• Journal of the Korean Ceramic Society
• /
• v.40 no.11
• /
• pp.1047-1057
• /
• 2003

A sub-nanometer resolution Scanning Nonlinear Dielectric Microscope (SNDM) was developed for observing ferroelectric polarization. We also demonstrate that the resolution of SNDM is higher than that of a conventional piezo-response imaging. Secondly, we report new SNDM technique detecting higher nonlinear dielectric constants $\varepsilon$$\_$3333/ and $\varepsilon$$\_$33333/. Higher order nonlinear dielectric imaging provides higher lateral and depth resolution. Finally, the formation of artificial small inverted domain is reported to demonstrate that SNDM system is very useful as a nano-domain engineering tool. The nano-size domain dots were successfully formed in LiTaO$_3$ single crystal. This means that we can obtain a very high density ferroelectric data storage with the density above 1T-bits/inch$^2$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.2
• /
• pp.133-136
• /
• 2010

Laser direct patterning is one of new methods which are able to replace a conventional photolithography. In order reduce the fabrication cost and to improve the luminous efficiency of AC plasma display panels (PDPs), in this experiment, a Q-switched Nd:$YVO_4$ laser was used to fabricate T-shaped indium tin oxide (ITO) display electrodes. For the laser beam scanning speed from 100 mm/sec to 800 mm/sec, T-shaped ITO patterns were clearly obtained and investigated. The experimental results showed that the optimized T-shaped ITO electrode was obtained when the lasers scanning speed was 300 mm/s.

• International conference on construction engineering and project management
• /
• 2005.10a
• /
• pp.1193-1198
• /
• 2005

The pre-assembly takes a large portion of the fabrication cost of steel bridges. In order to save the fabrication cost through the improvement of the conventional pre-assembling process, this research investigates a numerical pre-assembly simulation as an alternative to current pre-assembling process. The 3D laser scanning was utilized in site and measuring data for steel box were analyzed. The productivity of pre-assembly simulation system is compared with the conventional pre-assembling system. This paper identifies feasibility on the alternative pre-assembling process and then proposes the scheme of the pre-assembly simulation system development satisfying the current pre-assembly inspection of standards.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.595-598
• /
• 2014

In order to provide the Mobile Stations operating in IEEE 802.11 Wireless LAN network with seamless handover, a comprehensive study on the functions of handover considering various networking environments and characteristics of Mobile Stations is required. Note that the channel scan process finding a new AP takes the major portion of handover time, and this is the most significant issue with seamless handover for real-time multimedia service in WLAN environment. In this paper the functions required to provide seamless handover in IEEE 802.11 WLAN network are identified, and a new scanning technique is proposed with which the Mobile Stations can selectively scan the channels to reduce the channel scan time in various network environments. Here each Mobile Station awares of the channels the neighbor APs are using by scanning them in advance according to the proposed technique. Afterwards, when handover is actually required, the optimal AP is decided quickly by scanning only the predetemined group of channels and order of scan without unnecessary scan of all the channels. In addition, proposes to enter the Scan Trigger Value and Handover Threshold Value in mobile phones in order to prevent the phenomenon can not handover.

• Korean Journal of Computational Design and Engineering
• /
• v.21 no.3
• /
• pp.296-305
• /
• 2016

This paper proposes a framework to automatically align Dental range image captured by depth sensors like the Microsoft Kinect. Aligning dental images by intraoral scanning technology is a difficult problem for applications requiring accurate model of dental-scan datasets with efficiency in computation time. The most important thing in dental scanning system is accuracy of the dental prosthesis. Previous approaches in intraoral scanning uses a Z-buffer ICP algorithm for fast registration, but it is relatively not accurate and it may cause cumulative errors. This paper proposes additional Alignment using the rough result comes after intraoral scanning alignment. It requires that Each Depth Image of the total set shares some overlap with at least one other Depth image. This research implements the automatically additional alignment system that aligns all depth images into Completed model by computing a network of pairwise registrations. The order of the each individual transformation is derived from a global network and AABB box overlap detection methods.

• Korean Journal of Optics and Photonics
• /
• v.10 no.4
• /
• pp.267-272
• /
• 1999

We attached a fiber tip on the branch of a quartz crystal oscillator in order to make a feedback control system for near field optical microscope. The electrical impedance of the quartz crystal oscillator depends on the distance between the surface of the sample and the tip caused by the surface damping. Using this method, we can directly monitor the distance between the sample and the tip without inserting extra beam which might give extra optical noise. We characterize the XY scanning resolution and the amplitude of the vibrating tip and the Z-dependent decay of the evanescent wave.

• The Journal of Health Technology Assessment
• /
• v.6 no.2
• /
• pp.156-161
• /
• 2018

Objectives: To evaluate results and workloads of the horizon scanning of the emerging health technology since 2014 to 2016. Methods: In order to analyze the results of the emerging health technology, we identified the number of research procedure between 2014 and 2016. The sixteen findings were calculated annual workload by person, and categorized by medical phase, classification of disease, and healthcare technology. Results: An average of 5.67 personnel were involved over three years, assessment of each emerging healthcare technology was performed for each person of identifying 54 cases, filtering 2.4 cases, prioritizing 0.9 cases were performed. According to the mapping by healthcare technologies, nine medical devices (56.3%), six drugs (37.5%), and one material of the medical treatment (6.3%) were assessed. Among sixteen findings, fifteen cases were health technologies for treatment and only one case for diagnosis. Conclusion: Future plans of the horizon scanning of the emerging health technology is required appropriate manpower in charge each target number of assessment. And a legal basis should be provided for policy reflection rate. Furthermore, an evaluation criteria and procedures should be transparent to avoid a conflict of interest.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.16 no.11
• /
• pp.3680-3693
• /
• 2022

The handover procedure of IEEE 802.11 wireless local area networks (WLANs) introduces significant delay, which can degrade the quality of service (QoS) especially for delay-sensitive applications. Although studies have been conducted to support handover in SDN-based WLAN, there is no research to reduce the channel scanning procedure that takes up the most delay time in the handover process. The channel scanning procedure is essential to determine the appropriate access point (AP). To mitigate this problem, this paper proposes a SWITCH: SDN-WLAN integrated handover scheme for QoS-Guaranteed mobile service. In SWITCH, each AP periodically broadcasts beacon frames through different channels in a predetermined order that includes the operating channel information of the AP. This allows mobile stations (MSs) to receive the beacon frames of nearby APs, and therefore they can determine the appropriate APs for handover without the channel scanning procedure. By reporting the information of the newly moved AP to the SDN controller, a flow rule is installed in advance to provide fast handover, and packet loss is reduced by buffering data destined for MS. In addition, the proposed scheme can adaptively operate SWITCH to consider the user location and QoS requirement of flow to save radio resource overhead. Performance evaluation results demonstrate that SWITCH can reduce the handover delays, flow table utilization ratio and radio resource overhead while improving the network throughput.

• Journal of Korea Society of Industrial Information Systems
• /
• v.20 no.5
• /
• pp.25-35
• /
• 2015

Handoff is a critical issue for seamless roaming in IEEE 802.11-based wireless networks. In order to provide real-time services, handoff mechanism must be provided. However, the IEEE 802.11 standard handoff is not appropriate to provide the services, because it is based on the full-scanning approach which spends too much time searching Access Point (AP). In this paper, we propose a new scheme, which can reduce the scanning latency. A station performs full-scanning operation for finding APs when it enters wireless networks for the first time. The station sends the scanned channel information to AP. AP maintains the neighbor channel table based on the information received from stations. A station performs the partial-scanning by using the table. Therefore, the proposed scheme can reduce the scanning latency.

• Journal of KIBIM
• /
• v.9 no.1
• /
• pp.11-21
• /
• 2019

Recently, there is an increase in fire incidents in building structures. Due to this, the importance of fire-damaged buildings' safety diagnosis and evaluation after fire is growing. However, the existing fire-damaged safety diagnosis and evaluation methods are personnel-oriented, so the diagnostic results are intervened by investigators' subjectivity and unquantified. Thus, improper repair and reinforcement can result in secondary damage accidents and economic losses. In order to overcome these limitations, this study proposes using 3D laser scanning technology. The case analysis of fire-damaged building structures was conducted to verify the effectiveness of accuracy and manpowering by comparing the existing method and the proposed method. The proposed method using 3D laser scanning technology to obtain point cloud data of fire-damaged field. The point cloud data and BIM model is combined to inspect the fire-damaged area and depth. From inspection, quantified repair and reinforcement quantity take-off can be acquired. Also, the proposed method saves half of the manpowering within same time period compared to the existing method. Therefore, it seems that using 3D laser scanning technology in fire-damaged safety diagnosis and evaluation will improve in accuracy and saving time and manpowering.