholic solvents. Stoichiometric third-order rate constants, kww and kaa were calculated from the observed first-order rate constants and (kaw + kwa) was calculated from the kww and kaa values. The kinetic solvent isotope effects determined in water and methanol are consistent with the proposed mechanism of the general base catalyzed and/or SAN/SN2 reaction mechanism for methanesulfonyl chloride solvolyses based on mass law and stoichiometric solvation effect studies.

• Annual Conference of KIPS
• /
• 2013.05a
• /
• pp.45-48
• /
• 2013

In this paper, we proposed an Indexing Structure System (ISS) based on Apache Hadoop in Wireless Sensor Network (WSN). Nowadays sensors data continuously keep growing that need to control. Data constantly update in order to provide the newest information to users. While data keep growing, data retrieving and storing are face some challenges. So by using the ISS, we can maximize processing quality and minimize data retrieving time. In order to design ISS, Indexing Types have to be defined depend on each sensor type. After identifying, each sensor goes through the Indexing Structure Processing (ISP) in order to be indexed. After ISP, indexed data are streaming and storing in Hadoop Distributed File System (HDFS) across a number of separate machines. Indexed data are split and run by MapReduce tasks. Data are sorted and grouped depend on sensor data object categories. Thus, while users send the requests, all the queries will be filter from sensor data object and managing the task by MapReduce processing framework.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.34 no.2
• /
• pp.185-194
• /
• 2016

The purpose of this study is to present a method to provide environment information based on spatial information document. At present, a lot of spatial information, including environment information, is being produced, but separate software or system is required for the user to acquire the information. In particular, in the case of environment information, various types of information are being produced, such as ecology, vegetation and measurement network data. Therefore, it is necessary to present the form and the making method of spatial information document that allows using environment information as spatial information without separate software or system. To provide spatial information document-based environment information, types and forms of environment information, data format and offering methods produced by the government, in particular, the Ministry of Environment and the local governments, are analyzed. 12 fields are classified and the form of produced data is GIS DB, measurement network data, text data and so on. With decrease of paper maps, spatial information document that offers display by layer, coordinate data, attribute data, distance and area measurement, location search by coordinates, GPS location linkage and location display on the map is presented to increase utilization of geo-environment information maps. Finally, the standard document specification based on spatial information document is presented in consideration of usability and readability in order to provide a variety of environment information without separate software or system.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.4
• /
• pp.48-56
• /
• 2012

The object of this paper is the controller for supplying stably power in a separate house in which a hybrid electrical storage system with a stand-alone photovoltaic/wind power generation system and a small generator is applied. In the photovoltaic/wind hybrid power system used in the separate house, when only the battery is used in sunless days, the capacity of the battery is become larger. In particular, as in recent days, if cloudy days are frequent due to anomaly climate, it is difficult to estimate the number of sunless days. Accordingly, it is preferable to build the electrical storage system that numbers of sunshineless days are to be controlled and a shortage amount of the power generation capacity is to be handled by a small generator system. In order to supply stably power of new renewable energy such as solar to any separate houses, it is preferable to reduce the capacity of battery by decreasing the number of sunless days when estimating the capacity of battery and to drive the small generator for compensation of the power shortage. Such system needs components including inverters for photovoltaic and wind power generation system, batteries and controllers for automatically driving the small generator, based upon the nature of the stand-alone house, and it is preferable to use the controller having a simpler and higher stability by adopting the all-in-one scheme to facilitate its maintenance.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.3B
• /
• pp.152-158
• /
• 2008

Recently, DDoS (Distributed Denial of Service) attack has emerged as one of the major threats and it's main characteristic is to send flood of data packets toward a specific victim. Thus, several attack detection schemes which monitor the destination IP address of packets have been suggested. The existing Bloom Filter based attack detection scheme is simple and can support real-time monitoring. However, since this scheme monitors the separate fields of destination IP address independently, wrong detection is comparatively high. In this paper, in order to solve this drawback, an efficient Bloom Filter based destination address monitoring scheme is proposed, which monitors not only separate fields but also relationship among separate fields. In the results of simulation, the proposed monitoring scheme outperforms the existing Bloom Filter based detection scheme. Also, to improve the correctness of detection, multi-layerd structure is proposed and the correctness of result is improved according to the number of layers and extra tables.

• Journal of Aerospace System Engineering
• /
• v.13 no.1
• /
• pp.38-46
• /
• 2019

There is a growing interest in engine diagnostic technology for gas turbine engines. An engine simulation program, precisely simulating the engine performance, is required in order to apply it to the engine diagnosis technology for engine health monitoring. In particular, the simulation program can predict not only design point performance but also off-design point and partial load performance in accurate. So the engine simulation program for the 2-spool separate flow type turbofan engine was developed and the JT9D-7R4G engine of PW(Pratt & Whitney) was analyzed. The steady-sate performance analysis is conducted at both design and off-design points in flight path and the differences between analysis results of takeoff and cruise conditions are compared. The effect of Reynold's correction method was analyzed as a scaling method of the engine component performance. The simulation results was compared with NPSS.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.636-640
• /
• 2000

A novel integrated battery charger/discharger converter for a standardized battery module is proposed. Instead of using separate charger and discharger converters. it integrates these two converters into a single converter in order to minimize the size. the integrated charger/discharger converter not only regulates the solar array output power including the peak power tracking capability but also controls the battery charging/discharging current depending on the solar array output power and the load power. In addition it offers a regulated bus voltage which simplifies the power distribution/conversion for the pay load.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.32 no.11
• /
• pp.404-416
• /
• 1983

This paper is concerned with the design automation of the sequential machines. The operations of sequential machine can be diveded into two types such as synchronous and asynchronous sequential machine and their realization is treated in separate mode. But, in order to integrate logic circuits in high volume, mixed mode sequential machine uses common circuitry that consists of gates and flip-flops. Proposed sequential machine can be designed by several method, which are hard-wired implementation, firmware realization by PLA and ROM. And then onr example shows the differnces among three design mothods. Finally, computer algorithm(called MINIPLA) is discussed for various application of mixed-mode sequential machine.

• Journal of Institute of Convergence Technology
• /
• v.10 no.1
• /
• pp.13-17
• /
• 2020

Among the factors that must be taken into account when using thermal imaging cameras that are expanding their application to various fields, a basic study was conducted focusing on temperature on the effect of solar radiation on the photographed thermal image. Through all experiments, in order to use an image taken with a thermal imaging camera for an object installed or located outdoors, a separate temperature correction according to the size of solar radiation or a separate device to block the effect of solar radiation must be additionally installed. Since the temperature of the same object may vary in the thermal image taken indoors or outdoors, it is necessary to calibrate it through comparison with other temperatures as a reference point. In the case of measuring the temperature of a glossy surface such as metal indoors with a thermal imaging camera, it was confirmed that an environment that can remove the light reflection effect by the glossy surface must be constructed and photographed.