• Tribology and Lubricants
• /
• v.26 no.1
• /
• pp.61-67
• /
• 2010

The purpose of this paper is to study and analyze the failure examples on tribological characteristics of an automotive steering system. In this failure study, the grease leakage may stick leaked grease, dust, and wear particles between pinion and rack gears in mechanical steering system. In the case of seal failures such as a rod seal, o-ring and oil seals, the gear box and oil pump do not operate properly due to lack of oils. This means that oil pump does not supply a working fluid and produce a normal oil pressure of the steering system. This leads to leak a working fluid from the seals and produce a wear between pinion and rack gears. Especially, the leaked oil is usually mixed with internal wear particles and foreign dust/fine sands. Thus no leakage of working oils is very important design concepts, which is strongly related to the sealing components and smoothly operating of the mechanical friction parts of power steering system.

• Tribology and Lubricants
• /
• v.25 no.4
• /
• pp.225-230
• /
• 2009

Seals are very useful machine components in protection of leakage of lubricant or working fluid, and incoming of debris from outside. Various elastomer are widely used as sealing materials and the shaft surfaces are generally coated with high hardness material after heat treatment. It is generally known that the foreign debris and wear particles get stuck into sealing surface, the steel shaft surface can be damaged and worn by mainly abrasive wear. In this paper, using MARC, contact analysis are conducted to show the hard coated steel shaft surface can be fatigue failed by very small elastic particle intervened between seal and steel surface. Variations of contact and von-Mises stress distributions and contact half-widths with interference and coating thickness are presented. The maximum von-Mises stress occurs always in the coating layer or between coated layer/substrate interface. Therefore the coated sealing surface can be fatigued and then failed by very small particles. The results can be used in design of sealing surface and further studies are required.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.114-117
• /
• 2004

The purpose of this study is to investigate geometric effect on the contact stress at a lip seal. The geometries of interest were angle, thickness of lip seal and width of contact surface. The contact stress was calculated by using a coupled thermo-mechanical analysis method. The friction thermal load between lip seal and sleeve was adopted to design load. Based on the FEA results, design variables for controlling the maximum contact stress at the lip seal were identified.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1807-1810
• /
• 2003

The formed tool is used to machine the unique shape of rubber seal for geometrical shaping and reduction of cutting time. The bearing rubber seal produced by hot press forming has complex geometry for the complex geometrical shape to prevent leakage of lubricant oil and influx of the dust effectively. Because it is difficult to machine the unique shape exactly by the conventional tool, the formed tool is used in machining mold of the seal. In this paper, It is performed for selection of the formed tool to investigate cutting edge wear, cutting force, and surface quality. Also, an efficient high precision machining is proposed on the experiment data.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.51 no.10
• /
• pp.477-482
• /
• 2002

One of the key technologic requirements for rotary blood pumps is the sealing of the motor shaft. A mechanical seal, a journal bearing, magnetic coupling, and magnetic suspension have been developed, but they have drawbacks such as wear, thrombus formation, and power consumption. A magnetic fluid seal is durable, simple, and non power consumptive. Long-term experiments confirmed these advantages. The seal body was composed of a Nd-Fe-B magnet and two pole pieces; the seal was formed by injecting magnetic fluid into the gap (50${\mu}m$) between the pole pieces and the motor shaft. To contain the ferro-fluid in the seal and to minimize the possibility of magnetic fluid making contact with blood, a shield with a small cavity was attached to the pole piece. While submerged in blood, the sealing pressure of the seal was measured and found to be 31kPa with magnetic fluid LS-40 (saturated magnetization, 24.3 KA/m) at a motor speed of 10,000 rpm and 53kPa under static conditions(0mmHg). The specially designed magnetic fluid seal for keeping liquids out is useful for axial flow blood pumps. The magnetic fluid seal was incorporated into an intra-cardiac axial flow blood pump.

• Tribology and Lubricants
• /
• v.21 no.5
• /
• pp.227-235
• /
• 2005

This paper presents a tribological study on the failure cases of automatic transmission components in a passenger car. The automatic transmission system is composed of torque converter, clutch, brake, planetary gear, and valve body controlling oil pressure of an automatic transmission fluid. The most largest influence components in an automatic transmission are a torque converter and clutch plate in which are influenced by a wear and torque converting energy loss. The failure case study of an automatic transmission indicates that the tribological design and maintenance technologies should be considered as a key design concept. This means that the failure and power energy loss come from the friction, wear and a oil leakage of an automatic transmission, which is related to the oil seal and O-ring seal failures.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.5
• /
• pp.95-100
• /
• 2013

The important design factors for designing solid lubricating of dynamic seal are tightness, wear resistance and lubricant films. In this study, the effect factors influenced solid lubricating properties of the graphite were analyzed and wear behaviour caused for various test conditions was compared with results obtained from reciprocating wear tests. Also the optimal conditions for formation of lubricant films were investigate to evaluate wear properties of graphite materials. The repeated procedure for the formation of wear particles and lubricant films, and the dissipation of lubricant films was estimated the wear mechanisms with changes of wear depth. Therefore the lubricant film of graphite seal was generated by adhesion of wear particles on the worn surface and it was very useful in wear characteristics.

• The Journal of Korean Academy of Prosthodontics
• /
• v.22 no.1
• /
• pp.23-32
• /
• 1984

The effects between preexisting four types and one that author had designed of posterior palatal seal on the retention of denture base were compared and observed from six systemically healthy edentulous subjects. Using one without posterior palatal seal as the control, the retention of each type was measured and analyzed six times with cantilever type Load cell after adaptation of denture base, which were constructed with usual manner. The following results wear obtained. 1. Morphological and positional changes of posterior palatal seal effected on denture retention. 2. No specific type showed most desirable effect in every experimental subject. 3. Experimental subject I, II, VI showed higher retention on the control in every type. 4. In five types of posterior palatal seal, for subject III, VI F types and for subject II, V C types were most effective. 5. In each experimental subject F type showed higher retention than the control.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.11
• /
• pp.85-91
• /
• 2009

A lip seal is widely used not only to prevent leakage of fluids from an actuator or a rotating shaft but also to exclude outside substances. Recently, TPU(Thermoplastic Polyurethane), which is one of the sealing materials, has been frequently used due to its excellent mechanical properties and wear resistance. The material constants for finite element analysis through the experiment on stress relaxation are presented. The reaction forces of a shaft as well as the contact pressures of a lip seal under condition before and after stress relaxation using finite element analysis were obtained, The results show that stress relaxation has not a little effect on the performance of a lip seal.

• Journal of the Korean Society of Safety
• /
• v.27 no.3
• /
• pp.20-27
• /
• 2012

Mechanical seals are one of main components of high speed centrifugal pumps. So, it is very important to detect the faults (scratch, notch, indentation, wear) of mechanical seals since the damage of seal can cause a critical failures or accidents of machinery system. In the past, many researchers mainly performed to detect the seal fault using the time signals measured from sensors. Recently, studies are focused on the development of on-line real time monitoring system. But study on the feature parameters used for fault detection of mechanical seals has a little been performed. In this paper, we showed feature parameters extracted from accelerated and acoustic signals by using the discrete wavelet transform (DWT), alpha coefficient, statistical parameters. And also verified the possibility for fault detection of mechanical seal.