• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 추계학술대회 논문집
• /
• pp.407-408
• /
• 2007

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.857-858
• /
• 2010

• Tribology and Lubricants
• /
• 제35권3호
• /
• pp.183-189
• /
• 2019

The driver seat of an automobile is in direct contact with the driver and provides the driver with a safe and comfortable ride. The seat consists of a frame, a rail, and many recliners. In recent years, strength and operating force measurement testing of the recliner have become vital for designing car seats. However, performance evaluation requires expensive testing equipment, numerous seat products, and considerable time. Therefore, the trend is to reduce experimentation through interpretation. This study examines the lubrication of solid lubricant for automotive seat recliners and confirms the friction and wear performance. In this study, the lubrication behavior of solid lubricants for car seat recliners is investigated to ascertain the friction and wear performance and to provide accurate values for the strength analysis. The friction material consists of a pin and a plate made from steel, which is widely used in recliners. The friction and wear under lubrication conditions are measured by a reciprocating friction wear tester. The friction coefficient is obtained according to the load and speed. Based on the obtained results, it is possible to achieve a reduction in the error of the test value and the analysis by providing the friction coefficient and wear of the lubricant. The results can be applied to the analysis of automobile seat design.

• 한국자동차공학회논문집
• /
• 제15권4호
• /
• pp.101-107
• /
• 2007

This study investigated the wear of the valve and seat insert seating faces. A tester, an exhaust valve and a seat insert were used. Test variables were cycle numbers ($2{\times}10^6,\;4{\times}10^6,\;6{\times}10^6\;and\;8{\times}10^6$) and Hz (10Hz and 25Hz). The other test conditions such as temperature ($350^{\circ}C$), fuel (LPG) and load (1960N) were fixed. The 10Hz tests indicated that the average Rmax of the valve increased at the rate of $7.76{\mu}m/10^6$ cycles starting from $29.42{\mu}m$ at the $2{\times}10^6$ cycles and that of the seat insert increased at the rate of $8.57{\mu}m/10^6$ cycles starting from $34.19{\mu}m$ at the $2{\times}10^6$ cycles. The 25Hz tests indicated that the average Rmax of the valve increased at the rate of $1.58{\mu}m/10^6$ cycles starting from $74.2{\mu}m$ at the $2{\times}10^6$ cycles and that of the seat insert increased at the rate of $1.25{\mu}m/10^6$ cycles starting from $83.95{\mu}m$ at the $2{\times}10^6$ cycles. The tribochemical reaction product covered the two seating faces, preventing the wear of the seating faces. As cycle numbers became greater, the average Rmax of the seating faces became greater, but the increase rate varied significantly depending on the Hz. The wear mechanism of the two faces was investigated through the tribochemical reaction.

• 한국정밀공학회지
• /
• 제26권3호
• /
• pp.88-97
• /
• 2009

The vacuum die casting techniques can diminish the porosity of products and provide better surface appearance by the ordinary high pressure die casting process. The vacuum system can also reduce the cold laps in the die casting process and minimize the overflow pockets of the die. The vacuum system does not need high pressures to die cast compared to the ordinary die casting process, and so enables die casting of large parts for a given machine size. Parts made by the vacuum system have higher strength and more elongation than parts made by the ordinary die casting systems. In this paper, we designed and produced the Magnesium seat frames using the vacuum die casting processes. The new Magnesium seat frame was designed to satisfy safety regulations. Some safety test procedures of the seat frame were simulated by the finite element method. We obtained 10% weight reduction by design modification of seat frames compared to the current model. Flow simulations were carried out to minimize the trial and error in producing the parts. The die casted parts using vacuum systems resulted in better mechanical characteristics and no defects compared to those without vacuum systems.

• 한국기계가공학회지
• /
• 제16권3호
• /
• pp.24-29
• /
• 2017

In this study, a seat cross member was fabricated by optimizing the resin transfer molding processing of CFRP (Carbon Fiber Reinforced Plastics) materials. This seat cross member is used in automotive underbody parts and provides side impact support. The seat cross was manufactured via vacuum resin transfer molding. The process included 1min of resin injection, 8 mins of heating, and 1 min of cooling, for a total molding time of 10mins. Tensile test results showed an average breaking load of 21.50kN, a tensile strength of 404 MPa, and an elastic modulus of 46.2 GPa. As a result, the CFRP seat cross provides the same strength as a similar steel part, but weighs 42% less.

• 한국자동차공학회논문집
• /
• 제12권4호
• /
• pp.50-57
• /
• 2004

Structural analysis and fatigue tests have been performed to develop design and evaluation technologies of automotive seat frames. Under the back moment loading condition, the numerical simulation unveiled the maximum stress up to the yield strength at the side frame bracket. To measure the stresses under the test condition, strain gauges were attached to some weakest points of the side frames. the measured strains are in good agreements with the CAE results. On the other hand, some fatigue tests have been performed using the side frame bracket specimens made of various welding types to evaluate their durabilities. From the fatigue tests and the numerical analyses, it was recommended that the bracket welding position should be moved upward.

• EDISON SW 활용 경진대회 논문집
• /
• 제5회(2016년)
• /
• pp.256-261
• /
• 2016

In this paper, Shape optimal design for a chair with 4 legs and 2 stretchers consisting of stainless steel was conducted. The shape was transformed by identifying stress and deformation for the part of leg and stretcher. In addition, load condition and mesh was designed using Hypermesh. The stress analysis was carried out using CSD_Elast that is one of EDISON program. In seat test, Maximum equivalent stress was showed at the contact part between seat and legs. As a result, a leg cross-section with rectangular and arch was designed. And optimal height of stretcher was found to reduce a deformation. Also, maximum deformation was reduced by designing a stretcher with ellipse cross-section. So, Optimal chair having 4 legs with rectangular cross section and 2 stretchers with ellipse cross section was shown to satisfy the safety ratio.

• 동력기계공학회지
• /
• 제15권5호
• /
• pp.67-71
• /
• 2011

Fine blanking is a specialized form of blanking where there is no fracture zone when shearing. This is achieved by compressing the whole part and then an upper and lower punch extract the blank. This allows the process to hold very tight tolerances, and perhaps eliminate secondary operations. In the present study, tensile test and numerical simulation has been performed to investigate distribution of deformation and stress of car seat recliner. The commercial ABAQUS/Explicit software was applied for analyzing the stress and strain of the recliner. In analysis, three lock gear has reached the maximum moment on rotational degree of 2.27. This is more than two times than maximum moment of same size recliner, and can be used safely. Therefore, these can use as criterion of actual structural design.

• 한국산학기술학회논문지
• /
• 제13권11호
• /
• pp.4956-4962
• /
• 2012

자동차의 다양한 부품 중 자동차 시트는 인간과의 직접 접촉 부위로서 승차감을 평가 할 수 있는 가장 기본적인 항목이다. 따라서 자동차 시트는 승차감과 동시에 충분한 강성과 강도를 가져야 할 것이다. 본 연구에서는 자동차 시트에서의 시트 쿠션 프레임과 백 프레임을 3D 모델링하였고, 쿠션 프레임의 비틀림 강도, 수직하중강도 시험, 백 프레임의 강도 시험 3가지 실험에 대해서 시뮬레이션으로 구조해석을 하였다. 해석결과, 쿠션 프레임 비틀림 강도 시험에서는 초기 전변형량의 최대값은 5.8421mm가 나왔고, 영구 전변형량의 최대값은 0.02539mm가 나왔다. 쿠션 프레임 수직하중강도 시험에서는 쿠션 프레임 앞쪽 끝단의 전변형량은 2.1159mm이고, 뒤쪽 끝단은 0.0606mm이다. 하중을 더 증가한 경우는 전변형량의 최대값은 3.1739mm가 나왔다. 3 가지의 백 프레임 강도 시험에서는 최대의 전변형량은 0.18634mm로 나타났다. 본 연구결과는 자동차 시트 쿠션 프레임 및 백프레임의 과도한 변형 및 파괴가 없음으로서 승객의 안전을 보장하는 충분한 강성과 강도를 검증할 수 있었다.