• Journal of Powder Materials
• /
• v.15 no.5
• /
• pp.378-385
• /
• 2008

This article presents the successful consolidation of the mixed Co and Diamond powders for a drilling segment by the combined application of magnetic pulsed compaction (MPC) and subsequent sintering, and their properties were analyzed. Homogeneous hardness (Hv 220) and density (97%) of sintered bulks fabricated by MPC were obtained by the new technique, where higher pressure has been employed for short period of time than that of general process. A fine microstructure and homogeneous hardness in the consolidated bulk were observed without cracks. Relatively higher drilling speed of 9.61 cm/min and life time of 6.55 m were found to the MPCed specimens, whereas the value of the specimens fabricated by general process was 11.71 cm/min and 7.96 m, respectively. A substantial improvement of mechanical properties of segment was achieved through this study.

• Progress in Medical Physics
• /
• v.21 no.2
• /
• pp.137-144
• /
• 2010

The purpose of this study was to evaluate the usefulness of reducing of craniofacial radiation dose using automatic exposure control (AEC) technique in the 64 multi-detector computed tomography (MDCT). We used SOMATOM Definition 64 multi-detector CT, and head of whole body phantom (KUPBU-50, Kyoto Kagaku CO. Ltd). The protocol were helical scan method with 120 kVp, 1 sec of rotation time, 5 mm of slice thickness and increment, 250 mm of FOV, $512{\times}512$ of matrix size, $64{\times}0.625\;mm$ of collimation, and 1 of pitch. The evaluation of dose reducing effect was compared the fixed tube current of 350 with AEC technique. The image quality was measured the noise using standard deviation of CT number. The range of craniofacial bone was to mentum end from calvaria apex, which devided three regions: calvaria~superciliary ridge (1 segment), superciliary ridge~acanthion (2 segment), and acanthion~mentum (3 segment). In the fixed tube current technique, CTDIvol was 57.7 mGy, DLP was $640.2\;mGy{\cdot}cm$ in the all regions. The AEC technique was showed that 1 segment were 30.7 mGy of CTDIvol, 340.7 $mGy{\cdot}cm$ of DLP, 2 segment were 46.5 mGy of CTDIvol, $515.0\;mGy{\cdot}cm$ of DLP, and 3 segment were 30.3 mGy of CTDIvol, $337.0\;mGy{\cdot}cm$ of DLP. The standard deviation of CT number was 2.622 with the fixed tube current technique and 3.023 with the AEC technique in the 1 segment, was 3.118 with the fixed tube current technique and 3.379 with the AEC technique in the 2 segment, was 2.670 with the fixed tube current technique and 3.186 with the AEC technique in the 3 segment. The craniofacial radiation dose using AEC Technique in the 64 MDCT was evaluated the usefulness of reducing for the eye, the parotid and thyroid with high radiation sensitivity particularly.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2012.03a
• /
• pp.105-105
• /
• 2012

기능성 아웃도어 제품을 제조하기 위해서 사용되어지는 멤브레인은 크게 미세다공형과 친수무공형으로 구분할 수 있다. 최근에는 소비자들이 기능성 아웃도어에 쾌적성을 요구하고 있으며, 그 측면에서 본다면 미세다공형 멤브레인이 친수무공형보다 유리하다. 기존의 미세다공형 멤브레인은 고가이며, casting이 불가능한 단점을 가지고 있다. 본 연구에서는 분자구조 및 유화제 첨가에 따른 casting이 가능한 미세다공형 폴리우레탄 멤브레인의 특성에 대하여 연구하였다. Casting용 미세다공형 폴리우레탄은 soft segment와 hard segment의 비가 1/2일 때, 그리고 사용되는 용제가 MEK 단독일 때 안정적인 반응성과 이상적인 필름의 물성을 보이는 것을 확인 하였으며, 수지에 첨가되는 분산유화제의 양이 10%이상일 때 상분리 현상이 발생하지 않음을 확인 할 수 있었다. 개발된 수지의 적용성을 평가한 결과, J-knife를 이용하여 knife over roll 방식으로 25~35$g/m^2$ (dry add on)를 도포하여 $80/120/140^{\circ}C{\times}10m/min$의 다단건조 공정으로 진행했을 때 최적의 물성을 얻을 수 있었다.

• Korean Journal of Applied Biomechanics
• /
• v.28 no.4
• /
• pp.213-218
• /
• 2018

Objective: The purpose of this study was to examine the effect of the core muscle strength enhancement of the elderly on 8 weeks training using the core exercise equipment for the elderly on the ability to control the whole-body center of mass in posture stabilization. Method: 16 females (10 exercise group, 6 control group) participated in this study. Exercise group took part in the core strength training program for 8 weeks with total of 16 repetitions (2 repetitions per week) using a training device. External perturbation during standing as pulling force applied at the pelvic level in the anterior direction was provided to the subject. In a UCM model, the controller selects within the space of elemental variables a subspace (a manifold, UCM) corresponding to a value of a performance variable that needs to be stabilized. In the present study, we were interested in how movements of the individual segment center of mass (elemental variables) affect the whole-body center of mass (the performance variable) during balance control. Results: At the variance of task-irrelevant space, there was significant $test^*$ group interactions ($F_{1,16}=7.482$, p<.05). However, there were no significant main effect of the test ($F_{1,16}=.899$, p>.05) and group ($F_{1,16}=1.039$, p>.05). At the variance of task-relevant space, there was significant $test^*$ group interactions ($F_{1,16}=7.382$, p<.05). However, there were no significant main effect of the test ($F_{1,16}=.754$, p>.05) and group ($F_{1,16}=1.106$, p>.05). Conclusion: The results of this study showed that the 8 weeks training through the core training equipment for the elderly showed a significant decrease in the $Vcm_{TIR}$ and $Vcm_{TR}$. This result indicates that the core strength training affects the trunk stiffness control strategy to maintain balance in the standing position by minimizing total variability of individual segment CMs.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2014.11a
• /
• pp.55-55
• /
• 2014

• Journal of the Korean GEO-environmental Society
• /
• v.7 no.2
• /
• pp.67-76
• /
• 2006

For a hydro power plant project, the headrace tunnel having a finished diameter of 3.3 m was constructed in volcanic rocks with well-developed vertical joint and high groundwater table. The intake facility was located 20.3km upstream of the powerhouse and headrace tunnel of 20km in length and penstock of 440m in height connected the intake and the powerhouse. The typical caldera lake, Lake Toba set the geology at the site the caving of the ground caused tension cracks in the vertical direction to be developed and initial stresses at the ground to be released. High groundwater table(the maximum head of 20bar) in the area of well-connected vertical joints delayed the progress of tunnel excavation severely due to the excessive inflow of groundwater. The excavation of tunnel was made using open-shield type TBM and mucking cars on the rail. High volume of water inflowraised the water level inside tunnel to 70cm, 17% of tunnel diameter (3.9m) and hindered the mucking of spoil under water. To improve the productivity, several adjustments such as modification of TBM and mucking cars and increase in the number of submersible pumps were made forthe excavation of severe water inflow zone. Since the ground condition encountered during excavation turned out to be much worse, it was decided to adopt PC segment lining instead of RC lining. Besides, depending on the conditions of the water inflow, rock mass condition and internal water pressure, one of the invert PC segment lining with in-situ RC lining, RC lining and steel lining was applied to meet the site specific condition. With the adoption of PC segment lining, modification of TBM and other improvement, the excavation of the tunnel under severe groundwater condition was successfully completed.

• Mycobiology
• /
• v.32 no.3
• /
• pp.123-127
• /
• 2004

Sweet persimmons have been increasingly cultivated in the southern part of Korea. However, anthracnose disease caused by Colletotrichum species is one of the major hindrances in cultivation and productions. In this study, we used polymerase chain reaction(PCR) to detect Colletotrichum species with the AFLP(amplified fragment length polymorphism) method. In AFLP, we used E3(5'-GACTGCGTACCAATTCTA-3') and M1(5'-GATGAGTCCTGAGTAACAG-3') primer combination and, as a result, 262 bp segment was observed in Colletotrichum species only. Specific PCR primers were designed from the sequence data and used to detect the presence of the fungus in genomic DNA isolated from symptomless sweet persimmon plants. Based on sequence data for specific segments, Co.B1(5'-GAGAGAGTAGAATTGCGCTG-3') and Co.B2(5'-CTACCATTCTTCTA GGTGGG-3') were designed to detect Colletotrichum species. The 220 bp segment was observed in Colletotrichum species only, but not in other fungal and bacterial isolates.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.43 no.2
• /
• pp.120-123
• /
• 1998

Based on the co-linearity in the Triticeae, comparative RFLP analysis of 2M chromosome of Ae. comosa Sibth et Sm. was performed with 2MS and 2M additional lines of Triticum aestivum L. cv. Chinese Spring. Among the wheat RFLP probes conserved in the short arms of wheat chromosome 2, those above psr912 were located on the long arms of 2M in Aegilops comosa. The rest probes on the short arm and all the probe sequences on the long arm of group 2 chromosome in wheat were conserved on the equivalent chromosomal position in Aegilops comosa. So, it is apparent that some chromosomal segment from the short arm had been transferred to long arm while reconstructing 2M chromosome relative to wheat chromosomes. The break-point was located between psr912 and psr131 of the short arm. This rearrangement of chromosome 2M might be a molecular evidence of the M genome speciation from an ancestral type.

• Polymer(Korea)
• /
• v.29 no.3
• /
• pp.253-259
• /
• 2005

Polyurethanes, synthesized by polyester polyols and aliphatic or aromatic diisocyanates for a crease resist finishing agent, were prepared by two-step reactions, that is, prepolymer synthesis and chain extension. The structures of synthesized polyurethanes were confirmed by the measurement of FT-IR and $^1H$-NMR spectrometer. The number average molecular weight ($\bar{M}_n$) and the weight average molecular weight ($\bar{M}_w$) of the polyurethane with aromatic diisocyanate (MDI) were higher than those of the synthesized polyurethanes with aliphatic diisocyanate (HDI, $H_{12}MDI$). The glass transition temperatures ($T_g$) of soft segments in polyurethanes with MDI, HDI, $H_{12}MDI$ were -25,-42 and -50$^{circ}C$, respectively. In the polyurethanes obtained by two-step reaction, thermal stability and tensile strength increased with increasing hard segment contents, whereas elongation at break decreased with increasing hard segment contents.

• The Korean Journal of Physiology and Pharmacology
• /
• v.23 no.3
• /
• pp.203-217
• /
• 2019

The present study was designed to examine the effect of heme oxygenase-1 (HO-1) induction by cobalt protoporphyrin (CoPP) on the cardiac functions and morphology, electrocardiogram (ECG) changes, myocardial antioxidants (superoxide dismutase [SOD] and glutathione [GSH]), and expression of heat shock protein (Hsp) 70 and connexin 43 (Cx-43) in myocardial muscles in isoproterenol (ISO) induced myocardial infarction (MI). Thirty two adult male Sprague Dawely rats were divided into 4 groups (each 8 rats): normal control (NC) group, ISO group: received ISO at dose of 150 mg/kg body weight intraperitoneally (i.p.) for 2 successive days; ISO + Trizma group: received (ISO) and Trizma (solvent of CoPP) at dose of 5 mg/kg i.p. injection 2 days before injection of ISO, with ISO at day 0 and at day 2 after ISO injections; and ISO + CoPP group: received ISO and CoPP at a dose of 5 mg/kg dissolved in Trizma i.p. injection as Trizma. We found that, administration of ISO caused significant increase in heart rate, corrected QT interval, ST segment, cardiac enzymes (lactate dehydrogenase, creatine kinase-muscle/brain), cardiac HO-1, Hsp70 with significant attenuation in myocardial GSH, SOD, and Cx-43. On the other hand, administration of CoPP caused significant improvement in ECG parameters, cardiac enzymes, cardiac morphology; antioxidants induced by ISO with significant increase in HO-1, Cx-43, and Hsp70 expression in myocardium. In conclusions, we concluded that induction of HO-1 by CoPP ameliorates ISO-induced myocardial injury, which might be due to up-regulation of Hsp70 and gap junction protein (Cx-43).