• Architectural research
• /
• v.10 no.2
• /
• pp.37-42
• /
• 2008

This study is to get the proper evaluation of the residual property of reinforced concrete beam exposed to fire. This study focused on the strength resistance and analytical evaluation of RC members exposed high temperature. And this study is the basis analytical research to conduct the other studies. To analysis by the finite element method, the Total-RC program was used to analysis it and the Total-Temp program was also used to analysis the temperature distributions at the section. All of results were compared with the pre-existing experimental data of simple supported beam. Using it, the parameters influencing the structural capacity of the high temperature-damaged RC members and residual strength estimation are investigated. The temperature distribution and the structural capacity at the section are calculated in this step. An application of this method is compared with the heating test result and residual property test for simple supported beam which is subjected to ISO 834 test fire. The results of this study are as follows; 1) The loads-displacement relationship of RC beam, considering initial thermal stress of cross section and heat transfer analysis are estimated comparing analytical value with pre-existing experimental results. 2) by the heating time (0, 1, 2 hours), the results of analysis with parameters show that the load capacity exposing at fire is affected.

• International conference on construction engineering and project management
• /
• 2015.10a
• /
• pp.188-191
• /
• 2015

This study is based on the data of velocity actually measured at varied the heights in the last 3 years. As mentioned in the World Meteorological Monitoring Plan(World Weather Watch: WWW), using the meteorological data by radiosonde can calculate the probability of velocity greater than 10m/s which is the standard beginning point of non-working condition by wind. The height is divided into sections, with 100m for each section starting from the ocean surface up to 700m high. The data measured at each section could be used for estimating and predicting the probability of non-working days for the construction nearby. For example, the data of Osan region is expected to be applicable for the project located in Seoul which has similar geographical conditions. As comparing the velocity varied with height, non-working days calculated basing on the measured data shows a variation of from -0.3 to +64 days. However, this study use Weibull distribution which considered more reliable, the result is expected to be more useful, as the data was all actually measured in the real conditions.

• Journal of Biomedical Engineering Research
• /
• v.21 no.2
• /
• pp.189-201
• /
• 2000

Mechanical factors in the human body are considered to play a dominant role in low back problems. Various spinal structures. including muscles, act in unison to resist the external load. An estimation of the muscle forces in this structure requires a knowledge of the orientation, location and area of cross-section of the muscles to complete the formulation of a truly three-dimensional mathematical model of the spine. The geometric parameters which are calculated were the line of action, the centroid and physiologic area of cross-section of each muscle as a function of the spinal level. This geometric data were obtained from CT scans of 11 subjects participating in this study.

• Journal of the Korean Society of Safety
• /
• v.28 no.1
• /
• pp.57-62
• /
• 2013

Aerodynamic characteristics of cross section shape is an important parameter for the wind response and structural stability of long span bridges. Numerical simulation methods have been introduced to estimate the aerodynamic characteristics for more detailed flow analysis and cost saving in place of existing wind tunnel experiment. In this study, the computational fluid dynamics(CFD) simulation and large eddy simulation( LES) technique were used to estimate lift, drag and moment coefficients of four cross sections. The Strouhal numbers were also determined by the fast Fourier transform of time series of the lift coefficient. The values from simulations and references were in a good agreement with average difference of 16.7% in coefficients and 8.5% in the Strouhal numbers. The success of the simulations is expected to attribute to the practical use of numerical estimation in construction engineering and wind load analysis.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.3A
• /
• pp.229-239
• /
• 2010

For the purpose of improvement of the load carrying capacity and constructibility of the conventional steel-concrete composite girder through a effective appliance of the construction materials and optimization of the girder section, a new type section of composite girder and RC shear connection were proposed. In this study shear strength of the RC shear connection is estimated, and the characteristics of shear load-slip behaviour is analyzed. Push-out tests on shear specimens and FEM analysis with various design parameters are carried out, and results are analyzed. The results of test and FEM analysis showed that shear strength of RC shear connection is underestimated by the design provisions of the current design code. By regression analysis a empirical equation for the estimation of shear strength of RC shear connection is proposed.

• Journal of Ocean Engineering and Technology
• /
• v.30 no.6
• /
• pp.468-473
• /
• 2016

This paper focuses on the estimation of local ice loads exerted from ship-ice interaction processes. The Korean IBRV ARAON was used to perform field ice trials during her 2015 Arctic voyage. During ARAON's general ice transit, a total of 72 channels of data from both strain gauges on the inner hull plates and those installed on the transverse frames of the ARAON's bow section structures were analyzed to calculate the local ice loads. The local ice loads estimated from the analysis of the shear strain data measured on the side frames were compared to those from the hull plate pressures.

• Proceedings of the KSR Conference
• /
• 2003.10b
• /
• pp.563-568
• /
• 2003

High-speed railway bridges subject to effect of dynamic loads by interaction between vehicle load which run specially fast and behavior of bridges. Such dynamic load effects result in fluctuations and fatigues to each elements as well as whole conduct of bridges. and is influenced in life of bridges. For these reason. Analysis and estimation of data about dynamic behavior of bridges occupies important factor in that estimate the remaining life of bridges and select the maintenance. repair and retrofit. In this paper. Analysis for the dynamic behavior of bridges using displacement and acceleration data that is actuality measure data to the bridges of Seoul-Susan high speed railroad test section has been made.

• International Journal of Railway
• /
• v.6 no.2
• /
• pp.45-52
• /
• 2013

Railway construction needs vast soil investigation for its infrastructure foundation designs along the planned railway path to identify the design parameters for stability and serviceability checks. The soil investigation data are usually classified and grouped to decide design input parameters per each construction section and budget estimates. Deterministic design method which most civil engineer and practitioner are familiar with has a clear limitation in construction/maintenance budget control, and occasionally produced overdesigned or unsafe design problems. Instead of using a batch type analysis with predetermined input parameters, data population collected from site soil investigation and design load condition can be statistically estimated for the mean and variance to present the feature of data distribution and optimized with a best fitting probability function. Probabilistic approach using entire feature of design input data enables to predict the worst, best and most probable cases based on identified ranges of soil and load data, which will help railway designer select construction method to save the time and cost. This paper introduces two Monte Carlo simulations actually applied on estimation of retaining wall external stability and long term settlement of organic soil in soil investigation area for a recent high speed railway project.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2006.10a
• /
• pp.87-94
• /
• 2006

In this study we carried out to analyze the effect of wind load on the structural stability of a container crane according to the change of the boom shape using wind tunnel test and provided a container crane designer with data which can be used in a wind resistance design of a container crane assuming that a wind load at 75m/s wind velocity is applied on a container crane. Data acquisition conditions for this experiment were established in accordance with the similarity. The scale of a container crane dimension, wind velocity and time were chosen as 1/200, 1/13.3 and 1/15. And this experiment was implemented in an Eiffel type atmospheric boundary-layer wind tunnel with $11.52m^2$ cross-section area. Each directional drag and overturning moment coefficients were investigated and uplift forces at each supporting point due to the wind load were analyzed.

• International conference on construction engineering and project management
• /
• 2015.10a
• /
• pp.730-731
• /
• 2015

This study aims at giving the framework to estimate the environmental load at planning and schematic phase. With increasing awareness of environmental issues, the effort to reduce the environmental impacts caused by human activity has been increasingly enlarged. So far most of researches estimating CO₂ emissions have analyzed energy consumption based on BOQ (Bills of Quantity) acquired after detailed design. There is also lack of reliability in the estimated environmental impact using the basic unit of a facility at the planning stage, because it uses a limited specific section of historical data. Thus, this study is targeted at developing framework to assess reliable environmental loads based on information available at project early phases by making case-bases from historical design information on PSC Beam Bridge. Historical database is built on the basis of the LCA (Life Cycle Assessment) and in order to set input information for estimating model, the literature about information in an early project phase are reviewed. Using the information available in the planning and schematic design stage, the Framework is presented to estimate the environmental load in an early stage in the project. Developing an environmental load estimation model in accordance with the Framework presented in this study, it is expected that the environmental load in the initial project phase can be estimated more quickly and accurately.