• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.10-12
• /
• 2007

본 논문에서는 BLDC센서리스를 위해 역기전력의 영점검출을 위한 새로운 필터회로를 설계하였다. 특히 본 논문에서 제안한 역기전력 증폭 제한회로를 구성함에 있어 아날로그 디지털 혼용 필터회로를 구성하여 저속영역에서 센서리스를 특성을 개선하였다. 또한 100[W]급 BLDC 구동용 프로토 타입 드라이브를 제작하여 제안된 알고리즘의 타당성 검증하였다.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.220-223
• /
• 2005

In this paper, a novel sensorless brushless DC (BLDC) motor drive method using the fuzzy back-EMF observer is proposed to improve the performance of conventional sensorless drive methods. Most existing back-EMF sensing methods need additional circuit and have a low performance intransient state or low speed range. Therefore, this paper proposes the fuzzy back-EMF observer and an algorithm using this observer to estimate a speed and a position of the rotor. The robustness of the proposed algorithm is proved through the simulation compared with other sensorless drive methods.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.1
• /
• pp.48-56
• /
• 2006

This paper studies particularly applicable method for sensorless PM BLDC motor drive system. The waveform of the motor internal voltages(or back emf) contains a fundamental and higher order frequency harmonics. Therefore the third harmonic component is extracted from the stator phase voltage. The resulting third harmonic signal keeps a constant phase relationship with the rotor flux for any motor speed and load condition. Also because of low resolution of estimated signal obtained by the proposed sensorless algorithm, to improve the wide range of speed response characteristic more exactly, we propose the rotor position signal synthesizer using PLL circuit based on estimated signals. Some experimental results are provided to demonstrate the validity of the proposed control method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.4
• /
• pp.323-330
• /
• 2005

In order to increase reliability and reduce system cost, this paper studies particularly applicable method for sensorless PM BLDCM drive system. The waveform of the motor internal voltages(or back emf) contains a fundamental and higher order frequency harmonics. Therefore the third harmonic component is extracted from the stator phase voltage. The resulting third harmonic signal keeps a constant phase relationship with the rotor flux for any motor speed and load condition, and is practically free of noise that can be introduced by the inverter switching, making this a robust sensing method. In addition, a simple starting method and a speed estimation approach are also proposed. Some experimental results are Provided to demonstrate the validity of the proposed control method.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.4
• /
• pp.1540-1551
• /
• 2015

The detection of position and speed in BLDC motors without using position sensors has meant many efforts for the last decades. The aim of this paper is to develop a sensorless technique for detecting the position and speed of BLDC motors, and to overcome the drawbacks of position sensor-based methods by improving the performance of traditional approaches oriented to motor phase voltage sensing. The position and speed information is obtained by computing the derivative of the terminal phase voltages regarding to a virtual neutral point. For starting-up the motor and implementing the algorithms of the detection technique, a FPGA board with a real-time processor is used. Also, a versatile hardware has been developed for driving BLDC motors through pulse width modulation (PWM) signals. Delta and wye winding motors have been considered for evaluating the performance of the designed hardware and software, and tests with and without load are performed. Experimental results for validating the detection technique were attained in the range 5-1500 rpm and 5-150 rpm under no-load and full-load conditions, respectively. Specifically, speed and position square errors lower than 3 rpm and between 10º-30º were obtained without load. In addition, the speed and position errors after full-load tests were around 1 rpm and between 10º-15º, respectively. These results provide the evidence that the developed technique allows to detect the position and speed of BLDC motors with low accuracy errors at starting-up and over a wide speed range, and reduce the influence of noise in position sensing, which suggest that it can be satisfactorily used as a reliable alternative to position sensors in precision applications.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.5
• /
• pp.407-412
• /
• 2015

This paper presents the design of a lab-built powered knee prosthesis based on a BLDC motor, a sensored impedance control using a force sensor, and a sensorless impedance control through torque estimation. Firstly, we describe the structure of the lab-built powered knee prosthesis and its limitations. Secondly, we decompose the gait cycle into five stages and apply the position-based impedance control for the powered knee prosthesis. Thirdly, we perform an experiment for the torque estimation and the sensorless impedance control of the prosthesis. The experimental results show that we can use the torque estimation to control the low impedance during the swing phase, although the estimated torque data has a delay compared with the measured torque by a load cell.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.4B no.3
• /
• pp.108-113
• /
• 2004

This paper presents methods to improve performance of the power supply system in a NASA deep space explorer. In the Stirling engine driven reciprocating Brushless DC (BLDC) generator, the accurate position information of the prime mover is important to diagnose the performance of the engine and prevent distortion of the output power. Since sensors to detect the position are fragile and unreliable, and conventional sensorless techniques have drawbacks in the low speed region, a novel sensorless position detection technique for the prime mover has been proposed and verified. Another major issue of the generator for the spacecraft is power density maximization. The mass of the power system is important to the mass of the satellite. Therefore, the components of the spacecraft should be lightweight. Conventional rectification methods cannot achieve the maximum power possible due to non-optimal current waveforms. The optimal current waveform for maximizing power density and minimizing machine size and weight in a nonsinusoidal power supply system has been derived, incorporated in a control system, and verified by simulation work.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.3 no.1
• /
• pp.1-6
• /
• 2014

A new sensorless control strategy for brushless DC (BLDC) motors is proposed in this paper. This technique builds a rotor position-related flux function, which is independent of the speed. By observing the flux function, the information of rotor position and commutation can be obtained. As the function is not speed-related, this control process can be used in a wider range of speed and improves the motor's performance during startup. An experimental test bad based on TMS320F2812 has been built, and the experimental result indicates that the motor achieves a smooth starting-up and stable phase commutation with the proposed control strategy.

• International Journal of Control, Automation, and Systems
• /
• v.6 no.4
• /
• pp.477-487
• /
• 2008

This paper proposes a new position sensorless drive for brushless DC (BLDC) motors. Typical sensorless control methods such as the scheme with the back-EMF detection method show high performance only at a high speed range because the magnitude of the back-EMF is dependent upon the rotor speed. This paper presents a new solution that estimates the rotor position by using an unknown input observer over a full speed range. In the proposed method, a trapezoidal back-EMF is modelled as an unknown input and the proposed unknown input observer estimating a line-to-line back-EMF in real time makes it possible to detect the rotor position. In particular, this observer has high performance at a low speed range in that the information of a rotor position is calculated independently of the rotor speed without an additional circuit or complicated operation process. Simulations and experiments have been carried out for the verification of the proposed control scheme.

• Journal of Power Electronics
• /
• v.19 no.5
• /
• pp.1203-1215
• /
• 2019

Sensorless brushless DC (BLDC) motor drive systems are often subjected to inaccurate commutation signals and can produce high current peaks and conduction consumption. To achieve accurate commutation, a fast commutation shift regulation method for sensorless BLDC motor drive systems considering the influence of the inductance freewheeling process is presented to compensate inaccurate commutation signals. The regulation method is effective in both steady speed and variable speed operations. In the proposed method, the commutation error is gained from the line-voltage difference integral in a 60 electrical-degree conduction period and the outgoing phase current before commutation. In addition, the detection precision of the commutation error is improved due to the consideration of the freewheeling period. The commutation error is directly obtained, which avoids successive optimization and accelerates the convergence rate of the proposed method. Moreover, the commutation error features a positive or negative sign, which can be utilized as an indicator of advanced or delayed commutation. Finally, experiments are conducted to validate the effectiveness and feasibility of the proposed method. The results obtained show that the proposed method can accurately regulate commutation signals.