• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.1
• /
• pp.33-40
• /
• 2010

In this research, the effects for surface Improvement of plasma ion implanted carbide endmill tools were observed by measuring cutting forces and tools wear affecting surface roughness in high speed cutting. From the 2nd ion mass analysis, the oxidation layer was found to be built up by sputtering. The residual gas contamination of oxygen was found to be contained impurities in nitrogen gas. The plasma implanted ion was found to be spreaded, especially the nitrogen was implanted up to 150nm depth as impressed voltage and ion implanting time. It is analyzed as bring surface improvement by spreading deeply forming oxidation on surface. The factors in Analysis of Variance(ANOVA) about mutuality cause reference of cutting force. The cutting force Fx is affected by the interaction of spindle rpm and federate, the cutting force Fy is influenced by spindle rpm and time injected ion, and cutting force Fz is affected by the interaction of impressed voltage and feedrate. Also, it was found that the cutting forces of implanted tools become lower and the surface roughness is improved by the effect of nitrogen according to the implantation.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.10
• /
• pp.45-51
• /
• 2010

Electrical discharge drilling (ED-drilling) is a widespread machining method used to bore small holes with a high aspect ratio. This paper presents additional methods by which ED-drilling can improve machining speed, tool wear, and machined surface quality. Firstly, for high machining speed, and low tool wear, a new-type electrode that was ground on one side or both sides of the cylindrical electrodes was suggested to expel debris. The debris which is generated during the machining process can cause sludge deposition and secondary discharge problems: major reasons to decrease machining speed. This new-type electrode also reduced tool wear that was due to the decrease of unstable discharge in a machining gap by helping to expel waste water and debris from the gap. Secondly, to improve the machined surface roughness, an electrolyzation process was included after drilling. This process made the machined surface smooth by means of an electrochemical reaction between an electrode and a workpiece. In this study, the machining speed, electrode wear, and surface roughness were improved by the newtype electrode and the electrolytic process.

• Composites Research
• /
• v.20 no.6
• /
• pp.8-14
• /
• 2007

Debonding failure characteristics of the composite skin-stiffener specimens were experimentally investigated. The influences of bonding methods, types of stiffener shape and various secondary bonding parameters were evaluated. Present test results combined with the previous test results[1] showed that the failure displacement of the skin-stiffener specimens well evaluates the skin-stiffener debonding failure strength of the composite stiffened panels. The specimens with an open type stiffener had lower bending stiffness and larger failure displacement than those with a closed type stiffener. Secondary bonding and co-curing with adhesive had better failure strength than co-curing without adhesive film. Secondary bonded specimens failed by adhesive failure and co-cured specimens failed by delamination failure. As the bondline thickness was thinner, the skin-stiffener specimens had higher failure strength. The fillets had no influence on failure strength of the specimens. The influence of the surface roughness was shown according to types of stiffener shape.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.8
• /
• pp.716-719
• /
• 2007

The effects of the evaporation rate of MgO films using an electron beam on the MgO properties and the discharge characteristics of a plasma display panel (PDP) were investigated and analyzed. MgO films were deposited with the various MgO evaporation rates. The MgO properties such as the crystal orientation, the surface roughness, and the film structure were inspected using XRD (X-ray diffraction), AFM (atomic force microscopy). From the experiments and Paschen law, the maximum value of the secondary electron emission coefficient $({\gamma})$ was obtained at the evaporation rate of $5{\AA}/sec$. The XRD results and cathode-luminescence (CL) spectra show the ${\gamma}$ values are correlated with F/F+ centers of the molecular structure of MgO films. The minimum firing voltage and the maximum luminous efficiency were obtained at an evaporation rate of $5{\AA}/sec$. In the MgO film deposited at $5{\AA}/sec$, the (200) orientation and F+ center were most intensive.

• Nuclear Engineering and Technology
• /
• v.55 no.9
• /
• pp.3121-3125
• /
• 2023

Neutron conversion detectors that use ¹⁰B-enriched boron carbide are feasible alternatives to ³He-based detectors. We prepared boron carbide films at micron-scale thickness using direct-current magnetron sputtering. The structural characteristics of natural B₄C films, including density, roughness, crystallization, and purity, were analyzed using grazing incidence X-ray reflectivity, X-ray diffraction, X-ray photoelectron spectroscopy, time-of-flight secondary ion mass spectrometry, and scanning electron microscopy. A beam profile test was conducted to verify the practicality of the ¹⁰B-enriched B₄C neutron conversion layer. A clear profile indicated the high quality of the neutron conversion of the boron carbide layer.

• Journal of Korea Water Resources Association
• /
• v.37 no.7
• /
• pp.527-540
• /
• 2004

In order to investigate characteristics of the primary flow and the secondary currents in the meandering channel, laboratory experiments were conducted in the meandering channel made up of alterative bends haying 120。 arc angle. Experiments were performed in two types of cross-sections, a rectangular cross-section and a curved cross-section which was made to adopt a beta probability function. Three-dimensional velocity fields were measured using a micro-ADV. As the result of experiments, in case of the rectangular cross-section, the primary flow occurred taking the shortest course, which is similar to the result of previous researches. In case of the curved cross-section, the primary flow was expected to occur along the thalweg. but it occurred almost along the shortest way. This is considered due to effects of bottom roughness and sinuosity Not only a main cell but also a secondary cell of secondary currents were clearly shown by mean of the stream function. The secondary current intensity has the maximum value near the apex of the second bend for cases of both rectangular and curved cross-sections. However, the value of the secondary current intensity for the curved section is slightly larger than that for the rectangular cross-section. Also, in case of the rectangular cross-section, the higher the ratio of width to depth is, the larger the secondary current intensity is.

• Journal of Korea Water Resources Association
• /
• v.31 no.3
• /
• pp.291-301
• /
• 1998

The objective of this study is to analyze the characteristics of flow and bed topography with changing bed material in a 180-degree, with constant-radius curved experimental channel. Sand($D_{50}$ = 0.56 mm, s = 2.65) and anthracite($D_{50}$ = 0.26 mm, s = 1.54) were selected as bed materials. The maximum scour depth was found to be about two times for the mean flow depth at the outer bank of bend angle $30^{\circ}~60^{\circ}$, and in case of anthracite, it was found upper part of bend angle $5^{\circ}~15^{\circ}$ than that of sand. Regardless of bed materials the path of maximum streamwise velocity is skewed inwards in the upper part of the bend, the maximum velocity shifts outwards, and it lagged downward as bed roughness increases. The maximum skewed angle of flow grows faster in the smooth bottom than in the rough one, and its value also increases. The secondary flow in anthracite bottom was measured larger than that of sand one, and two cells of secondary flow was found in this experiment.

• Journal of the Korean Society for Railway
• /
• v.5 no.1
• /
• pp.40-47
• /
• 2002

In this study, and analytical method for ride sensitivity analysis of a train with non-linear suspension elements are proposed. Non-linear characteristics of springs and dampers for primary and secondary suspensions of a train are parameterized using polynomial interpolation. Vertical dynamic model of a three-body train running on straight rail with the predetermined roughness expressed in terms of spectral density function is set up and its equations of motion for ride analysis are derived. Using the direct differentiation method, sensitivity equations of the vertical dynamic model with respect to design parameters associated with non-linearity of suspensions are obtained. Based on the sensitivity analysis, improvement of ride is achieved by varying appropriate suspension parameters.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1589-1595
• /
• 2000

레이저 텍스쳐와 미케니칼 텍스쳐 컴퓨터 하드디스크의 마찰과 마코 매카니즘이 Contact Start/Stop test 실행후의 특성들에 대해 연구되었다. 다양한 분석적이고 기계적인 테스트 기술들이 이용되었다. 형상, 조도, 화학적 조성, 기계적 성질, CSS 로부터 기인된 코팅의 마찰특성들에 대해 그 변화들을 조사하였다. 즉, AFM(Atomic Force Microscopy), Nano-Indentation, Nano-Scratch, TOF-SIMS(Time of Flight Secondary Ion Mass Spectroscopy), AES(Auger Electronic Spectroscopy)등이 이 연구에 적용되었다. 레이저 텍스쳐 범프의 표면조도와 미케니칼 텍스쳐 지역의 표면조도는 각각 대략적으로 4nm 와 7nm 감소되었다. 탄성계수와 경도값은 CSS test후에 증가하였고 가장 바깥쪽의 코팅층의 변형강화가 생겨났다. 자성층과 Ni-P 층 사이에 점착성의 문제가 확인되었다. TOF-SIMS 분석은 C 와 $C_2F_5$의 세기에 있어서 감소를 드러냈고 이것은 코팅 표면에 윤활제 요소의 마모를 확실시 할수 있는 결과로 나타났다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.496-498
• /
• 2005

We reported that high dielectric hafnium oxide nano-film deposited by thermal atomic layer deposition on the poly-silicon film (poly-Si). The poly -Si film was produced by plasma enhanced chemical vapor deposition and excimer laser annealing. We used the hafniu m chloride ($HfCl_4$) and water as the precursors and analyzed the hafnium oxide film by transmission electron microscope and secondary ion mass spectrometer. Hafnium oxide produced by the ALD method showed very good coverage on the rough surface of poly-Si film. While deposited with 200 cycles, these hafnium oxide films revealed a relatively smooth surface and good uniformity, but the cumulative roughness produced by the incomplete reaction was apparent when the amount of deposition cycle increased to 600 cycles.