• 한국지진공학회논문집
• /
• 제10권3호
• /
• pp.149-158
• /
• 2006

보 플랜지 절취형(Reduced Beam Section, RBS) 내진 철골모멘트접합부는 국내외의 여러 실험프로그램에서 뛰어난 내진성능을 보여 주었다. 그러나 추가적으로 규명해야할 설계상의 몇몇 이슈들이 아직 남아있다. 그 중의 하나가 패널존의 보에 대한 적정강도이다. 다수의 실험결과가 존재함에도 불구하고 패널존과 보 사이의 적정강도비가 아직까지 명확하게 제시된 바가 없다. 본 연구에서는 독립적으로 수행된 국내외의 광범위한 실험 데이터베이스를 기초로 패널존 강도가 접합부의 내진거동에 미치는 영향을 포괄적으로 분석하였다. 이를 기초로 보의 좌굴을 감소시키는 동시에 충분한 접합부 소성회전능력을 보장할 수 있는 균형패널존의 강도범위를 제안하였다. 아울러 반복재하 실물대 실험결과를 만족스럽게 재현할 수 있는 유한요소모델을 구축한 후 다양한 수치해석을 통하여 실험자료에서 누락된 부분이나 실험적으로는 파악하기 어려운 거동을 고찰하였다. 이 과정에서 오늘날의 강력한 유한요소해석기법을 활용하여 많은 비용이 드는 철골접합부 실물대 내진실험을 보완하거나 적어도 부분적으로 대체할 수 있음을 확인하였다.

• 한국지반공학회논문집
• /
• 제36권6호
• /
• pp.17-34
• /
• 2020

일반적으로 잔교식 구조물의 내진설계를 위한 응답스펙트럼 해석 시 기준서들에서는 지진응답해석을 통해 증폭된 가속도를 입력가속도 활용하도록 제시하고 있으나, 기준서에 따라 방법이 상이하여 설계 시 혼란을 야기할 수 있다. 이에, 본 연구에서는 동적원심모형실험을 통해 지반 내 다양한 깊이에서 지반 가속도를 산정하였으며, 산정된 지반가 속도를 활용하여 응답스펙트럼 해석을 수행하였다. 이후 실험 및 해석을 통해 도출된 잔교식 안벽 구조물의 모멘트 결과를 비교하였으며, 응답스펙트럼 해석 시 적절한 입력지반가속도를 결정하기 위한 방법을 제시하고자 하였다. 실험 및 해석을 비교한 결과, 탄성 지반 스프링을 적용하는 경우 구조물의 고유주기를 가장 적절하게 모사하는 것으로 나타났으며, 상부 지표면에서 증폭된 지진파를 입력가속도로 활용하는 것이 사질토 지반에 관입된 구조물 응답을 가장 합리적으로 모사하는 것으로 나타났다.

• Computers and Concrete
• /
• 제26권6호
• /
• pp.547-563
• /
• 2020

In this paper, the influence of axial compression ratio on the mechanical properties of new type joints of side span of rectangular concrete-filled steel tubular column-H-type steel beam is studied. Two new types of side-span joints of rectangular concrete-filled steel tubular column-H-type steel beam are designed and quasi-static tests of five new type joints with 1:2 scale reduction ratios are performed. The axial compression ratio of joint JD1 is 0.3, 0.4 and 0.5, and the axial compression ratio of joint JD2 is 0.3 and 0.5. In the joint test, different axial forces were applied to the top of the column according to different axial compression ratios, and low-cyclic reciprocating load was applied on the beam. The stress and strain distribution, beam and column deformation, limit state, failure process, failure mechanism, stiffness degradation, ductile deformation and energy dissipation capacity of the joint were measured and analyzed. The results show that: with the increase of axial compression ratio, the ultimate bearing capacity of the joint decreases slightly, the plastic deformation decreases, and the stiffness and ductility decrease. According to the energy dissipation curve of the specimen, the equivalent damping coefficient also increases with the increase of axial compression ratio in a certain range, indicating that the increase of axial compression ratio can improve the seismic performance of the joint to a certain extent. The finite element method is used to simulate the joint test, and the test results are in good agreement with the simulation results.

• Earthquakes and Structures
• /
• 제25권2호
• /
• pp.113-123
• /
• 2023

A novel type of buckling restrained brace with built-up angle steel was developed. The core segment was formed by welding angle steel, and the middle section was reduced by cutting technology to solve the problem that the end of BRB was easy to buckle. The experimental program has been undertaken to study the performance of BRBs with different unbonded materials (silica gel, kraft paper) and different filler materials (ordinary concrete, full light-weight concrete). Four specimens were designed and fabricated for low cycle reciprocating load tests to simulate horizontal seismic action. The failure mode, hysteretic curves, tension-compression unbalance coefficient and other mechanical parameters were compared and analyzed. The finite element software ABAQUS was used to conduct numerical simulation, and the simulation results were compared with the experimental phenomena. The test results indicated that the hysteretic curve of each specimen was plump. Sustaining cumulative strains of each specimen was greater than the minimum value of 200 required by the code, which indicated the ductility of BRB was relatively good. The energy dissipation coefficient of the specimen with silica gel as unbonded material was about 13% higher than that with kraft paper. The experimental results were in good agreement with the simulation results.

• 한국지반환경공학회 논문집
• /
• 제21권7호
• /
• pp.5-16
• /
• 2020

현재 경주지진 및 포항지진 발생으로 내진설계기준이 강화되어 기존 시설물에 대한 내진성능평가를 실시하고 있다. 기존 시설물의 피해를 최소화하면서 국한된 협소한 장소에서 시공이 가능한 마이크로파일공법을 개선하여 지진 시 내진성능효과를 확보하고자 한다. 개선방법은 주 기둥인 연직말뚝 주변에 우산형태로 경사말뚝을 시공하여 말뚝 상부의 사각접시형 플레이트에서 말뚝을 모두 일체화하는 것이다. 본 논문에서는 수치해석으로 사질토지반에서 다양한 지진파에 대해 우산형 마이크로파일의 수평변위 거동을 분석하였다. 수치해석 결과, 지반이 연약할수록 우산형 마이크로파일의 수평저항력의 효과가 우수하였다. 경사말뚝의 근입심도에 따른 분석결과, 동일한 지반강도에서 근입심도가 15m 이상일 경우에 수평변위 저감 효과가 뚜렷했으며, N치 30 이상의 지반에 정착하면 지진 시에 효과가 있는 것으로 확인되었다. 마이크로파일의 근입심도와 수평변위 억제효과가 비례하였으며, 대체적으로 지반이 약할수록 변위억제 효과가 컸다. 우산형 마이크로파일은 수직말뚝이 모멘트에 대한 저항을 하고, 경사말뚝이 축력에 대한 저항을 하는 복합저항효과가 있었다.

• Earthquakes and Structures
• /
• 제27권2호
• /
• pp.143-154
• /
• 2024

Friction pendulums typically suffer from poor uplift-restraining. To improve the uplift-restraining and enhance the energy dissipation capacity, this article proposed a composite isolation device based on electromagnetic forces. The device was constructed based on a remote control system to achieve semi-active control of the composite isolation device. This article introduces the theory and design of an electromagnetic chuck-friction pendulum system (ECFPS) and derives the theoretical equation for the ECFPS based on Maxwell's electromagnetic attraction equation to construct the proposed model. By conducting 1:3 scale tests on the electromagnetic device, the gaps between the practical, theoretical, and simulation results were analyzed, and the accuracy and effectiveness of the theoretical equation for the ECFPS were investigated. The hysteresis and uplift-restraining performance of ECFPS were analyzed by adjusting the displacement amplitude, vertical load, and input current of the simulation model. The data obtained from the scale test were consistent with the theoretical and simulated data. Notably, the hysteresis area of the ECFPS was 35.11% larger than that of a conventional friction pendulum. Lastly, a six-story planar frame structure was established through SAP2000 for a time history analysis. The isolation performances of ECFPS and FPS were compared. The results revealed that, under horizontal seismic action, the horizontal seismic response of the bottom layer of the ECFPS isolation structure is greater than that of the FPS, the horizontal vibration response of the top layer of the ECFPS isolation structure is smaller than that of the FPS, and the axial force at the bottom of the columns of the ECFPS isolation structure is smaller than that of the FPS isolation structure. Therefore, the reliable uplift-restraining performance is facilitated by the electromagnetic force generated by the device.

• 한국지진공학회논문집
• /
• 제22권5호
• /
• pp.261-269
• /
• 2018

This study examines earthquake-induced sloshing effects on liquid storage tanks using computation fluid dynamics. To achieve this goal, this study selects an existing square steel tank tested by Seismic Simulation Test Center at Pusan National University as a case study. The model validation was firstly performed through the comparison of shaking table test data and simulated results for the water tank subjected to a harmonic excitation. For a realistic estimation of the wall pressure response of the water tank, three recorded earthquakes with similar peak ground acceleration are applied:1940 El Centro earthquake, 2016 Gyeongju earthquake, and 2017 Pohang earthquake. Wall pressures monitored during the dynamic analyses are examined and compared for different earthquake motions and monitoring points, using power spectrum density. Finally, the maximum dynamic pressure for three earthquakes is compared with the design pressure calculated from a seismic design code. Results indicated that the maximum pressure from the El Centro earthquake exceeds the design pressure although its peak ground acceleration is less than 0.4 g, which is the design acceleration. On the other hand, the maximum pressure due to two Korean earthquakes does not reach the design pressure. Thus, engineers should not consider only the peak ground acceleration when determining the design pressure of water tanks.

• Smart Structures and Systems
• /
• 제8권5호
• /
• pp.501-524
• /
• 2011

Recent studies have discovered that a conventional passive isolation system may suffer from an excessive isolator displacement when subjected to a near-fault earthquake that usually has a long-period velocity pulse waveform. Semi-active isolation using variable friction dampers (VFD), which requires a suitable control law, may provide a solution to this problem. To control the VFD in a semi-active isolation system more efficiently, this paper investigates experimentally the possible use of a control law whose control logic is similar to that of the anti-lock braking systems (ABS) widely used in the automobile industry. This ABS-type controller has the advantages of being simple and easily implemented, because it only requires the measurement of the isolation-layer velocity and does not require system modeling for gain design. Most importantly, it does not interfere with the isolation period, which usually decides the isolation efficiency. In order to verify its feasibility and effectiveness, the ABS-type controller was implemented on a variable-friction isolation system whose slip force is regulated by an embedded piezoelectric actuator, and a seismic simulation test was conducted for this isolation system. The experimental results demonstrate that, as compared to a passive isolation system with various levels of added damping, the semi-active isolation system using the ABS-type controller has the better overall performance when both the far-field and the near-fault earthquakes with different PGA levels are considered.

• Steel and Composite Structures
• /
• 제22권4호
• /
• pp.797-820
• /
• 2016

This paper simulates the hysteretic behavior of steel reinforced recycled concrete (SRRC) columns under cyclic loads using OpenSees software. The effective fiber model and displacement-based beam-column element in OpenSees is applied to each SRRC columns. The Concrete01 material model for recycled aggregate concrete (RAC) and Steel02 material model is proposed to perform the numerical simulation of columns. The constitutive models of RAC, profile steel and rebars in columns were assigned to each fiber element. Based on the modelling method, the analytical models of SRRC columns are established. It shows that the calculated hysteresis loops of most SRRC columns agree well with the test curves. In addition, the parameter studies (i.e., strength grade of RAC, stirrups strength, steel strength and steel ratio) on seismic performance of SRRC columns were also investigated in detail by OpenSees. The calculation results of parameter analysis show that SRRC columns suffered from flexural failure has good seismic performance through the reasonable design. The ductility and bearing capacity of columns increases as the increasing magnitude of steel strength, steel ratio and stirrups strength. Although the bearing capacity of columns increases as the strength grade of RAC increases, the ductility and energy dissipation capacity decreases gradually. Based on the test and numerical results, the flexural failure mechanism of SRRC columns were analysed in detail. The computing theories of the normal section of bearing capacity for the eccentrically loaded columns were adopted to calculate the nominal bending strength of SRRC columns subjected to vertical axial force under lateral cyclic loads. The calculation formulas of horizontal bearing capacity for SRRC columns were proposed based on their nominal bending strength.

• 한국지진공학회논문집
• /
• 제16권2호
• /
• pp.15-24
• /
• 2012

본 논문은 전단벽과 슬래브, 인방보의 연결부재로 구성되는 독특한 구조형식으로 이루어진 국내 철근콘크리트(RC)조 공동주택의 지진거동을 정확하게 평가하기 위한 방법을 제시하기 위한 기초연구이다. 이를 위하여 인방보의 유무에 따른 RC조 전단벽식 부분구조 실험체 2개에 대하여 선형 스프링모델에 의한 비선형 정적해석을 실시하고 기존의 실험결과와 비교 분석하여 그 신뢰성을 검증 하였다. 인방보가 없는 실험체의 경우, 해석결과가 실험결과에 의한 비선형 거동을 정확히 모사하고 있는 것으로 나타났다. 반면, 인방보가 있는 실험체의 경우, 해석결과의 경우, 정방향 가력시 실험결과 보다 작은 실험체의 변형으로 인방보에 의한 커플링 효과를 기대할 수 없게 되면서, 해석결과가 실험결과보다 재하시의 동일 변형에서의 내력과 잔류변형 등을 작게 평가하는 것으로 나타났다.