• The Korean Journal of Financial Studies
• /
• v.3 no.2
• /
• pp.281-327
• /
• 1996

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.3
• /
• pp.18-23
• /
• 2001

The effect of pulp consistency on the deinking properties in the ozone deinking of ONP was investigated in order to develop the environmentally friendly deinking method. The pulp consistency and ozone treatment time were varied for this purpose. Higher pulp consistency during ozone treatment gave better ink removal efficiency than the conventional deinking method. In was also found that the increase of pulp consistency can decrease the ozone treatment time which can meet the deinking quality. WRV of ozone deinked pulp obtained at 10% and 30% of pulp consistencies was lower than those of the conventional deinking method. However, the higher pulp consistency during ozone treatment improved WRV. Highest brightness was obtained at the ozone treatment condition of 30% pulp consistency and 10 minutes. The lower brightness at the other ozone treatment condition should be originated from the excessive decrease of ink particle size and then decrease of true ink removal efficiency. Scott bond was increased with the increase of pulp consistency and treatment time. However, the improvement of breaking length with ozone treatment was no significant.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.1
• /
• pp.38-44
• /
• 2001

The effects of refining load on the paper properties were investigated. HwBKP, SwBKP and SwUKP were refined with PFI mill at the load of 3.33 N/mm and 6.00 N/mm. Higher Scott bond was obtained at the higher refining load for three pulp used in this study. However any changes in the light scattering coefficient with the change of refining load were not observed. Although the effect of refining load on the formation index for SwUKP was not observed, higher refining load gave the better formation for HwBKP and SwBKP. The fiber mass and fiber crowding factor were not affected by the refining load. Higher apparent density and tensile index were obtained with the higher refining load. However, the higher refining load did not improve the tensile index at the same apparent density. The tear index was decreased with the increase of refining load.

• Nuclear Engineering and Technology
• /
• v.55 no.2
• /
• pp.432-442
• /
• 2023

Characterizing the behavior of nuclear reactor plate fuels is vital to the progression of advanced fuel systems. The states of pre- and post-irradiation plates need to be determined effectively and efficiently prior to and following irradiation. Due to the hostile post-irradiation environment, characterization must be completed remotely. Laser-based characterization techniques enable the ability to make robust measurements inside a hot-cell environment. The Laser Shock (LS) technique generates high energy shockwaves that propagate through the plate and mechanically characterizes cladding-cladding interfaces. During an irradiation campaign, two Idaho National Laboratory (INL) fabricated MP-1 plates had a fuel breach in the cladding-cladding interface and trace amounts of fission products were released. The objective of this report is to characterize the cladding-cladding interface strengths in three plates fabricated using different fabrication processes. The goal is to assess the risk in irradiating future developmental and production fuel plates. Prior LS testing has shown weaker and more variability in bond strengths within INL MP-1 reference plates than in commercially produced vendor plates. Three fuel plates fabricated with different fabrication processes will be used to bound the bond strength threshold for plate irradiation insertion and assess the confidence of this threshold value.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.1
• /
• pp.41-47
• /
• 2000

The objective of this study is to assess the possibility of ozone as an environmentally friendly new deinking alternative for conventional deinking method. It is well known that the white ledger is very difficult to deink because the toner ink has the peculiar shape and size. Ozonization could remove the ink particles above 300 microns and thus improved the ink removal efficiency. Ozonization also improved the WRV of recycled fiber and apparent density, scott bond strength , breaking length, double fold and tear index. Thus, we believe that ozonization could be used as a deinking means of white ledger instead of the convention미 deinking method.

• Computers and Concrete
• /
• v.3 no.2_3
• /
• pp.79-90
• /
• 2006

This paper describes the results of an investigation into high mass-low velocity impact behaviour of reinforced concrete beams. Tests have been conducted on fifteen 2.7 m or 1.5 m span beams under drop-weight loads. A high-speed video camera has been used at rates of up to 4,500 frames per second in order to record the crack formation, propagation, particle spallation and scabbing. In some tests the strain in the reinforcement has been recorded using "Durham" strain gauged bars, a technique developed by Scott and Marchand (2000) in which the strain gauges are embedded in the bars, so that the strains in the reinforcement can be recorded without affecting the bond between the concrete and the reinforcement. The impact force acting on the beams has been measured using a load cell placed within the impactor. A high-speed data logging system has been used to record the impact load, strains, accelerations, etc., so that time histories can be obtained. This research has led to the development of computational techniques based on combined continuum/discontinuum methods (finite/discrete element methods) to permit the simulation of impact loaded reinforced concrete beams. The implementation has been within the software package ELFEN (2004). Beams, similar to those tested, have been analysed using ELFEN a good agreement has been obtained for both the load-time histories and the crack patterns.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.30 no.2
• /
• pp.5-12
• /
• 1998

Exploitation of the papermaking technology to reduce the strength loss that accompanies when using recycled papers as raw materials for papermaking is one of the most important issues imposed upon today's paper industry. Multi-layer sheet forming technology has been suggested as a way that provides some answers to this issue. In this study strength properties of single- and two-layer handsheets formed with recycled fiber and unbleached softwood kraft pulp have been examined to quantify the benefits when using two-layer sheet forming technology rather than a conventional single layer sheet forming precess. Single- and two-layer handsheets were made from 50% of OCC and 50% of Sw-UKP and their strength properties were evaluated. Also the strength properties made from Sw-UKP and OCC sheets were determined. A multihead, which can be attached on the top of hand- sheet former, was used to form two-layer sheets. Maximum strength properties could be obtained in the freeness range of 500∼300mL CSF for Sw-UKP Most of the strength properties was reduced by 30∼35% when 50% OCC was blended with UKP. Decrease of strength properties, however, could be reduced by employing a two-layer sheet forming method. Creator strengths could be obtained when UKP was positioned at the top layer of two layered sheets indicating greater UKP fines retention due to the filtration effect of the OCC layer formed prior to UKP layer contributed the strength improvement. Two-layer sheet showed lower Scott internal bond strength than single layer sheet. By incorporating some of UKP fibers into OCC layer this reduction could be reduced.