• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.97-102
• /
• 2003

An experimental study is conducted to investigate the effects of duct corrugation angle on heat/mass transfer characteristics in wavy ducts by using a naphthalene sublimation technique. The corrugation angles of the wavy ducts are $145^{\circ}$ , $130^{\circ}$ and $115^{\circ}$ . and the Reynolds numbers based on the duct hydraulic diameter vary from 300 to 3,000. At the low $Re(Re{\leq}1000)$, high heat/mass transfer regions are formed by the secondary vortex flows called Taylor-Gortler vortices on both pressure-side and suction-side walls. At the high $Re(Re{\geq}1000)$, the effects of these secondary flows are vanished. As corrugation angle decreases, the local peak Sh induced by Taylor-Gertler vortices are increased and average Sh also enhanced. More pumping power (pressure loss) is required with the smaller corrugation angle due to the stronger secondary vortex flows.

• 대한토목학회논문집
• /
• 제30권2B호
• /
• pp.179-189
• /
• 2010

본 연구에서는 수치모의를 통하여 전단면 식생 수로에서 와도의 생성을 분석하였다. 지배방정식에서 난류 폐합을 위해 레이놀즈응력모형을 이용하였다. 거친 하상-매끄러운 측벽 및 매끄러운 하상-거친 측벽을 갖는 개수로 흐름을 수치모의하여 서로 다른 형태의 이차흐름 구조가 형성되는 것을 확인하였다. 즉, 거친 하상 조건에서는 자유수면 이차흐름의 규모가 감소되고, 거친 측벽 조건에서는 자유수면 이차흐름의 구조가 더 커지는 것으로 나타났다. 또한 전단면 식생 수로를 수치모의하여 수심 크기의 바닥 이차흐름이 형성되고, 식생 밀도가 증가함에 따라 자유수면 이차흐름이 점차 사라지는 것을 확인하였다. 또한 이차흐름 생성에 중요한 역할을 하는 난류의 비등방성 및 레이놀즈응력 분포를 식생밀도에 따라 살펴보았다. 한편, 와도 방정식을 분석한 결과, 비식생 수로의 경우 벽 및 수면 경계 근처에서는 난류 비등방성에 의한 생성항이, 경계와 떨어진 곳에서는 레이놀즈응력에 의한 생성항이 와도 생성에 중요한 역할을 하는 것으로 나타났다. 그러나 식생 수로에서는 이러한 특성이 사라지는 것으로 확인되었다. 또한 비식생 수로에서는 바닥과 수면에서의 와도 생성이 강하게 발생되지만, 식생 수로에서는 바닥과 식생 높이에서 와도 생성이 크게 발생되는 것으로 나타났다.

• 대한기계학회논문집B
• /
• 제20권9호
• /
• pp.2924-2932
• /
• 1996

As the environmental pollution can be greatly reduced and the waste heat can be also recovered through a combustion of municipal solid waste, the incineration begins to be highlighted recently in our country. But it is very difficult to be operated with constant combustion conditions for a long time as the domestic waste is composed of various components, contains a large percentage of water, and has a low heating value. Therefore, the cold flow test and partial hot flow test were conducted in the incinerator by use of injection angles of a secondary air affecting fluid flow as the first action to maintain the optimum combustion conditions. A model to a scale of 1:10 was designed and manufactured through the similarity of model and prototype flows. Velocities and temperatures were measured through the experiment. From the results, fluid flows of secondary air obtained from partial hot flow test correspond almost well with those of main flow obtained from cold flow test. Consequently, injection angles of secondary air are proved to affect main flow decisively.

• 대한기계학회논문집B
• /
• 제20권10호
• /
• pp.3251-3261
• /
• 1996

Flows were measured in an unshrouded centrifugal impeller. By using a single slanted hot-wire probe and a Kiel probe mounted on the impeller hub disk, the 3-D relative velocities and the rotary stagnation pressures were measured in seven circumferential planes between the inlet and outlet of the impeller rotating at 700 rpm, which diameter is 0.39 meter, and the static pressures and the slip factor at the impeller outlet were estimated from the measured values. Measurements were made for three flow rates corresponding to zero incidence and two others with the greater and the smaller one than zero. From the measured data in these flow rates, the followings were investigated in the impeller passage, the variation of the primary and secondary flows, the leakage flows, the wake's position and its size, the static pressure rise and the loss production mechanism. Furthermore the static pressure and the slip factor were compared with the results of inviscid Quasi-3D calculation.

• 대한기계학회논문집B
• /
• 제22권1호
• /
• pp.12-24
• /
• 1998

The paper presents the mechanism of secondary flows and the associated total pressure losses occurring in turbine cascades with turning angle of about 127 and 77 degree. Velocity and pressure measurements are taken in seven traverse planes through the cascade passage using a prism type five hole probe. Oil-film flow visualization is also conducted on blade and endwall surfaces. The characteristics of the limiting streamlines show that the three dimensional separation is an important flow feature of endwall and blade surfaces. The larger turning results in much stronger contribution of the secondary flows to the loss developing mechanism. A large part of the endwall loss region at downstream pressure side is found to be very thin when compared to that of the cascade inlet and suction side endwall. Evolution of overall loss starts quite early within the cascade and the rate of the loss growth is much larger in the blade of large turning angle than in the blade of small turning angle.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2002년도 유체기계 연구개발 발표회 논문집
• /
• pp.137-146
• /
• 2002

This paper presents a quasi-3-dimensional calculation method considering secondary flows in the impellers of diagonal flow blowers. A Quantitative estimation of the secondary flow effects is made by using secondary flow theories. In order to verify the validity of the adopted models, that is, span-wise mixing model and the tip clearance model, numerical simulations are performed for two different types of impellers of diagonal flow blowers which are designed differently. Numerical experiments are conducted for each of a constant tangential velocity type impeller, and a free vortex type impeller, both at two different flow coefficients. According to the simulation results, it was found that the present model considering span-wise mixing and tip clearance effect shows better agreements with the experimental data than those without these models in terms of the flow velocity and the angle distribution.

• 대한토목학회논문집
• /
• 제26권6B호
• /
• pp.573-581
• /
• 2006

본 연구에서는 레이놀즈응력모형을 이용하여 매끄러운 하상-거친 하상의 횡방향 연속구조를 갖는 개수로 흐름을 수치모의하였다. 개발된 모형을 이용하여 평균유속 및 난류량을 계산하고 기존의 실험결과와 비교하였다. 그 결과 레이놀즈응력모형이 매끄러운 하상-거친 하상의 횡방향 연속구조를 갖는 개수로 흐름에서의 평균유속과 난류구조를 비교적 유사하게 예측하는 것으로 나타났다. 특히 이차흐름 벡터도를 계산한 결과 매끄러운 하상에서는 상향류가, 거친 하상에서는 하향류가 나타나는 격자형 이차흐름이 발생하였으며, 이와 같은 격자형 이차흐름은 평균유속 및 난류량 분포에 큰 영향을 미치는 것을 확인하였다. 또한 와도 방정식의 각 항을 비교하여 개수로 흐름에서의 이차흐름의 성인(成因)을 분석하였다.

• 한국전산유체공학회지
• /
• 제20권1호
• /
• pp.32-38
• /
• 2015

A 3-dimensional compressible turbulent boundary layer solver has been developed. A time marching method is used to integrate the turbulent boundary layer equations. While the direct integration of the boundary layer equations is performed for unseparated flow regions, the inverse integration is performed for separated flow regions. The program is verified for flows that have analytical solutions or other numerical results. The solver will be merged with an Euler solver for viscous-inviscid interaction.

• 대한기계학회논문집B
• /
• 제28권4호
• /
• pp.441-448
• /
• 2004

A numerical study was conducted to show the effect of aspect ratio on the analogy of the developing laminar flows between in orthogonally rotating straight duct and in a stationary curved duct of rectangular cross-section. In order. to clarify the similarity of two nows, dimensionless parameters (equation omitted) and Rossby Ro= $w_{m}$$\Omega$ $d_{h}$, in a rotating straight duct were used as a set corresponding to Dean number, (equation omitted), and curvature ratio, λ=R/ $d_{h}$, in a stationary curved duct. Four. different aspect ratios A=0.25, 0.5, 2 and 4 were considered. Under the condition that the magnitudes of Ro and λ were large enough to satisfy the 'asymptotic invariance property' and the aspect ratio was larger than 1, there were strong quantitative similarities between the two flows such as flow patterns, friction factors, and maximum axial velocity magnitudes fur the same values of $K_{LR}$ and $K_{LC}$ . On the other hand, as the aspect ratio decreased below 1 (A=0.25 and 0.5), the difference of the secondary flow intensity between these two flows was enhanced and therefore the analogy of two flows was not so evident as that of the larger aspect ratio (A=2 and 4). 4).nd 4).

• 대한기계학회논문집B
• /
• 제22권2호
• /
• pp.139-152
• /
• 1998

In the present study, the flow characteristics of developing laminar oscillatory flows in a square -sectional 180 deg. curved duct are investigated experimentally. The experimental study using air in a square-sectional 180 deg. curved duct is carried out to measure velocity distributions with a data acquisition and LDV (Laser Doppler Velocimetry) processing system. In this system, Rotating Machinery Resolver (RMR) and PHASE program are used to obtain the results of unsteady flows. The major flow characteristics of developing oscillatory flows are found by analyzing velocity curves, mean velocity profiles, time-averaged velocity distribution of secondary flow, wall shear stress distributions, and entrance lengths. In a lower dimensionless angular frequency, the axial velocity distribution of laminar oscillatory flow in a curved duct shows a convex shape in a central part and axial symmetry. The maximum value of wall shear stress in a lower dimensionless angular frequency is located in an outside wall, but according to increasing the dimensionless angular frequency, the maximum of wall shear stress is moved to inner wall. The entrance lengths of laminar oscillatory flows in a square-sectional 180 deg. curved duct is obtained to 90 deg. of bended angle of duct in this experimental conditions.