• Journal of Korean Society of Water and Wastewater
• /
• v.24 no.3
• /
• pp.341-349
• /
• 2010

It is well known that manganese is hard to oxidize under neutral pH condition in the atmosphere while iron can be easily oxidized to insoluble iron oxide. The purpose of this study is to identify removal mechanism of manganese in the D water treatment plant where is treating bank filtered water in aeration and rapid sand filtration. Average concentration of iron and manganese in bank filtered water were 5.9 mg/L and 3.6 mg/L in 2008, respectively. However, their concentration in rapid sand filtrate were only 0.11 mg/L and 0.03 mg/L, respectively. Most of the sand was coated with black colored manganese oxide except surface layer. According to EDX analysis of sand which was collected in different depth of sand filter, the content of i ron in the upper part sand was relatively higher than that in the lower part. while manganese content increased with a depth. The presence of iron and manganese oxidizing bacteria have been identified in sand of rapid sand filtration. It is supposed that these bacteria contributed some to remove iron and manganese in rapid sand filter. In conclusion, manganese has been simultaneously removed by physicochemical reaction and biological reaction. However, it is considered that the former reaction is dominant than the latter. That is, Mn(II) ion is rapidly adsorbed on ${\gamma}$-FeOOH which is intermediate iron oxidant and then adsorbed Mn(II) ion is oxidized to insoluble manganese oxide. In addition, manganese oxidation is accelerated by autocatalytic reaction of manganese oxide. The iron and manganese oxides deposited on the surface of the sand and then are aged with coating sand surface.

• Geomechanics and Engineering
• /
• v.7 no.3
• /
• pp.297-316
• /
• 2014

This paper presents a detailed study focused on investigating the effects of silt content on the static and dynamic properties of sand-silt mixtures. Specimens with a low-plastic silt content of 0, 15, 30 and 50% by weight were tested in static triaxial, cyclic triaxial, and resonant columns in addition to consolidation tests to determine such parameters as compression index, internal friction angle, cohesion, cyclic stress ratio, maximum shear modulus, normalized shear modulus and damping ratio. The test procedures were performed on specimens of three cases: constant void ratio index, e = 0.582; same peak deviator stress of 290 kPa; and constant relative density, $D_r$ = 30%. The test results obtained for both the constant-void-ratio-index and constant-relative-density specimens showed that as silt content increased, the internal friction angle, cyclic stress ratio and maximum shear modulus decreased, but cohesion increased. In testing of the same deviator stress specimens, both cohesion and internal friction angle were insignificantly altered with the increase in silt content. In addition, as silt content increased, the maximum shear modulus increased. The cyclic stress ratio first decreased as silt content increased to reach the threshold silt content and increased thereafter with further increases in silt content. Furthermore, the damping ratio was investigated based on different silt contents in three types of specimens.

• Journal of Korean Society of Water and Wastewater
• /
• v.21 no.4
• /
• pp.503-508
• /
• 2007

Small scale D-water treatment plant(WTP) where has slow sand filtration was using raw water containing high concentration of manganese (> 2mg/l). The raw water was pre-chlorinated for oxidation of manganese and resulted in difficulty for filtration. Thus, sometimes manganese concentration and turbidity were over the water quality standard. Two stage rapid manganese sand filtration pilot plant which can treat $200m^3/d$ was operated to solve manganese problem in D-WTP. The removal rate of manganese and turbidity were about 38% and 84%, respectively without pH control of raw water. However, when pH of raw water was controlled to average 7.9 with NaOH solution, the removal rate of manganese and turbidity increased to 95.0% and 95.5%, respectively and the water quality of filtrate satisfied the water quality standard. Manganese content in sand was over 0.3mg/g which is Japan Water Association Guideline. The content in upper filter was 5~10 times more than that of middle and lower during an early operation but the content in middle and lower filter was increased more and more with increase of operation time. This result means that the oxidized manganese was adsorbed well in sand. Rapid manganese sand filter was backwashed periodically. The water quality of backwash wastewater was improved by sedimentation. Thus, turbidity and manganese concentration decreased from 29.4NTU to 3.09NTU and from 1.7mg/L to 0.26mg/L, respectively for one day. In Jar test of backwash wastewater with PAC(Poly-aluminum chloride), optimum dosage was 30mg/L. Because the turbidity of filtrate was high as 0.76NTU for early 5 minute after backwash, filter-to-waste should be used after backwash to prevent poor quality water.

• The Korean Journal of Mycology
• /
• v.21 no.3
• /
• pp.235-245
• /
• 1993

The symbiotic properties of arbuscular mycorrhizal fungi(AMF) such as the absence and/or presence of symbiosis, spore density, and six factors of phycochemical properties of soil were investigated in the rhizosphere of seven sand dune plants and three control plants around Kum river. The infection of AMF was confirmed in all plants. Three genera, nine species of the AMF spores were identified in the sand dune; Ac. scrobiculata, G. aggregatum, G. convolutum, G. diaphanum, G. dimophicum, G. geosporum, G. vesiculiferum, G. tortuosum, S. pachycaulis. All of them were also found in the control, but S. pachycaulis were only separated in the sand dune. In the control, three genera, four species were identified; G. flavisporum, Gi. margarita, Sc. gregaria. Sc. persica. The species specificity was not found between the sand dune plant and AMF. However, the AMF was thought to be correlated with the soil factors. The spore density was stimulated with increase of the organic matter and the nitrogen content, but inhibited with the water content and the phosphorus content. In respect of the seasonal factor, the spore density was increased in the late growth period of plants.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.4
• /
• pp.91-100
• /
• 2007

In most design codes, soils are classified as either sand or clay, and appropriate design equations are used to represent their behavior. For example, the behavior of sandy soils is expressed in terms of the relative density, whereas consistency limits are often used for clays. However, sand-clay mixtures, which are typically referred to as intermediate soils, cannot be easily categorized as either sand or clay and therefore a unified interpretation of how the soil will behave at the transition point, i.e., from sandy behavior when fines are low to clay behavior for high fines content, is necessary. In this study, active natural clays are mixed with sand, and the fines content varied in order to produce different structures, ranging from one state where only sand particles form the soil structure to another where the matrix of fines make-up the structure. While paying attention to the granular void ratio in order to clarify the shear properties of sand-clay mixtures with increasing fines content monotonic, shear tests were performed on isotropically, and anisotropically consolidated specimens. From the test results, it was observed that the monotonic shear strength of sand-clay mixtures is dependent on the granular void ratio.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.3
• /
• pp.13-21
• /
• 2002

An extensive tension experiment was carried out to examine the variation of tensile strength in moist sand having moisture contents in the range of 0.5% < w < 4.0% with newly developed direct tension apparatus. It was observed that tensile strength of sand varied as functions of moisture content, relative density, presence of fines, and level of precompression. Tensile strength increases with increasing moisture content and fines, and this trend is more noticeable at increasing relative densities. However, the influences of relative density and fines on the tensile strength are substantially dependent on the water content. These effects are reduced at low moisture levels (w < 0.5%). The precompression effects also depend on the water content but less on the duration and level of the precompression.

• The Korean Journal of Ecology
• /
• v.7 no.2
• /
• pp.74-84
• /
• 1983

The dominant species of the sand vegetation in the western coast of Korea were Carex pumila, Ischaemum antheporoides, Calystegia soldanella, Carex kobomugi and Imperata cylindrica var. koenigii. The salt content of the sand dune soil and of the atmosphere of surveyed areas ranged from 3.93 to 13.86 mg% and from 25.81 to 168.86mg% respectively. Between the salt content of the atmosphere and that of the soil positive relationship was found. Species density and Simpson's index increased with the distance from the coast, the former was exponential, however, the latter was linear. The composition of biological types in the investigated stands were H-D4-R1-3-e or H-D4-R1-3-t. Relative numbers of psammophytes and rhizome psammophytes decreased with the distance from the coast, but those of other plants increased. The standing crop of the sand dune vegetation ranged from 0.04 to 491.64g/m2 and the average 27.77g/m2. This was varied as the stands and showed a linear increment as the distance from the coast was increased. The salt content of atmosphere significantly affected the density, T/R ratio in the standing crop and Simpson's index. The salt content of soil showed similar tendency on the density and the T/R ratio.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.8
• /
• pp.13-24
• /
• 2011

In the part of geotechnical engineering, soils are classified as either the coarse grained soil or the fine-grained soil following the fine content($F_c$=50%) according to the granularity, and appropriate design codes are used respectively to represent their mechanical behaviour. However, sand-clay mixtures, which are typically referred to as intermediate soils, cannot be easily categorized as either sand or clay. In this study, several monotonic undrained shear tests were carried out on Silica sand fine mixtures with various proportions, and a wide range of soil structures, ranging from one with sand dominating the soil structure to one with fines controlling the behaviour, were prepared using compaction method or pre-consoldation methods in prescribed energy. The shear strength of mixtures below the threshold fines content is observed that as the fines content increases, maximum deviator stress ratio decrease for dense samples while an increase is noted for loose samples. Then, by using the concept of fines content and granular void ratio, the monotonic shear strength of the mixtures was estimated. It was found that the shear behavior of mixtures is greatly dependent on the skeleton structure of sand particles.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.455-458
• /
• 2005

This study compares the concrete using natural sand with the concrete using crush sand for the examination for the properties of a concrete. In the fresh concrete, the concrete using crush sand has less of the quantity of consistency, the content of air, and bleeding than the concrete using natural sand, and the concrete using crush sand has faster setting time than the concrete using natural sand. In hardening concrete, the concrete using crush sand has higher compressive strength and tensile strength than the concrete using natural sand because minute particles fill up a gap. Drying shrinkage of the concrete using natural sand is less than the concrete using crush sand.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.383-386
• /
• 2005

This paper is to investigate the effect of W/B, blend ratio of crushed sand with sea sand on fluidity and strength properties of high strength concrete utilizing crushed sand. W/B set up 0.25, 0.30, 0.35 and the blend ratio of crushed sand with sea sand set up 0:100, 30:70, 50:50, 70:30, 100:0 The results of this study are summarized as the follows; 1) The increase of the blend rate of crushed sand, affected on the enhancement of flow, the increase of dosage of SP and water content, but the decrease S/a 2) Compressive strength is increased when crushed sand $30\~70\%$ was replaced with sea sand. 3) The optimal replacement percentage of crushed sand is $50\%$ with sea sand.