• Journal of the Korean Wood Science and Technology
• /
• 제51권6호
• /
• pp.493-508
• /
• 2023

Round timber materials of 600 mm length, cut from large-cross-section round timber of red pine (Pinus densiflora S. et Z.) of 450 mm width and 4.2 m length, were prepared as the target of kiln drying in this study. After treating the target materials through end sealing (ES), end sealing - kerfing (ES-K), lateral sealing - end sealing - boring (LS-ES-B), or lateral sealing - partial end sealing (LS-PES), the effects of the treatment on the incidence of drying defects were determined. The target materials with exposed lateral surface and sealed cross surface were steamed at the initial temperature of 65℃ above the official pest control temperature of 56℃, followed by kiln drying toward the final temperature of 75℃. The target materials with sealed lateral surfaces, on the other hand, were dried at the initial temperature of 90℃ at almost the maximum temperature of conventional kiln drying, as there is no risk of early check formation caused by surface moisture evaporation. The final temperature was set at approximately 100℃. The drying time, taken for the target materials with initial moisture content of 70%-80% to reach the target moisture content of 19%, varied across treatment conditions. The measured drying time was 1,146 hours (approximately 48 days) for the timber with sealed cross surface and 745 hours (approximately 31 days) for the timber with sealed lateral surface, until the moisture content reached the target level. The formation of surface checks could not be prevented in the control and ES groups, but a definite preventive effect was obtained for the LS-ES-B and LS-PES groups.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2000년도 추계학술발표회 초록집
• /
• pp.20-21
• /
• 2000

• 한국초지조사료학회지
• /
• 제5권2호
• /
• pp.116-120
• /
• 1985

Roll bale silage조제시(調製時) 밀봉지연(密封遲延)이 silage 품질(品質)과 소화율(消化率)에 미치는 영양(影響)에 대한 본(本) 시험(試驗)에서의 결과(結果)는 다음과 같다. 1. Roll bale silage의 내부온도(內部溫度)는 대조구(對照區)에서 $26{\sim}28^{\circ}C$였으나, 밀봉지연구(密封遲延區)에서는 밀봉(密封)을 늦게 함에 따라 열(熱)이 발생(發生)하여 roll bale내(內)의 온도(溫度)가 $55^{\circ}C$까지 상승하였다. 2. 밀봉지연구(密封遲延區)에서 유산함량(乳酸含量)은 현저하게 감소하였으며, $NH_3-N/T-N$함량(含量)은 증가하는 경향을 보였다. 일반성분(一般成分)에서는 밀봉지연구(密封遲延區)의 ADIN/T-N, 섬유질(纖維質) 및 lignin함량(含量)이 증가하였다. 3 . 단백질소화율(蛋白質消化率)에서는 밀봉지연구(密封遲延區)가 대조구(對照區)보다 낮았으나, 섬유질소화율(纖維質消化率)에서는 대조구(對照區)보다 높았다. 4. 제(第)1위내(胃內) pH는 밀봉지연구(密封遲延區)가 낮았으며, $NH_3-N$농도(濃度)에서는 별댜른 차이가 없었다. 총(總)VFA 농도(濃度)에서는 밀봉지연구(密封遲延區)가 낮았으나 총(總)VFA 함량중(含量中) 초산(酢酸)비율은 밀봉지연구(密封遲延區)가 높았다.

• 마이크로전자및패키징학회지
• /
• 제8권4호
• /
• pp.11-15
• /
• 2001

본 연구에서는 RF-MEMS소자의 웨이퍼레벨 패키징에 적용하기 위한 밀봉 실장 방법에 대하여 연구를 하였다. 비전도성 B-stage에폭시를 사용하여 밀봉 실장하는 방법은 플립칩 접합 방법과 함께 MEMS 소자 패키징에 많은 장점을 줄 것이다. 특히 소자의 동작뿐만 아니라 기생성분의 양을 줄여야 하는 RF-MEMS 소자에는 더욱더 많은 장전을 보여준다. 비전도성 B-stage 에폭시는 2차 경화가 가능한 것으로 우수한 밀봉 실장 특성을 보였다. 패키징시 상부기관으로 사용되는 유리기판 위에 500 $\mu\textrm{m}$의 밀봉선을 스크린 프린팅 방식으로 패턴닝을 한 후에 $90^{\circ}C$와 $170^{\circ}C$에서 열처리를 하였다. 2차 경화 후 패턴닝된 모양이 패키징 공정이 끝날 때까지 계속 유지가 되었다. 패턴닝 후 에폭시 놀이가 4인치 웨이퍼에서 $\pm$0.6$\mu\textrm{m}$의 균일성을 얻었으며, 접합강토는 20 MPa을 얻었다. 또한 밀봉실장 특성을 나타내는 leak rate는 $10^{-7}$ cc/sec를 얻었다.

• 한국유체기계학회 논문집
• /
• 제16권3호
• /
• pp.39-47
• /
• 2013

Effect of semicircular rib or groove on the performance of a rim-seal was evaluated using three-dimensional Reynolds-averaged Navier-Stokes equations. The turbulence was modeled using the one-equation Spalart-Allmaras turbulence closure model. Reynolds number based on the axial chord of the turbine blade was 500,000 at the mainstream outlet. The numerical results for a sealing effectiveness was validated in comparison with experimental data. To examine the effect of the semicircular rib or groove on sealing effectiveness of the rim-seal, location and diameter of the rib or groove were selected as the parameters to be performed. The rim-seals with the semicircular groove showed a higher sealing effectiveness than that with the semicircular rib. The semicircular groove installed on the stator side showed best sealing effectiveness among the numerical simulation results.

• 한국정밀공학회지
• /
• 제26권2호
• /
• pp.86-93
• /
• 2009

Elastomeric O-rings have been the most common seals due to their excellent sealing capacity, and availability in costs and sizes. One of the critical applications of O-ring seals is solid rocket motor joint seal where the operating hot gas must be sealed during the combustion. This has long been a design issue to avoid the system failure. For laterally constrained, squeezed and pressurized condition, deformed shape of O-ring was measured by computed tomography method and CCD laser sensor, compared with numerical calculations. As clearance gap changes, sealing performance had been evaluated on peak contact stresses at top, bottom and side contact surfaces. As clearance gap increases, peak contact stresses and contact widths in top and side contact surfaces increase, and the asymmetry of stress distributions is promoted due to pressure increase. It is suggested that peak stress of bottom contact surface can be approximated by simple superposition of peak ones due to squeeze and pressure. Under pressurized condition, sealing performance is dependent on not peak stresses of bottom and side contact surfaces but that of top.

• 한국기계가공학회지
• /
• 제14권1호
• /
• pp.21-28
• /
• 2015

A Tsunami damper, which is installed on the outer wall of a nuclear power plant, is usually used as a ventilation window of the machine room, but can serve as a device for preventing flooding of the machine room when large waves flow over the outer wall. The sealing strip, which is inserted between the casing and the blades, plays an important role in maintaining a watertight environment. In this study, in order to ensure an effective watertight performance of the tsunami damper, FE analysis is conducted to compare the contact characteristics of sealing strips with three different section shapes. In the analysis, the casing and the blade of Tsunami damper are assumed to be rigid bodies; the sealing strip is assumed to be a flexible body. The stress, the strain, and the contact pressure are investigated to examine the sealing performance of each model.

• 한국세라믹학회지
• /
• 제56권2호
• /
• pp.173-177
• /
• 2019

Thermal properties of a SiO₂-B₂O₃-BaO ternary glass system depending on compositional change of BaO have been examined to find a proper sealing material for reversible oxide cells. Glass transition temperature and thermal expansion coefficients increased simultaneously up to 55 mol% of BaO content. The structural role of BaO with regard to the thermal properties has been discussed on the basis of Raman spectroscopy results. Flowability of the glass at sealing temperature has been examined with packed glass powders of 12 mm diameter along with a high temperature optical microscope. The practical sealing property of the glass was also examined with YSZ coated with NiO-yittria stabilized zirconia (NiO-YSZ) and it showed good adhesion without noticeable reaction with NiO-YSZ layer.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.610-614
• /
• 1996

Sealing of lubricat-air mixture in the high performance machining conte is one of most the important characteristics to carry out enhanced lubrication. High speed spindle requires non-contact type of sealing mechanism. Evaluating an optimum seal design to minimize leakage is concerned in the aspect of flow control. Effect of geometry and leakage path are evaluated according to variation of sealing geometry, Velocity, pressure, turbulence intensity of profile is calculated to fina more efficient geometry and variables. This offers a methodological way of enhancement seal design for high speed spindle. The working fluid is regarded as two phases that are mixed flow of oil phase and air phase. It is more reasonable to simulate an oil jet or oil mist type high speed spindle lubrication. Turbulence and compressible flow model are used to evaluate a flow characteristic, This paper arranges a geometry of mostly used non-contact type seal and analyzes leakage characteristics to minimize a leakage on the same sealing area.

• Journal of Welding and Joining
• /
• 제33권1호
• /
• pp.49-53
• /
• 2015

An experimental study was conducted to investigate the effect of carbon nanotubes on the zinc corrosion resistance of sealing layer formed on the Tungsten Carbide spray coating. Using the nanotubes, a sealing agent in the form of solid-liquid suspensions was made and applied to the surface of spray coating. A series of experiments, consisted of three stages such as preparation of test piece, molten-pot immersion test, and evaluation of micro structure, were undertaken to demonstrate complicated interaction existing between zinc ions and sealing layer containing the nanotubes. Experimental results showed newly developed sealing layer were less susceptible to corrosion and thus coated layer was well protected even in the case of 10 days exposure. Comparison of the micro structure after molten pot test also indicated that carbon nanotubes still remained in the matrix and organized more reliable frame work constituted with boron nitride and chromium compound. It was revealed that carbon nanotubes in the sealing layer played positive role to enhance zinc corrosion resistance in the perspective of both fibrous structure and inherent chemical stability.