• 공업화학
• /
• 제32권6호
• /
• pp.695-699
• /
• 2021

본 연구에서는, 노후된 엔진을 사용하는 트럭 및 특수차량에서 배출되는 NO_x 및 PM을 동시에 제거하기 위해 SDPF 후처리 시스템 연구를 수행하였다. 우선, SDPF의 SCR 촉매를 선정하기 위해서, V/TiO₂와 Cu-zeolite 촉매의 de-NO_x 성능을 비교하였으며, SCR 촉매특성분석은 BET, XRD 및 NH₃-TPD를 통해 분석하였다. 촉매 활성시험 결과, Cu-zeolite 촉매가 가장 우수한 내열성을 보여주었다. 최적의 SDPF 코팅을 위해서, 목표로 설정된 입자 크기에 맞추어 슬러리를 제조하였다. SCR 코팅량에 따른 SDPF의 코팅안정성과 배압 결과, SDPF 촉매를 로딩량별로 A, B, C 샘플을 제작하여 코팅안정성과 배압 및 de-NOx 성능을 비교한 결과 B 샘플에서에서 가장 우수한 결과를 보였다. 최적 SDPF 후처리시스템에 대해 엔진동력계 시험을 실시하였으며, 시험결과 Eu-5 규제를 만족하였다.

• 한국군사과학기술학회지
• /
• 제25권3호
• /
• pp.251-258
• /
• 2022

Infrared stealth technology used in aircraft is applied to reduce the infrared signal by controlling surface temperature and emissivity using internal heat sink, low emissivity material or metamaterial. However, there is one part of the aircraft where the use of this technology is limited, and that is the radome. Especially, radome should have transmittance for the specific radio frequency, therefore, common stealth technology such as emissivity control surfaces cannot be applied to radome surface. In this study, we developed metal nano-coating for infrared stealth which is applicable to radome surface. We designed slot-type pattern for frequency selective transmission in X-band, and also controlled thickness of metal nano-coating for long wavelength infrared emissivity control. As a result, our infrared stealth surface for radome has 93.2 % transmittance in X-band and various infrared emissivities from 0.17 to 0.57 according to nano-coatings thickness. Also, we analyzed infrared signature of radome through numerical simulation, and finally reduced contrast radiant intensity by 97.57 % compared to polyurethane surface.

• 대한금속재료학회지
• /
• 제46권5호
• /
• pp.289-295
• /
• 2008

The effect of the alloy elements(Si/Mn) ratio on the coating quality including wettabilty with molten zinc, galvannealing kinetics and crater has been investigated in interstitial-free high strength steel(IFHSS) containing Si and Mn. When the Si/Mn ratio was below 0.75, IF-HSS exhibited a good wettability leading to a good galvannealed coating quality after annealing at $800^{\circ}C$ for 40s in $15%H_2-N_2$ mixed gas with dew point $-60^{\circ}C$. In contrast, the wettability and galvannealed coating quality were deteriorated in the Si/ Mn ratio above 0.75. It is shown that they have relevance to oxides forms by selective oxidation on the steel surface. The oxide particles dispersed on the steel surface with a surface coverage of below 40% resulted in good wettability and galvannealed coating quality. The oxide particle is mainly consisted of $Mn_2SiO_4$ with low contact angle in molten zinc. On the other hand, the continuous oxide layer on the steel surface, such as network- and film-type,caused to poor wettability and galvannealed coating quality. The coverage of oxide layer was above 80%, and its chemical species was $SiO_2$ with high contact angle in molten zinc. Consequently, the Si/Mn alloy ratio played an importance role in galvannealed coating quality of IF-HSS.

• 한국태양에너지학회 논문집
• /
• 제26권1호
• /
• pp.57-64
• /
• 2006

Cr-CrO cermet solar selective coatings with a double cermets layer film structure were prepared using a special direct current (dc) magnetron sputtering technology. The typical films structures from surface to bottom substrate were measured to be an $Al_2O_3$ anti-reflection layer on a double Cr-CrO cermet layer on an Al metal infrared reflection layer. Optical properties of optimized Cr-CrO cermet solar selective coating were absorptance (${\alpha}$) = 0.95 and emittance (${\varepsilon}$) = 0.10 ($100^{\circ}C$). Atomic force microscopy (AFM) image showed that Cr-CrO cermet film was very smooth and their grain size was also very small The results of thermal stability test showed that the Cr-CrO cermet solar selective coatings were stable for use at temperature of $400^{\circ}C$.

• 펄프종이기술
• /
• 제36권5호
• /
• pp.53-61
• /
• 2004

[ $Poly(_{D}-ldactide)\;(_{D}-PLA)$ ] was synthesized to have low molecular weight for miscible blends with a high molecular $poly(_{L}-lactide)\;(_{L} -PLA)$. The blends were prepared by dissolving the two components of $_{L}-PLA\;and\;_{D}-PLA\;(w/w)$ in chloroform (l00/0, 90/10, 70/30, 50/50, 30/70, 0/100). The miscibility of these miscible blends was characterized by gel-permeation chromatography (GPC), differential scanning calorimetry (DSC), and the selective degradability by enzymes (proteinase K, subtilisin and $\alpha$-chymotrypsin). The coating efficiency of PLA blends onto paper was determined and the degrading activity cellulases by on these blends. The miscibility, coating efficiency and enzymatic degradability of these blends were decreased according to increasing of $_{D}-PLA$ blending part. Such results were attributed to the extent of coating application of PLA, with better miscibility (compatibility), coating efficiency and degradability due to a higher $_{L}-PLA$ content.

• 태양에너지
• /
• 제10권1호
• /
• pp.57-62
• /
• 1990

기판물질이 흑색크롬 선택흡수막의 열적 안정성에 미치는 영향이 RBS에 의해서 조사되었 다. 공기중 $450^{\circ}C$에서 24시간 열처리한 시료의 열퇴화를 연구하기 위해 선택흡수막의 기판물질로서는 구리, 니켈, 스텐레스스틸기판이 사용되었다. 기판물질 확산의 실험 결과가 논의되었으며 스텐레스스틸 기판위에 제작된 시로의 기판물질의 확산이 적게 일어났음을 알 수 있었다

• 한국레이저가공학회지
• /
• 제13권1호
• /
• pp.11-15
• /
• 2010

Indium tin oxide (ITO) provides high electrical conductivity and transparency in the visible and near IR (infrared) wavelengths. Thus, it is widely used as a transparent electrode for the fabrication of liquid crystal displays (LCDs) and organic light emitting diode displays (OLRDs), photovoltaic devices, and other optical applications. Lasers have been used for removing coating on polymer substrate for flexible display and electronic industry. In selective removal of ITO layer, laser wavelength, pulse energy, scan speed, and the repetition rate of pulses determine conditions, which are efficient for removal of ITO coating without affecting properties of the polymer substrate. ITO coating removal with a laser is more environmentally friendly than other conventional etching methods. In this paper, pattering of ITO film from polymer substrates is described. The Yb:KGW femtosecond laser processing system with a pulse duration of 250fs, a wavelength of 1030nm and a repetition rate of 100kHz was used for removing ITO coating in air. We can remove the ITO coating using a scanner system with various pulse energies and scan speeds. We observed that the amount of debris is minimal through an optical and a confocal microscope, and femtosecond laser pulses with 1030nm wavelength are effective to remove ITO coating without the polymer substrate ablation.

• 한국표면공학회지
• /
• 제19권3호
• /
• pp.92-108
• /
• 1986

An electroplating on the lead frame fabricated from domestic copper plate was studied experimentally. In this study, nickel was plated on the thin copper lead frame and silver layer was coated on the nickel film in the cyanide electrolyte. The effect of process variables such as current density, plating time, coating thickness and flow rate of electrolytic solution on the properties of coating was investigated. Some samples on each step were fabricated during electroplating. The results obtained from polarization measurement, observation of SEM photograph, adhesion test of coating and microhardness test are as follows. On silver plating, polarization resistance of potentiostatic cathodic polarization curve is reduced as the flow rate of Ag electrolytic solution increases. And above resistance is also reduced when the minor chemicals of sodium cyanide and sodium carbonate are added in potassium silver cyanide bath. The reduced polarization resistance makes silver deposition on the cathode easy. An increase in the current density and the coating thickness causes the particle size of deposit to coarsen, and consequently the Knoop microhardness of the coating decreases. On selective plating an increase in the flow rate of plating solution lead to do high speed plating with high current density. In this case, the surface morphology of deposit is of fine microstructure with high Knoop hardness. An increasing trend of the adhesion of coating was shown with increasing the current density and flow rate of electrolytic solution.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.116-117
• /
• 2006

We investigated selective emitter effect of Porous Silicon (PSI) as antireflection coatings (ARC). The thin PSi layer, less than 100nm, was electrochemically formed by electrochemical method in about $3{\mu}m$ thick $n^+$ emitter on single crystalline silicon wafer (sc-Si). The appropriate PSi formations for selective emitter effect were carried out a two steps. A first set of samples allowed to be etched after metal-contact processing and a second one to evaporate Ag front-side metallization on PSi layer, by evaluating the I-V features The PSi has reflectance less than 20% in wavelength for 450-1000nm and porosity is about 60%. The cell made after front-contact has improved cell efficiency of about in comparison with the one made after PSi. The observed increase of efficiency for samples with PSi coating could be explained not only by the reduction of the reflection loss and surface recombination but also by the increased short-circuit current (Isc) within selective emitter. The assumption was confirmed by numerical modeling. The obtained results point out that it would be possible to prepare a solar cell over 15% efficiency by the proposed simple technology.

• 한국태양에너지학회 논문집
• /
• 제26권3호
• /
• pp.9-16
• /
• 2006

A solar collector surface coated with a low emission material is still imported from other developed countries expensively. Thus it is very significant to develop a new coating method with a cheap alternative coating material instead of the imported high-cost collector surface. A thermal spray method was adopted to coat a cheap Titania on a copper plate. Generally, a new coating on the copper plate was conducted successfully by selecting a proper ratio of carbon and acetylene. By measuring an absorption rate of solar and heat emission rate, all the plate types gained a high absorption rate of 98% approximately, more or less, but all of the types still have a high emission. Finally it was clear that more research is needed to advance the coated-plate to subdue the high emission from the hot plate surface and the higher the Titania's proportion is, the lower the emission is on the surface.