• The Journal of the Korea institute of electronic communication sciences
• /
• v.3 no.4
• /
• pp.266-275
• /
• 2008

The sensorless speed control technique for BLDC motor using digital IP control is proposed in this paper for advanced speed characteristic which is robust to motor parameters and load variations. The sensorless drive of BLDC motor using terminal voltages is affected by load or speed because it uses analog filters to estimate the rotor position. For this reason, the robust speed controller with the accurate rotor position estimator is needed for sensorless control which is robust to load and insensitive to motor parameters. The constant speed robust to load variation and the stable sensorless control of BLDC motor robust to the increase or decrease of speed with constant load is implemented using digital IP control in this paper. The validity to these is established with experimentation.

• Journal of Industrial Technology
• /
• v.35
• /
• pp.9-13
• /
• 2015

In this paper, a new excitation scheme is developed to increase the output torque of the sensorless BLDC(Brushless DC) motor(BLDCM), which drives fins to control the flight attitude of a guided artillery munition. The proposed scheme is based on a 12-step excitation strategy combining two-phase and three-phase excitations. The proposed 12-step excitation scheme can produce more torque than a typical 6-step scheme for the start-up and synchronous operation in the sensorless BLDCM drive. The simulation and experimental results on the sensorless BLDCM drive system to control the fin were verified the validity of the proposed scheme.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.9
• /
• pp.1-7
• /
• 2014

Brushless Direct Current(BLDC) Motor is essential to measure a rotor position because of that this motor type needs to synchronize the rotor's position and changeover phase current instead of a brush and commutator used on the existing dc motor. Recently, many researches have studied on sensorless control drive for BLDC motor. The conventional control methods are a compensation value dq, Kalman filter, Fuzzy logic, Neurons neural network, and the like. These methods has difficulties of detecting BEMF accurately at low speed because of low BEMF voltage and switching noise. And also, the operation is long and complex. So, it is required a high-performance microprocessor. Therefore, it is not suitable for a small BLDC motor sensorless drive. This paper presents control methods suitable for economic small BLDC motor sensorless drive which are an improved design of the BEMF detection circuit, simplifying a complex algorithm and computation time reduction. The improved motor sensorless drive is verified stability and validity through being designed, manufactured and analyzed.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.79-83
• /
• 1997

The inverter fed BLDC(Brushless DC) motor has been increasingly applied to industry and home appliances due to the advance of power electronics and permanent magnet technology, and its high efficiency and good acoustic noise characteristics. The BLDC motor and drives, however, require the rotor position sensors that may cause some problems such as the high cost and space. In this paper, sensorless algorithm for an interior permanent magnet BLDC motor is proposed. The maximum torque per ampere operation with advance angle considering load torque and speed was simulated and verified through the experiment.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1144-1145
• /
• 2007

This paper is investigated the sensorless drive for BLDC motor using microprocessor. Since the BLDC motor should be commutated according to a rotor position, the sensors are required to detect the position. But the sensors increase cost and volume, complicate the motor configuration, and do not operate properly in some operating environments such as high temperature conditions, so that the necessity of sensorless commutation algorithm is getting increased. This paper is proposed the method to drive BLDC motor without position-detecting sensor using Back EMF. Back EMF commutation method was implemented the sensorless drive system which could control the rotational speed and monitor the behavior of a motor.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.1
• /
• pp.63-69
• /
• 2008

The position of stator is essential when a trapezoidal BLDC motor is drived. In this paper we proposed a novel sensorless drive system for the trapezoidal BLDC motor without hall sensors or encoders. The resistor Y-connecting method is used to obtain Back-emf of a trapezoidal BLDC motor. Especially, by using the new Back-emf filter circuit proposed in this paper the sensorless characteristic in low speed is improved. The prototype proposed system applied for a 100[W] rating BLDC motor is made and the propriety of the Back-EMF filter circuit is also verified.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.1
• /
• pp.95-102
• /
• 2014

This paper presents zero crossing point(ZCP) estimation methods considering discretization error for a high speed brushless DC(BLDC) motor drive. The ZCP is estimated by detecting the change of back-EMF polarity for the BLDC sensorless drive, and the discretization error exist on the estimated ZCP. The discretization error of the ZCP is a cause of the delay of a commutation timing of current and increment of a current ripple factor. Besides a delay of a ZCP estimation brings on the limitation of a speed range for the BLDC sensorless drive. The compensation method based on the error analysis with probability theory for reducing the effects of the discretization error of the ZCP is proposed. Also a ZCP estimation method according to the Back-EMF patterns is proposed to widen the speed range for the BLDC sensorless drive. The proposed methods are verified by the experiment.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.5
• /
• pp.440-446
• /
• 2006

The magnitude of output torque in a BLDC Motor depends on torque angle so that the exact initial position of rotor is essentially required for good starting. This paper presents a novel starting control method for smooth starting in a position-sensorless controlled BLDC motor drive for reciprocating compressor of refrigerator. The proposed method starts a BLDC motor using information on the initial position of rotor, determined from current response characteristics, and shows robust starting capability to starting load variations. The effectiveness of the proposed method is verified through experimental results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.1
• /
• pp.65-71
• /
• 2006

In this paper, a novel motor control method is proposed to improve the performance of sensorless drive of BLDC motors. In the terminal voltage sensing method, which is a great portion of sensorless control, a precise rotor position cannot be obtained when excessive input is applied to the drive during synchronous operation mode. Especially in the transient state, the response characteristic decreases. To cope with this problem, the unknown input (back-EMF) is modelled as the additional state of system in this paper. Taking into account the disturbance adopted by the back-EMF, the observer can be obtained by the augmented system equation. An algorithm to detect the back-EMF of the BLDC motor using the state observer is constructed. As a result, the novel sensorless drive of BLDC motors that can strictly estimate rotor position and speed is proposed.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.4
• /
• pp.342-348
• /
• 2014

In this paper, a BLDC(Brushless DC) motor control system for driving fins to control the flight attitude of the guided artillery munition is developed. This system adopts a sensorless control scheme without any position sensor such as a Hall sensor fragile at high altitudes. The sensorless control of the BLDC motor is achieved by using commutation signals obtained from the measured pole voltages. The position control of the fin is also performed by using of the estimated speed from the commutation signals. The experimental results on the actual fin drive system demonstrated that the developed sensorless control algorithm can give an excellent position control performance.