• 한국방재학회 논문집
• /
• 제5권1호
• /
• pp.23-32
• /
• 2005

1995년 일본 고베 대지진 발생 이후 한국정부는 국내 시설물에 대한 내진설계분야 및 지진피해 최소화 방안에 대한 연구를 지속적으로 진행해왔으며, 현재까지 괄목할 만한 많은 성과를 내고 있다. 그렇지만, 국내비탈면과 같은 구조물들은 여전히 내진설계가 적용되지 않고 있으며, 일부 기관에서만 설계자의 판단에 의해 비탈면 내진설계가 적용되고 있는 실정이다. 본 연구에서는 국내외 비탈면 내진설계에 대한 연구 결과를 소개하고 국내비탈면에 적용할 수 있는 내진설계 방안을 제시하였다. 비탈면 내진설계 적용범위는 경제성, 비탈면의 중요도 및 복구의 용이성 등을 고려하여 공학자가 내진설계 여부를 판단하도록 하는 것이 바람직하며, 우리나라 비탈면의 내진설계 적용 범위 및 관련 기준도 지진관련 자료를 축적하여 향후 단계적으로 정립하는 것이 바람직 할 것으로 판단된다.

• 한국지진공학회논문집
• /
• 제9권3호
• /
• pp.23-32
• /
• 2005

편심이 있는 구조물이 지진하중을 받는 경우 비틀림의 발생으로 특정부재에 응력 및 변위가 집중되고 이는 전혀 예상치 못한 구조물의 파괴를 유발할 수 있다. 본 연구에서는 각 횡저항 부재의 한계 변위를 기반으로 하여 구조물 전체의 횡변위와 비틀림각의 관계도(D-R Relationship: Displacement-Rotation Relationship)를 작성하고 변위스펙트럼을 이용하여 내진성능평가를 수행하는 방법을 제안한다. 제안된 내진성능평가의 방법은 시간이력해석의 결과를 이용해서 검증하였다. 또한 다양한 지진수준에 대해 구조물의 다른 성능수준을 기준으로 하는 다단계 내진성능평가를 수행하였다. 최종적으로 그 결과를 기준으로 D-R 관계도를 이용한 내진보강 전략을 제시하였다. 내진보강은 각 부재의 강도/강성을 증가시키는 방법과 연성도를 증가시키는 두 가지의 방법을 사용하였다. 특히 강도/강성을 증가시키는 내진보강 전략에서는 보강의 최적화를 위하여 보강전략을 최적화 문제로 구성하고 BFGS Quasi-Newton method를 이용하여 최적보강전략을 수립하는 과정을 제시하였다.

• Structural Engineering and Mechanics
• /
• 제59권3호
• /
• pp.387-401
• /
• 2016

This paper takes a half-through steel truss arch bridge as an example. A seismic analysis is conducted with nonlinear finite element method. Contrast models are established to discuss the effect of simplified method for main girder on the accuracy of the result. The influence of seismic wave direction and wave-passage on seismic behaviors are analysed as well as the superstructure and arch ring interaction which is mostly related with the supported bearings and wind resistant springs. In the end, the application of cable-sliding aseismic devices is discussed to put forward a layout principle. The main conclusions include: (1) The seismic response isn't too distinctive with the simplified method of main girder. Generally speaking, the grillage method is recommended. (2) Under seismic input from different directions, arch foot is usually the mostly dangerous section. (3) Vertical wave input and horizontal wave-passage greatly influence the seismic responses of arch ring, significantly increasing that of midspan. (4) The superstructure interaction has an obvious impact on the seismic performance. Half-through arch bridges with long spandrel columns fixed has a less response than those with short ones fixed. And a large stiffness of wind resistant spring makes the the seismic responses of arch ring larger. (5) A good isolation effectiveness for half-through arch bridge can be achieved by a reasonable arrangement of CSFABs.

• Computers and Concrete
• /
• 제30권2호
• /
• pp.113-126
• /
• 2022

Reinforced concrete bearing walls (RCBWs) are one of the most applicable structural systems. Therefore, vulnerability analysis and rehabilitation of the RCBW system are of great importance. In the present study, in order to the more precise investigation of the performance of this structural resistant system, pushover and nonlinear time history analyses based on several assumptions drawing upon experimental research were performed on several models with different stories. To validate the nonlinear analysis method, the analytical and experimental results are compared. Vulnerability evaluation was carried out on two seismic hazard levels and three performance levels. Eventually, the need for seismic rehabilitation with the basic safety objective (BSO) was investigated. The obtained results showed that the studied structures satisfied the BSO of the seismic rehabilitation guidelines. Consequently, according to the results of analyses and the desired performance, this structural system, despite its high structural weight and rigid connections and low flexibility, has integrated performance, and it can be a good option for earthquake-resistant constructions.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 토목섬유 학술발표회 논문집
• /
• pp.69-83
• /
• 1999

Soil-reinforced segmental retaining walls(SRW) have been proven to be high earthquake-resistant structure during recent earthquakes in United States and Japan. The mechanicals behavior of the SRWs under seismic loading, however, has not been fully understood. Although the seismic design issues for the civil engineering structures have gained much attention in Korea due to the increase in frequency of earthquake occurrence, the seismic design for the SRWs has not been being implemented. This study has been undertaken with the aim of developing a more rational seismic design/analysis method for soil-reinforced segmental retaining walls. This paper present fundamentals of current seismic design/analysis method and the results of a comparative study between NCMA and FHWA design guidelines, Practical implications of the findings from this study are discussed in great detail.

• 대한건축학회논문집:구조계
• /
• 제36권1호
• /
• pp.137-146
• /
• 2020

In this study, various application schemes of seismic isolation system which can be applied to Hanok have been studied by analyzing its structural characteristics under seismic load. Structural stability of Hanok is more required against seismic load as Hanok becomes long-spanned and multi-storied. To meet this goal, it becomes necessary to study more advanced technology such as seismic isolation design as well as seismic control design and seismic resistant design suitable to Hanok. Seismic isolation systems have been successfully applied to RC and steel structures to improve structural performance during earthquakes. Based on these previous study, we proposed four application schemes of seismic isolation design suitable for Hanok and analyzed their structural characteristics and applicability to Hanok in conceptual level based on its structural characteristics. The proposed four schemes are base isolation method, ground isolation method, roof isolation method and intermediate-story isolation method. The applicability of the proposed method was evaluated by performing boundary nonlinear dynamic analysis to the typical Hanok for the two types of isolation method, that is, ground isolation method and roof isolation method, and the results showed that the proposed methods produced good performance enough to be applied to Hanok.

• Structural Engineering and Mechanics
• /
• 제71권4호
• /
• pp.417-432
• /
• 2019

Seismic performance analysis of steel-brace reinforced concrete (RC) frame using topology optimization in highly seismic region was discussed in this research. Topology optimization based on truss-like material model was used, which was to minimum volume in full-stress method. Optimized bracing systems of low-rise, mid-rise and high-rise RC frames were established, and optimized bracing systems of substructure were also gained under different constraint conditions. Thereafter, different structure models based on optimized bracing systems were proposed and applied. Last, structural strength, structural stiffness, structural ductility, collapse resistant capacity, collapse probability and demolition probability were studied. Moreover, the brace buckling was discussed. The results show that bracing system of RC frame could be derived using topology optimization, and bracing system based on truss-like model could help to resolve numerical instabilities. Bracing system of topology optimization was more effective to enhance structural stiffness and strength, especially in mid-rise and high-rise frames. Moreover, bracing system of topology optimization contributes to increase collapse resistant capacity, as well as reduces collapse probability and accumulated demolition probability. However, brace buckling might weaken beneficial effects.

• Earthquakes and Structures
• /
• 제4권4호
• /
• pp.341-363
• /
• 2013

Earthquake response calculation, parametric analysis and seismic parameter optimization of base-isolated structures are some critical issues for seismic design of base-isolated structures. To calculate the earthquake responses for such non-symmetric and non-classical damping linear systems and to implement the earthquake resistant design codes, a modified complex mode superposition design response spectrum method is put forward. Furthermore, to do parameter optimization for base-isolation structures, a graphical approach is proposed by analyzing the relationship between the base shear ratio of a seismic base-isolation floor to non-seismic base-isolation one and frequency ratio-damping ratio, as well as the relationship between the seismic base-isolation floor displacement and frequency ratio-damping ratio. In addition, the influences of mode number and site classification on the seismic base-isolation structure and corresponding optimum parameters are investigated. It is demonstrated that the modified complex mode superposition design response spectrum method is more precise and more convenient to engineering applications for utilizing the damping reduction factors and the design response spectrum, and the proposed graphical approach for parameter optimization of seismic base-isolation structures is compendious and feasible.

• 한국구조물진단유지관리공학회 논문집
• /
• 제6권2호
• /
• pp.121-126
• /
• 2002

Due to few earthquakes in our country, one generally has thought to be safe from earthquakes. However, severe earthquakes occurred in Dangsan and Hyogohyeon which one had regarded as the zone that had not been risky for earthquakes, so that so many people died and a lot of buildings and bridges were destroyed. This event surprised our country and we undertook preparation for earthquakes on the full scale. The concept of seismic design was induced in the country which was poor in it for the scarcity of recognition and insufficiency of funds. Recently, many specialists are enforcing the provisions of seismic design. Therefore, this study introduces the method which combines PC-LEADeR( design program for L.R.B.) with LUSAS(linear elastic analysis) and performs the seismic isolation design more elaborately and simply. It verifies the propriety of that method, and it also examine the factors that affect the response of the bridges. Seismic isolation design for bridge using L.R.B. provides both economical efficiency and superior seismic performance. Second, the results between by the method proposed and by time history analysis have 20% error at the maximum. That is, the method proposed very appropriate.

• 한국전산구조공학회논문집
• /
• 제25권2호
• /
• pp.149-154
• /
• 2012

도로교설계기준 내진설계편은 붕괴방지수준의 확보를 설계절차에 의해 규정하고 있는 반면 기능수행수준의 확보에 대한 요구사항은 명확하게 제시하고 있지 않다. 붕괴방지수준의 확보를 위해 기본적으로 제시된 설계방법은 응답수정계수를 사용하는 스펙트럼해석법으로, 기능수행수준은 설계과정에 적용되는 위험도계수와 응답수정계수에 의해 결정 되어진다. 위험도계수는 교량의 중요도에 따라 단순하게 적용할 수 있으나 중약진지역에서의 응답수정계수 적용은 설계조건에 따라 다른 결과를 갖게 된다. 이 연구에서는 중약진지역의 일반 도로교량을 대상으로 내진설계를 수행하여 기능수행수준의 결정과정을 검토하고, 이 결과를 토대로 기능수행수준의 확보와 관련하여 내진설계편에 보완해야 하는 사항을 제시하였다.