• Clean Technology
• /
• v.29 no.1
• /
• pp.31-38
• /
• 2023

Due to water shortages caused by water pollution and climate change, total organic carbon (TOC) standards have been implemented for wastewater discharged from public sewage treatment facilities. Furthermore, there is a growing interest and body of research pertaining to the reuse of sewage treatment water as a secure alternative water resource. The membrane bio-reactor (MBR) method is commonly used for advanced wastewater treatment because it can remove organic and inorganic ions and it does not require or emit any chemicals. However, the MBR process uses a separation membrane (MF), which requires frequent film cleaning due to fouling caused by a high concentration of mixed liquor suspended solid (MLSS). In this study, process improvement and microbubble cleaning efficiency were evaluated to improve the differential pressure, water flow, and MF fouling, which are the biggest disadvantages of operating the MF. The existing MBR method was improved by installing a precipitation tank between the air tank and the MBR tank in which raw water was introduced. Microbubbles were injected into a separation membrane tank into which the supernatant water from the precipitation tank was introduced. The microbubble generator was operated with a 15 day on, 15 day off cycle for 5 months to collect discharged water samples (4L) and measure TOC. As the supernatant water from the precipitation tank flowed into the separation membrane tank, about 95% of the supernatant water MLSS was removed so the MF fouling from biological contamination was prevented. Due to the application of microbubbles to supernatant water from the precipitation tank, the differential pressure of the separation membrane tank decreased by 1.6 to 2.3 times and the water flow increased by 1.4 times. Applying microbubbles increased the TOC removal rate by more than 58%. This study showed that separately operating the air tank and the separation membrane tank can reduce fouling, and suggested that applying additional microbubbles could improve the differential pressure, water flow, and fouling to provide a more efficient advanced treatment method.

• Journal of the Society of Disaster Information
• /
• v.19 no.2
• /
• pp.439-450
• /
• 2023

Purpose: When conducting fire inspections in Korea, there are objects that violate the fire protection regulations that require a straight line distance of more than 5m between the air inlet and the discharge section if the floor area is less than 400m2, and this paper analyzes the reasons and conducts a model experimental study to support the need for related fire protection regulations. Method: Domestic firefighting objects were investigated and confirmed, domestic and foreign papers, policies, and laws and regulations were examined, and spaces with a straight line distance of less than 5m and more than 5m between the air inlet and discharge section were selected and analyzed through model experiments in a living room of less than 400m² . Result: When examining the domestic fire protection regulations (NFPCNational Fire Perpormance Code), the separation distance between the air inlet and the outlet is more than 5m when the floor area is less than 400m² , but as a result of the actual investigation, it was confirmed that there are firefighting objects that cannot keep the separation distance. In addition, when a paper review of overseas fire protection regulations for a straight line distance of more than 5m showed that there was no regulation on the straight line distance between the air inlet and the discharge section, the model experiment showed that the discharge speed was better when the straight line distance between the air inlet and the discharge section was more than 5m than when it was less than 5m. Conclusions: In this study, when examining overseas fire laws and regulations by comparing the performance of the fire protection ratio for the straight line distance between the air inlet and the exhaust section, there is no mandatory regulation for the straight line distance, but the domestic fire protection regulations (NFPCNational Fire Perpormance Code) require more than 5m. It is hoped that this will be reflected in the design stage in the future, and a foundation will be laid to reduce the responsibility and burden of fire superintendents.

• Korean Journal of Heritage: History & Science
• /
• v.55 no.4
• /
• pp.196-209
• /
• 2022

This study compared and analyzed the spatial division function and role of partitions by comparing the entire space and the spatial changes before and after the installation of partitions in <Donggwoldo>, which was manufactured in the late Joseon Dynasty. As a research method, a set standard was prepared to decompose the space of <Donggwoldo> into a unit space, and the standard was set according to the role and height of the space by classifying it into a main space, sub space, and transition space. Two convex maps were prepared according to before and after the installation of the Panjang, and the values of connectivity, control, and integration, which are spatial syntax variables, were calculated and analyzed. The results of the study are as follows. First, the partition in <Donggwoldo(東闕圖)> did not affect the overall spatial arrangement and control or connection of Donggwol, but the movement and access of space is limited to specific areas. Second, the partition was a facility intensively distributed in Naejeon(內殿) and Donggung(東宮) to be used actively in the way of space utilization. It shows that the unit space increased rapidly due to the installation of the partition. Since the partition was installed in the spaces that were open and under high control in the case of Naejeon(內殿), it helped to secure private spaces as closed ones under low control. On the other hand, for Donggung(東宮), the spaces were compartmented and divided with the partition to guide the movement path through narrow gates of the partition and increase the depth of the space. This helped to create spaces that are free and can be hidden as it increased the number of spaces coming through. Third, In addition to the functions of "eye blocking, space division, and movement path control" revealed in prior research, the partition has created a "space that is easy to control" within a specific area. The installation of the partition reduced the scale through the separation of spaces, but it occurred the expansion of the movement path and space. Also, the partition functioned to strengthen hiding and closure or increase openness as well through space division. This study is significant in that it revealed the value of the spatial control function of panjang through the analysis of spatial control and depth by analyzing the function of the partition with a mathematical model in addition to the analysis and study of the function and role of panjang. In addition, it is valuable in that it has prepared a framework for analysis tools that can be applied to traditional residential complexes similar to palaces by applying space syntax to <Donggungdo> to create convex spaces according to unit space division and connection types of palace architecture and landscape elements.

• The Journal of Korean Society for Radiation Therapy
• /
• v.34
• /
• pp.7-12
• /
• 2022

Purpose: When it is difficult to secure the skin dose when treating Irregularly Shaped Skin Surface such as the nose where it is difficult to apply a bolus, increase the skin dose with a treatment plan that combines the IMRT (Intensity Modulated Radiation Therapy) delivery technique and FFF (Flattening Filter Free), It was tried to find out whether or not through the phantom experiment. Materials & Methods: Based on the 6MV-FF (Flattening Filter) and VMAT (Volumetric-Modulated Arc Therapy) treatment plans, which are the most commonly used treatment plans for head and neck cancer, A comparison group was created by combining VMAT and IMRT, FF and FFF, and the presence or absence of 5 mm bolus application. A virtual target was created on the Rando Phantom's nose, and a virtual bolus of 5 mm was applied assuming full contact on the Rando Phantom's nose. Five measurement points were determined based on the phantom's nose, and the absorbed dose was measured by irradiating each treatment plan 3 times per treatment plan according to the treatment technique and whether or not the bolus was applied. Result: The difference in skin dose in FF vs FFF increased in the case of FFF in VMAT bolus off, and there was no difference in case of IMRT bolus off. In VMAT bolus 5 mm and IMRT bolus 5 mm, it was confirmed that the skin dose was rather decreased in FFF. The difference in skin dose between VMAT and IMRT increased only in the case of FFF bolus off, and there was no statistical difference in the rest. For the difference in skin dose between bolus off vs bolus 5 mm, it was confirmed that the skin dose increased at bolus 5 mm, except for the case of using IMRT FFF. The treatment plan combining IMRT and FFF did not find any statistically significant difference as a result of analyzing the measured values of the treatment plan skin dose applied with a 5 mm bolus using the commonly used VMAT and FF. Therefore, it is thought that by using IMRT_FFF, it is possible to deliver a skin dose similar to that of applying a 5 mm bolus to VMAT_FF, which can be useful for patients who need a high skin dose but have difficulty applying a bolus. Conclusion: For patients who find it difficult to apply bolus, an increase in skin dose can be expected with a treatment plan that properly combines IMRT and FFF compared to VMAT and FF.

• Geophysics and Geophysical Exploration
• /
• v.25 no.4
• /
• pp.167-176
• /
• 2022

We designed a borehole deviation survey tool applicable for steel-cased holes, K-DEV, and developed a prototype for a depth of 500 m aiming to development of own equipment required to secure deep subsurface characterization technologies. K-DEV is equipped with sensors that provide digital output with verified high performance; moreover, it is also compatible with logging winch systems used in Korea. The K-DEV prototype has a nonmagnetic stainless steel housing with an outer diameter of 48.3 mm, which has been tested in the laboratory for water resistance up to 20 MPa and for durability by running into a 1-km deep borehole. We confirmed the operational stability and data repeatability of the prototype by constantly logging up and down to the depth of 600 m. A high-precision micro-electro-mechanical system (MEMS) gyroscope was used for the K-DEV prototype as the gyro sensor, which is crucial for azimuth determination in cased holes. Additionally, we devised an accurate trajectory survey algorithm by employing Unscented Kalman filtering and data fusion for optimization. The borehole test with K-DEV and a commercial logging tool produced sufficiently similar results. Furthermore, the issue of error accumulation due to drift over time of the MEMS gyro was successfully overcome by compensating with stationary measurements for the same attitude at the wellhead before and after logging, as demonstrated by the nearly identical result to the open hole. We believe that the methodology of K-DEV development and operational stability, as well as the data reliability of the prototype, were confirmed through these test applications.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.3
• /
• pp.21-29
• /
• 2023

In this study, the stress characteristics of temporary fixed steel rods were analyzed in the "temporary fixing system using internal prestressing tension", which is mainly applied to the construction of superstructures by FCM. It was difficult to confirm the changes in initial tensile force in this system because the steel rod was internally connected to the pier and the PSC BOX. Therefore, measurement was performed before and after the completion of each segment using an FBG sensor to measure the change in the micro length of the steel rod. The results of the analysis showed that 75% to 90% of the maximum vertical contraction of the steel rod that occurred until the completion of the cantilever segment occurred in the fixing ~ 1segment, and the maximum loss of initial prestressing force was 39%. Such excessive loss of tension force to 1 segment means that tension is needed to improve the precision of construction during the fixation, and re-tension is needed to secure stability for conduction of cantilever segments after the completion of 1segment. In the 2 ~ last segment, the stress of the steel rod decreased gradually, and in the summer, the decrease in stress tended to partially recover due to the increase in the length of the steel rod corresponding to the increase in the vertical volume of PSC BOX. The dominant factor in the stress change in 2~ last segment in this phenomenon is judged to be the change in the length of the steel rod according to the temperature. Unlike the change in length, the relaxation was 1.2-2.7%, which was mostly offset by the opposite stress corresponding to the temperature stress. Therefore, a plan was proposed to improve the internal stress, such as adjusting the fixation time.

• Journal of the Korean Orthopaedic Association
• /
• v.54 no.4
• /
• pp.309-316
• /
• 2019

Purpose: This study examined the residential environment and accessibility of rehabilitation for cerebral palsy (CP) to identify the problems with residential laws pertaining to the disabled and provide basic data on the health legislation for the rights of the disabled. Materials and Methods: The literature was searched using three keywords: residence, rehabilitation, and accessibility. Two items were selected: residential environment and rehabilitation accessibility. The questionnaire included 51 items; 24 were scored using a Likert scale and 27 were in the form of multiple-choice questions. Results: This study included 100 subjects, of which 93 lived at home and seven lived in a facility. Of these 93 subjects, 65% were living in apartments, usually two or more floors above ground, and 40% of them were living without elevators. According to the Gross Motor Function Classification System, subjects with I to III belonged to the ambulatory group and IV, V were in the non-ambulatory group. Subjects from both groups who lived at home found it most difficult to visit the rehabilitation center by themselves. In contrast, among those who lived at the facility, the ambulatory group found it most difficult to leave the facility alone, while the non-ambulatory group found it most difficult to use the toilet alone. Moreover, 83% of respondents thought that rehabilitation was necessary for CP. On the other hand, 33% are receiving rehabilitation services. Rehabilitation was performed for an average of 3.6 sessions per week, 39 minutes per session. Conclusion: There is no law that ensures secure and convenient access of CP to higher levels. Laws on access routes to enter rooms are insufficient. The disabled people's law and the disabled person's health law will be implemented in December 2017. It is necessary to enact laws that actually reflect the difficulties of people with disabilities. Based on the results of this study, an investigation of the housing and rehabilitation of patients with CP through a large-scale questionnaire will necessary.

• Korea Science and Art Forum
• /
• v.20
• /
• pp.455-464
• /
• 2015

As the recognition toward the Korean design education development to nurture creative talents for the future society has been expanded recently, various supports and promoting strategies are being suggested. This study suggests the orientalism-based new design education platform in design education field to nurture creative talents. To have the competitiveness of creative talent nurturing, the system and education programs to rear creative talents are required. The purpose of this study is to suggest the new platform for the change of direction in design education and search for the methods in detail. The research process can be described as following: First, this study stated about the research background and its boundary. Based on the literature review and the condition of the crisis of Korean design education (Korean Industrial Statistic Investigation), it described the current condition and the characteristics. Second, this study stated about the education which will be disappeared in the information society, the change of direction in design education, and the new platform. In the current study, the change toward the strategies that give priority to the growth strategies on the knowledge-based industry was stated. Third, this study stated about that the future design education should be centered on the orientalism-based creativity in the trend changing to the six conditions for the future talents and the beliefs and values toward Asia, and what methods should be sought to achieve this trend. It suggested focusing on the aim for the direction for College education and its program curriculums as the solutions in detail. Fourth, based on the contents stated earlier in this study, it stated synthetically the direction of practice through the network of the design cluster and derived the implications. In conclusion, based on the recent orientalism-based mind, this study suggested the ways to find the identity of Korean design education itself and have the competitiveness in design education programs. The ways to secure them is to come from the integrated system innovation of the network. By actively applying the design clusters, colleges and universities, designers, studios, government policy organizations, design institutes, corporates, media, and fairs, this study suggests the sustainable education system and the practical methods.

• Economic and Environmental Geology
• /
• v.56 no.3
• /
• pp.343-363
• /
• 2023

Sulawesi island, as a global producer of nickel resources, is leading the rapid growth of nickel industry of Indonesia. Nickel laterite deposits in Sulawesi was formed by lateritization of the world-scale East Sulawesi Ophiolite (ESO) under the active tectonic setting and tropical rainforest climate. In this paper, exploration cases for nickel laterite deposits in five regions of Sulawesi are reported. Regional characteristics on nickel laterite deposits in Sulawesi are understood based on various exploration activities such as outcrop, trench and pit survey, petrological observation, geochemical analysis, and interpretation of drilling data, etc.. In the northeastern part of 'Southeast-Arm', which is a strategic location for nickel industry of Indonesia, ESO is extensively exposed to the surface. In the Morombo and Morowali regions, typical high-grade saprolite-type orebodies with a thickness of 10 to 20 m occur. The cases showed that topographic relief tends to regulate Ni-grade distribution and orebody thickness, and that high grade intervals tend to occur in places where joints and garnierite veins are dense. In the Tinanggea and South Palangga regions in the southern part of the Southeast-Arm, overburden composed of Neogene to Quaternary deposits is a major factor affecting the preservation and profitability of nickel laterite deposits. Despite the overburden, high-grade saprolite-type orebodies composed of Ni-bearing serpentine with garnierite veins occur in a thickness of around 10 m to secure economic feasibility. In contrast, in the Ampana region in the northern part of 'East-Arm', low-grade nickel laterite deposits with immature laterite profile was identified, which is thought to be the result of active denudation due to tectonic uplift. Exploration cases in this paper will help to understand characteristics and controlling factors on nickel laterite deposits in Sulawesi, Indonesia.

• Journal of Christian Education in Korea
• /
• v.72
• /
• pp.245-271
• /
• 2022

The purpose of this study is to develop a nursing clinical practice education model that applies case-based learning and co-teaching to nursing students, and to secure the validity of the developed model. To verify the validity of the nursing clinical practice education model, it was applied to the subject of 'Health Response and Nursing VI (Perception/ Cognition) Practice' in the 2nd semester of 2021 at J University in Jeonju, and the instructor's response to the model was evaluated. Surveys and focus group interviews were conducted on confidence in clinical practice and teaching and learning models. After deriving the case-based learning stage and co-teaching elements through a review of precedent literature and case studies, an initial model was devised after expert review, and the devised model was reviewed for internal validity by nursing education experts, and then modified and supplemented. As a result of the learner response evaluation conducted after applying the model to the clinical practice subject for external validation verification, the confidence in clinical performance was 4.22 points and the satisfaction with the teaching-learning model was 4.68 points. Summarizing the results of the focus group interview, the importance of prior learning and the learning of selected cases based on actual cases, learning terminology and professional knowledge, eliminated fear of the practice field, felt familiar, and learned various cases. He said that he was able to think critically through the time to organize the knowledge learned in the practice field. In addition, through co-teaching, it was found that field leaders and advisors taught the theoretical and practical aspects at the same time through examples, thereby experiencing practical education closer to practice. It is expected that the nursing clinical practice education model developed through this study, applying case-based learning and co-teaching, will be an effective teaching and learning model that can reduce the gap between theory and practice and improve the clinical performance of nursing students.