• Bulletin of the Korean Chemical Society
• /
• v.30 no.7
• /
• pp.1470-1474
• /
• 2009

Thermal and photochemistry of methyl iodide ($CH_3I)\;adsorbed\;on\;D_2O$ ice film on Cu(111) at 100 K were studied using temperature-programmed desorption (TPD) time-of-flight mass spectrometry (TOF-MS), X-ray and ultraviolet photoelectron spectroscopies. On the basis of TPD, multilayer and monolayer $CH_3I$ molecules desorb from $D_2O$ ice layer at 120 and 130 K, respectively. Photo-irradiation at 100 K exhibits dramatic changes in the TPD and I $3d_{5/2}\;XPS\;of\;CH_3I$ on ice film, due to a dramatic dissociation of $CH_3I$. The dissociation is likely activated by solvated electrons transferred from the metal substrate during photo-irradiation. No other photo-initiated reaction products were found within our instrumental detection limit. During photo-irradiation, the $CH_3I$, $CH_3$ and I could be trapped (or solvated) in ice film by rearrangement (and self-diffusion) of water molecules. A newly appeared parent molecular desorption peak at 145 K is attributed to trapped $CH_3I$. In addition, the $CH_3$ and I may diffuse through ice and chemisorb on Cu(111), indicated by TPD and I $d_{5/2}$ XPS taken with photo-irradiation time, respectively. No molecular ejection was found during photo-irradiation at 100 K. The work functions for $CH_3I/Cu(111),\;D_2O/Cu(111)\;and\;CH_3I/D_2$O/Cu(111) were all measured to be about 3.9 eV, 1.0 eV downward shift from that of clean Cu(111).

• Journal of the Korean Geotechnical Society
• /
• v.27 no.1
• /
• pp.35-40
• /
• 2011

Dredging and disposal is a conventional method to remove contaminated sediments. However, there are some problems in dredging and disposal, such as disturbance of contaminated sediments, disposal site determination, and high construction cost. Recently, in-situ capping which overcomes the problems of dredging and disposal is widely applied to isolate local contaminated sites. Numerical studies, which have been conducted to simulate contaminant transport during in-situ capping, have been concerned mainly with diffusive transport. However, contaminated sediments experience large strain consolidation induced by self-weight because of initially high moisture content of sediments, and contaminant transport results from advection and diffusion. Previous studies focus on contaminant transport during consolidation, but have neglected consolidation effect on long-term contaminant transport in sediments. This study presents numerical simulation results of consolidation effect on long-term contaminant transport in sediments.

• Journal of the Korea Institute of Building Construction
• /
• v.22 no.5
• /
• pp.425-430
• /
• 2022

Concrete used for the foundation of high-rise buildings is often placed through in an integrated pouring to ensure construction efficiency and quality. However, if concrete is placed integrally, there is a high risk of temperature cracking during the hydration reaction, and it is necessary to determine the optimal mixing design of high-performance, high-durable concrete through the replacement of the admixture. In this study, experiments on salt damage, carbonation, and sulfate were conducted on the specimen manufactured from the optimal high-performance low-heating concrete combination determined in the author's previous study. The resistance of the cement matrix to chlorine ion diffusion coefficient, carbonation coefficient, and sulfate was quantitatively evaluated. In the terms of compression strength, it was measured as 141% compared to the structural design standard of KCI at 91 days. Excellent durability was expressed in carbonation and chlorine ion diffusivity performance evaluation. In particular, the chlorine ion diffusion coefficient, which should be considered the most strictly in the marine environment, was measured at a value of 4.09×E-12m²/y(1.2898×E-10m²/s), and is expected to be used as a material property value in salt damage durability analysis. These results confirmed that the latent hydroponics were due to mixing of the admixture and high resistance was due to the pozzolane reaction.

• Journal of the Korean Vacuum Society
• /
• v.18 no.2
• /
• pp.127-132
• /
• 2009

We have investigated the intrinsic defects remaining in epitaxial GaSb layers grown on SI-GaAs substrates compared to those in bulk GaSb crystal substrate, which is a basic material of Sb-based strained-layer superlattice infrared photodetectors. From the functional dependence of the band-to-band transition energy of the photomuminescence (PL) spectra observing up to near room-temperature (250 K), the temperature parameters of [$E_o$, $\alpha$, $\beta$] of undoped GaSb crystal are determined by using the Varshni empirical equation describing the temperature variation of the bandgap energy. Additionally to the antisite-Ga ([$Ga_{Sb}$]) with an ionization energy of 29 meV that is well known to a major intrinsic defect in GaSb, epitaxial GaSb layers show a pair of deep states at the emission energy of 732/711 meV that may be related with a complex of two antisite-Ga and antisite-Sb ([$Ga_{Sb}-Sb_{Ga}$]). Based on the analysis of the temperature and the excitation-power dependences of PL, it suggests that excess-Sb substitutes Ga-site by self-diffusion and two anti sites of [$Ga_{Sb}$] and [$Sb_{Ga}$] could form as a complex of [$Ga_{Sb}-Sb_{Ga}$] in GaSb epilayers grown under Sb-rich condition.

• Agribusiness and Information Management
• /
• v.3 no.2
• /
• pp.43-62
• /
• 2011

The goal of this study is to determine, based on survey results, the underlying factors that affect the intention of the farmers who have not adopted the Hazard Analysis and Critical Control Points (HACCP) system for the rearing phase of pig production to adopt this system in the future. The research model for this study was con structed based on strategic contingency theory, the theory of the diffusion of innovation, and the technology acceptance model (TAM). Using structural equation modeling with partial least squares (PLS), this study analyzes the effects of the intensity of competition, the environmental uncertainty, the innovativeness and self-efficacy of the individual farmers, and the impact of the credibility of the Agricultural Technology Service Center (ATSC), which acts as the principal agent of technology dissemination and as a leader of change, on the perceived usefulness of technology and the farmers' intention to adopt the system. The results of the analysis are as follows. First, with regard to the underlying factors affecting the intention to adopt the new system, the intensity of competition within the industry and the institutional credibility of the ATSC were inferred to underlie the perceived usefulness. Second, institutional credibility has a positive impact on the perceived usefulness of the system, and the perceived usefulness, in turn, has a positive impact on the intention to adopt. The perceived ease of use also has a positive impact on the intention to adopt. Because the factor that has the biggest impact on the intention of a farm to adopt is the credibility of the ATSC, it is crucial for extension organizations, such as the ATSC, to make greater efforts to promote the expansion of the HACCP system. Because farmers feel that the implementation of the HACCP system is an instrumental strategy for coping with the high intensity of competition within the industry, they attempt to gain a competitive edge through the production of safe livestock products.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.102-102
• /
• 2018

Electronic industry had required the finer size and the higher performance of the device. Therefore, 3-D die stacking technology such as TSV (through silicon via) and micro-bump had been used. Moreover, by the development of the 3-D die stacking technology, 3-D structure such as chip to chip (c2c) and chip to wafer (c2w) had become practicable. These technologies led to the appearance of HBM (high bandwidth memory). HBM was type of the memory, which is composed of several stacked layers of the memory chips. Each memory chips were connected by TSV and micro-bump. Thus, HBM had lower RC delay and higher performance of data processing than the conventional memory. Moreover, due to the development of the IT industry such as, AI (artificial intelligence), IOT (internet of things), and VR (virtual reality), the lower pitch size and the higher density were required to micro-electronics. Particularly, to obtain the fine pitch, some of the method such as copper pillar, nickel diffusion barrier, and tin-silver or tin-silver-copper based bump had been utillized. TCB (thermal compression bonding) and reflow process (thermal aging) were conventional method to bond between tin-silver or tin-silver-copper caps in the temperature range of 200 to 300 degrees. However, because of tin overflow which caused by higher operating temperature than melting point of Tin ($232^{\circ}C$), there would be the danger of bump bridge failure in fine-pitch bonding. Furthermore, regulating the phase of IMC (intermetallic compound) which was located between nickel diffusion barrier and bump, had a lot of problems. For example, an excess of kirkendall void which provides site of brittle fracture occurs at IMC layer after reflow process. The essential solution to reduce the difficulty of bump bonding process is copper to copper direct bonding below $300^{\circ}C$. In this study, in order to improve the problem of bump bonding process, copper to copper direct bonding was performed below $300^{\circ}C$. The driving force of bonding was the self-annealing properties of electrodeposited Cu with high defect density. The self-annealing property originated in high defect density and non-equilibrium grain boundaries at the triple junction. The electrodeposited Cu at high current density and low bath temperature was fabricated by electroplating on copper deposited silicon wafer. The copper-copper bonding experiments was conducted using thermal pressing machine. The condition of investigation such as thermal parameter and pressure parameter were varied to acquire proper bonded specimens. The bonded interface was characterized by SEM (scanning electron microscope) and OM (optical microscope). The density of grain boundary and defects were examined by TEM (transmission electron microscopy).

• Korean Journal of Health Education and Promotion
• /
• v.21 no.4
• /
• pp.35-49
• /
• 2004

The purpose of this study was to analyze variables associated with smoking and selected health behaviors. This study targeted adult men and women over 20 of age. The sample population was drawn from the national sample, and the samples were chosen from the telephone book. A total of 1,500 cases were collected through a telephone based interview survey. As a tool for this study, a structured questionnaire was developed. the variables included self-perceived health status, and selected 7 health behaviors; smoking behavior, physical activities, eating habit, weight control, alcohol consumption, stress management, and cancer exam. The healthy life practice actions of Trans-theoretical model have been classified into five stages. Smokers were more likely than non-smokers to positive attitudes toward smoking and the impact of smoking in this study. This means that smokers's awareness toward the impact of smoking is very week. Smoking behavior was significantly related to other health related behaviors based on the correlation analysis. However, gender, engaging in regular physical activities, moderate consumption of alcoholic beverages, and receiving a cancer examination were the variables that can explain and predict a person's stages of adopting a non-smoking behavior. Self perceived health status was closely related to other health behaviors. Gender, age, and monthly household income were important demographic variables that have significant relationship with the self-perceived health status. Among the health behaviors, regular physical activities and weight control were significant predictable variables. Similar results have been found in the National health and Nutrition examination survey in Korea. As a result of this study, it was found that among the selected health behaviors, engaging in physical activity was an important variable to increase positive sense of health and non-smoking behaviors. Educational and policy level input is needed to increase awareness and provide chances to participate in fitness activities. To those who maintain exercise, the environmental support and diffusion of knowledge information and education data should be strengthened. To change attitudes toward smoking, more in-dept awareness campaign and education should be provided according to people's different behavioral status. In addition, not only diffusing health education data and delivering knowledge information through related programs, but also environmental support system that helps an individual maintain his/her action is required. Such a support system means settlement of the health enhancement base of school, workplace and community should be carried out, and the policy level support and regular programs should be provided and spread to the unit of community.

• Journal of Korea Soil Environment Society
• /
• v.1 no.2
• /
• pp.73-81
• /
• 1996

The self-diffusion coefficients of chloride and tritiated water ranged from 4.8 $\times$ 10-7 to 7.2 $\times$ 10-7 cm2/sec and 5.5 $\times$ 10-5 to 1.6 $\times$ 10-4 cm2/sec for three different depths of soil constituents at about 50% water content by volume, respectively Mobility of solute and water was conducted under steady-state flow conditions in a field soil consisting of 70 cm of clay to silty clay over a medium sand. A steady-state water flow conditions was maintained by applying irrigation water at a constant flux of 2cm per day. The water labeled with chloride and tritium was leached into the plot during the steady-state condition for 87 days. The positions of tritium and chloride as a function of soil depth and the time was measured by extracting samples of the soil solution with suction probes. Extremes in solute displacement occurred at equal and different depths within the plot. An analysis of these measurements indicated the observations of the pore-water velocity and the apparent diffusion coefficient were log normally disturbed. Twenty-four soil suction probes, used to identify the rate at which a solute was displaced in the soil, will yield an estimate of the mean pore-water velocity of this soils within a range of approximately 5% of its true value providing the effects of potential solute-soil interaction are taken into account.

• Korean Journal of Materials Research
• /
• v.19 no.8
• /
• pp.421-426
• /
• 2009

We report on the capacitively coupled O2 plasma etching of PMMA and polycarbonate (PC) with a diffusion pump. Plasma process variables were process pressure and CCP power at 5 sccm $O_2$ gas flow rate. Characterization was done in order to analyze etch rate, etch selectivity, surface roughness, and morphology using stylus surface profilometry and scanning electron microscopy. Self bias decreased with increase of process pressure in the range of 25$\sim$180 mTorr. We found an important result for optimum pressure for the highest etch rate of PMMA and PC, which was 60 mTorr. PMMA and PC had etch rates of 0.46 and 0.28 ${\mu}m$/min under pressure conditions, respectively. More specifically, etch rates of the materials increased when the pressure changed from 25 mTorr to 60 mTorr. However, they reduced when the pressure increased further after 60 mTorr. RMS roughnesses of the etched surfaces were in the range of 2.2$\sim$2.9 nm. Etch selectivity of PMMA to a photoresist was $\sim$1.5:1 and that of PC was $\sim$0.9:1. Etch rate constant was about 0.04 ${\mu}m$/minW and 0.02 ${\mu}m$/minW for PMMA and PC, respectively, with the CCP power change at 5 sccm $O_2$ and 40 mTorr process pressure. PC had more erosion on the etched sidewall than PMMA did. The OES data showed that the intensity of the oxygen atomic peak (777.196 nm) proportionally increased with the CCP power.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.6
• /
• pp.269-275
• /
• 2005

Ni/Ni-aluminide/Ti/Ti-aluminide laminate composite, considered as a functionally gradient material, was manufactured by thin foil hot press technique. Thick intermetallic layers of NiAl and $TiAl_3$ were formed by a self-propagating high-temperature synthesis (SHS) reaction, and thin continuous taters of $Ni_3Al$ and TiAl were formed by a solid-state diffusion. Fracture resistance with loading along the crack arrester direction is higher than crack divider direction due to the interruption of crack growth in metal layers. The $Ni_3Al$ and NiAl intermetallic layer showed cleavage and intergranular fracture behavior, respectively, while the fracture mode of $TiAl_3$ layer was found to be an intragranular cleavage. The debonding between metal and intermetallic layer and the pores were observed in the Ni/Ni-aluminide layers, resulting in the lower fracture resistance. With the results of acoustic emission (AE) source characterization the real time of failure and the effect of AE to crack growth could be monitored.