• International Journal of Naval Architecture and Ocean Engineering
• /
• v.2 no.4
• /
• pp.211-216
• /
• 2010

Recently a Wide Chord Tip (WCT) propeller has been developed and applied to a commercial ship by STX Offshore & Shipbuilding. It is reported that the WCT propeller significantly reduces pressure fluctuations and also ship's noise and vibration. On the sea trial, vibration magnitude in the accommodations at NCR was measured at 0.9mm/sec which is only 10% of international allowable magnitude of vibration (9mm/sec). In this paper, a design method for increasing performance of the marine propellers including the WCT propeller is suggested. It is described to maximize the performance of the propeller by adjusting expanded areas of the propeller blade. Results show that efficiency can be increased up to over 2% through the suggested design method.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.6 s.67
• /
• pp.50-57
• /
• 2005

Ice resistance on ice-transiting vessels is one of th￡ important issues concerning th￡ design of ships with ice classes. In this study, th￡ development of GUI software for estimation of ice resistance on ice-transiting vessels is discussed. lee resistance estimation equations, based on model tests and full-scale sea trial data from many previous research articles, are studied in conjunction with two ship categories i.e., ,icebreakers/supply/tug vessels and ice-strengthened cargo vessels. lee resistance estimation equations are summarized in common format and are compared with each other. The GUI software 'Ice View,' written in MS Visual Basic language, can calculate ice resistances according to varying ice thickness and ship speed. The software can provide the calculated results, with suitable tables and graphs, for easy comparison of each ice resistance estimation equation.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.56 no.2
• /
• pp.172-182
• /
• 2020

In order to offer specific information needed to assist in operation of a ship with same type rudder through evaluating the maneuverability of training ship A-Ra with flapped rudder, sea trials based full scale for turning test, zig-zag test with rudder angle 10° and 20°, and spiral test at service condition were carried out on starboard and port sides around Jeju Island according to the standards of maneuverability of IMO. As a result, the angular velocity of port turn was higher than that of starboard turn. Therefore, the size of turning circle was longer on the starboard side. In addition, variation of the transfer due to various factors was more stable than those of the others. In the Z-test results, the mean of 1st and 2nd overshoot angles were 9.8°, 6.3° and 15.3°, 9.2° respectively when the port and starboard was 10°; the 1st overshoot angle were 18°, 13.7° when using 20°. Her maneuverability index T' and K' can be easily determined by using a computer with the data obtained from Z-test where K' and T' are dimensionless constants representing turning ability and responsiveness to the helm, respectively. In the Z-test under flap rudder angle 10°, the obtained K' value covered the range of 2.37-2.87 and T' was 1.74-3.45. Under the flap rudder angle 20°, K' and T' value showed 1.43-1.63, 1.0-1.73, respectively. In the spiral test, the loop width was unstable at +0.3° and -0.5°-0.9° around the midship of flap rudder. As a result, course stability was comparatively good. From the sea trial results, training ship ARA met the present criterion in the standards of maneuverability of IMO.

• Journal of Ship and Ocean Technology
• /
• v.6 no.3
• /
• pp.37-45
• /
• 2002

A series of detailed study was performed to identify the sources of the propeller blade failure and resolve the problem systematically, by use of the theoretical tools and by the direct measurement and observation in the full-scale sea trials. The selection of inexperienced propulsion control system with a reversible gear system is shown to cause the serious damage to the propeller blades in crash astern maneuver, when the rotational direction of the propeller is changed rapidly. Quasi-steady analysis for propeller blade strength using FEM code in bollard backing condition indicates that the safety factor should be order of 18∼20 to avoid the structural failure for the selected propeller geometry and reduction gear system.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.5
• /
• pp.595-602
• /
• 2017

In Korea, much research and development have occurred to enhance the technological competitiveness of tuna purse seining fisheries. Due to these efforts, fishing efficiency has been improved with the development of radar, sonar and global positioning systems for fish detection and revisions to the hull forms of tuna purse seiners. However, for skiff boats, net boats and speed boats, which are auxiliary working boats mounted on tuna purse seiners, technology has lagged behind relative to the modernization of the main vessel. In this study, the hull of an existing propeller-based net boat with steel wire net to protect tuna was changed to the hull of a water jet propulsion vehicle to reduce resistance and improve maneuverability. As a result, a prototype of a water jet propulsion option was produced according to the aluminum structure strength standards specified by the Ministry of Oceans and Fisheries, and safety was confirmed by performing a drop test. Moreover, through a sea trial test, an existing net boat was shown to have a speed of 12.0knots and a towing force of 2,545 kgf at 2,500 RPM. The prototype had a speed of 26.7 knots and a towing force of 2,011 kgf at 3,200 RPM, which satisfied the towing capacity standards of auxiliary working boats mounted on tuna purse seiners.

• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.3
• /
• pp.138-144
• /
• 2013

New experimental devices and methods to measure shaft forces of ships are proposed in this paper. The strain gauge type six-component load cell was newly designed and installed to the end of the propeller shaft. The signals generated from the sensor in the propeller rotating are transferred to the new data amplifying and processing board on the shaft and the data is transmitted to the self-made wireless receiver. To find out the characteristics of shaft forces during port and starboard turning motions in sea trial, oblique and combined yaw maneuvering tests at straight, transient, maximum yaw rate, steady conditions were performed with the model ship installed the shaft forces measuring device using circular motion tester of Samsung Ship Model Basin. Characteristics of the measured shaft forces in model tests show quantitatively good agreement with the computed values obtained by the CFD programs using the measured wake data in oblique towing conditions. In the near future, It is hoped that the estimated shaft forces for a ship from this experimental method could be validated through comparison with directly measured values of a ship.

• Journal of Ocean Engineering and Technology
• /
• v.22 no.4
• /
• pp.84-89
• /
• 2008

It is hard to find experimental data for a model test of small high-speed planning boats. It is difficult to verify the performance seen in a model test for a high-speed boat because the ship-model scale-ratio is very small and the flow velocity of the circulating water channel and the X-carriage speed of the towing tank are restricted. Therefore most hull-form designs for high-speed small boats depend on the sea-trial test result for similar boats or evaluation through numerical calculations. This study investigated the anti-rolling effect of the stern sub-body in a 50-knot doss planning boat. To carry out this work, new model test procedures were set up in the actual sea. Using this method, the anti-rolling effect of the stern sub-body was investigated. A stern sub-body attached to a planning boat was proved to be effective in reducing the roll and pitch angle.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.8
• /
• pp.849-854
• /
• 2013

Many researches on green ship with increasing on economics, efficiency and convenience have been carried out consistently. One of them is development of diesel engines with electronic control. While small duty one for automobiles had been adopted mainly already, disseminating heavy duty one for ships has trouble due to safety and reliability. In order to solve these problem in this study, performance of electronic control and cam type engine installed in parallel on training ship HANBADA of korea maritime university was analyzed and compared. It is certain that specific fuel oil consumption of the electronic control type is lower than cam type and excellent at lower engine load, especially. And the electronic control type shows more effective characteristic at sea trial on specific fuel oil consumption.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.56 no.2
• /
• pp.163-171
• /
• 2020

Engaged in trawling in limited fishing grounds with a number of fish schools could cause collisions between fishing vessels. Therefore, providing accurate maneuver information according to the situation could be regarded as essential for improving seafarers safety and fishing efficiency as well as safety of navigation. It is difficult to obtain all maneuver information through sea trial tests only, so a method through empirical formula is necessary. Since most empirical formulas are developed for merchant ship types, especially the characteristics of hull shape parameter like C_bB/L and dC_b/B etc. are clearly different between fishing vessels and merchant ships, this could occur estimation errors. Therefore, in this study, the authors have selected target fishing vessels and merchant ships and analyzed the characteristics of hull shape parameter according to the ship types. Based on this analysis, the empirical formula developed for the merchant ship type has applied to the target fishing vessels; it has verified through the turning motion simulation that the estimation error could be generated. In conclusion, it is necessary to include the characteristics of the hull shape parameter of fishing vessels in the empirical formula in order to apply the empirical formula has developed for merchant ship types to fishing vessel types.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.2
• /
• pp.133-138
• /
• 2016

This paper describes the track initiation and target-tracking filter for ship tracking in a marine environment by using Light Detection And Ranging (LiDAR). LiDAR with three-dimensional scanning capability is more useful for target tracking in the short to medium range compared to RADAR. LiDAR has rotating multi-beams that return point clouds reflected from targets. Through preprocessing the cluster of the point cloud, the center point can be obtained from the cloud. Target tracking is carried out by using the center points of targets. The track of the target is initiated by investigating the normalized distance between the center points and connecting the points. The regular track obtained from the track initiation can be maintained by the target-tracking filter, which is commonly used in radar target tracking. The target-tracking filter is constructed to track a maneuvering target in a cluttered environment. The target-tracking algorithm including track initiation is experimentally evaluated in a sea-trial test with several boats.