• Journal of The Korean Society of Agricultural Engineers
• /
• v.51 no.3
• /
• pp.37-43
• /
• 2009

The objective of this study was to investigate the basic relationships between spectral reflectance and varying concentrations of sediment in surface waters. An experimental method for determining suspended sediment concentration (SSC) in the water by use of a spectroradiometer above the water surface, in visible and near-infrared (NIR) wavelengths, is applied. The main advantage of the method is the direct comparison of spectral reflectance and the SSC, but it requires an accurate knowledge of the water body and sediment. Therefore numerous spectroradiometric measurements are carried out in situ measurements, for SSC, ranging from zero to 100 percentage and two types of sediment applied in the water tank. The results indicate that the suspended sediment causes increasing spectral reflectance response in waters. We observed that spectral reflectance increases with SSC, first at the lower wavelengths (430-480 nm), then in the middle wavelengths (570-700 nm), and finally, in the NIR domain (800-820 nm); a characteristic maximum reflectance appears at 400-670 nm. Relationships between the wavelength, integral value, and the SSC were evaluated on the basis of the regression analysis. The regression curve for the relation between the wavelength, integral value, and the SSC were determined ($R^2$>0.98). Finally, the specular wavelength can be estimated to recognize the sediment and to improve SC estimation accuracy in the water.

• Korean Journal of Plant Resources
• /
• v.28 no.4
• /
• pp.533-540
• /
• 2015

Germination properties, leachate electrical conductivity (EC), and inorganic compound leaching were analyzed to ascertain the storage ability and change of physiological characteristics during storage of Hippophae rhamnoides seeds. Seeds were placed in an incubator at 25℃ and sown in different soil media (sand, vermiculite and horticultural substrate) after being stored for 6, 18 and 30 months at 2℃. All germination properties decreased in accordance to an increase of the seed storage period. Compared with the seed storage for 18 months, germination percentage (GP), germination performance index (GPI), and germination value (GV) of seeds stored for 30 months decreased by more than 50%. When the seeds were sown in different soil media in a greenhouse, those germination properties were similar to the seeds germinated in an incubator, and mean germination time, GPI and GV had a significant difference except GP among soil media. EC and inorganic ion concentration had a strong positive correlation with the seed storage period, but the ratios of inorganic ions from stored seeds revealed that K⁺/Mg²⁺ and Na⁺/Mg²⁺ were inversely correlated with the storage period.

• Computers and Concrete
• /
• v.13 no.4
• /
• pp.531-545
• /
• 2014

The purpose of this paper is to develop a prediction model for the compressive strength of waste LCD glass applied in concrete by analyzing a series of laboratory test results, which were obtained in our previous study. The hyperbolic function was used to perform the nonlinear-multivariate regression analysis of the compressive strength prediction model with the following parameters: water-binder ratio w/b, curing age t, and waste glass content G. According to the relative regression analysis, the compressive strength prediction model is developed. The calculated results are in accord with the laboratory measured data, which are the concrete compressive strengths of different mix proportions. In addition, a coefficient of determination $R^2$ value between 0.93 and 0.96 and a mean absolute percentage error MAPE between 5.4% and 8.4% were obtained by regression analysis using the predicted compressive analysis value, and the test results are also excellent. Therefore, the predicted results for compressive strength are highly accurate for waste LCD glass applied in concrete. Additionally, this predicted model exhibits a good predictive capacity when employed to calculate the compressive strength of washed glass sand concrete.

• Advances in concrete construction
• /
• v.8 no.2
• /
• pp.127-137
• /
• 2019

Roller Compacted Concrete (RCC) is a zero slump concrete consisting of a mixture of cementitious materials, sand, dense graded aggregates and water. In this study, an attempt has been made to investigate the effect of aggregate type on strength and abrasion resistance of RCC made by using granulated blast furnace slag (GGBS) as partial replacement of cement. Mix proportions of RCC were finalized based upon the optimum water content achieved in compaction test. Two different series of RCC mixes were prepared with two different aggregates: crushed gravel and limestone aggregates. In both series, cement was partially replaced with GGBS at a replacement level of 20%, 40% and 60%. Strength Properties and abrasion resistance of the resultant mixes was investigated. Abrasion resistance becomes an essential parameter for understanding the acceptability of RCC for rigid pavements. Experimental results show that limestone aggregates, with optimum percentage of GGBS, perform better in compressive strength and abrasion resistance as compared to the use of crushed gravel aggregates. Observed results are further supported by stoichiometric analysis of the mixes by using basic stoichiometric equations for hydration of major cement compounds.

• Computers and Concrete
• /
• v.24 no.1
• /
• pp.1-6
• /
• 2019

Within the scope of this study, the foam solution was prepared by properly mixing sulfonate based foam agent with water. Furthermore, this solution was mixed with the mixture of fine sand, cement, and water to produce foamed concrete. The mixture ratios which are the percentage of foam solution used in foam concrete were chosen as 0, 20, 40 and 60% by vol. After these groups reached 28 days of strength, they were heated to 20, 100, 400 and $700^{\circ}C$ respectively. Afterward, high-temperature effects on the foamed concrete were obtained by employing physical and mechanical properties tests. Additionally, SEM (scanning electron microscope) and EDX (energy-dispersive X-ray spectroscopy) tests were employed to analyze the microstructure, and ${\mu}-CT$ (micro computed tomography) images were used to reconstruct 3-D models of the heat-treated specimens. Then, these models are analyzed to examine the void structures and the changes in these structures due to the high temperatures. The study has shown that the void structures reduce the high-temperature effects and the foam solution could be mixed with concrete up to 40 % by vol. where the high strength of foamed concrete is non-mandatory.

• Advances in concrete construction
• /
• v.13 no.3
• /
• pp.233-242
• /
• 2022

An attempt is made to develop an eco-friendly concrete with ground granulated blast furnace slag (GGBS) and pond ash as partial replacement materials for cement and fine aggregate, respectively without compromising the strength and durability. Sixteen concrete mixes were developed by replacing cement and fine aggregate by GGBS and pond ash, respectively in stages of 10%. The maximum replacement levels of cement and fine aggregates were 50% and 30% respectively. Experimental results revealed that the optimum percentage of GGBS and pond ash replacement levels were 30% and 20% respectively. The optimized mix was used further to study the flexural behavior and durability properties. Reinforced Concrete (RC) beams were cast and tested under a four-point bending configuration. Also, the specimens prepared from the optimized mix were subjected to alternate wet and dry cycles of acid (3.5% HCl and H₂SO₄) and sulphate (10% MgSO₄) solutions. Results show that the optimized concrete mix with GGBS and pond ash had a negligible weight loss and strength reduction.

• Geomechanics and Engineering
• /
• v.36 no.4
• /
• pp.343-353
• /
• 2024

The hydraulic anisotropic behavior of unsaturated soil has not been fully explored in relation to the grain-size distribution. The present study conducted laboratory assessments to examine the hydraulic anisotropy condition of statically compacted specimens in various initial states. The investigation incorporated the concept of hydraulic anisotropy by employing two discrete forms of soil stratification: horizontal-layering (HL) and vertical-layering (VL). The examined soils comprised sandy silt and silty sand, exhibiting either unimodal or bimodal soil-water characteristic curve (SWCC). This study aimed to investigate the potential correlation between the hydraulic anisotropy ratio and soil properties. The present study established a correlation between the hydraulic anisotropy ratio and several soil parameters, including fine content, dry density, plastic limit, and liquid limit. The study results indicate a non-linear relationship between the percentage of fine and dry density in soils with unimodal and bimodal soil-water characteristic curve (SWCC) and hydraulic anisotropy ratio.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.7
• /
• pp.49-62
• /
• 2022

The hollow modular concrete block reinforced foundation method is one of the ground reinforcement foundation methods that uses hexagonal honeycomb-shaped concrete blocks with mixed crushed rock to reinforce soft grounds. It then forms an artificial layered ground that increases bearing capacity and reduces settlement. The hollow modular honeycomb-shaped concrete block is a geometrically economical, stable structure that distributes forces in a balanced way. However, the behavioral characteristics of hollow modular concrete block reinforced foundations are not yet fully understood. In this study, a bearing capacity test is performed to analyze the reinforcement effectiveness of the hollow modular concrete block through the laboratory model tests. From the load-settlement curve, punching shear failure occurs under the unfilled sand condition (A-1-N). However, the filled sand condition (A-1-F) shows a linear curve without yielding, confirming the reinforcement effect is three times higher than that of unreinforced ground. The bearing capacity equation is proposed for the parts that have contact pressure under concrete, vertical stress of hollow blocks, and the inner skin friction force from horizontal stress by confining effect based on the schematic diagram of confining effect inside a hollow modular concrete block. As a result of calculating the bearing capacity, the percentage of load distribution for contact force on the area of concrete is about 65%, vertical force on the area of hollow is 16.5% and inner skin friction force of area of the inner wall is about 18.5%. When the surcharge load is applied to the concrete part, the vertical stress occurs on the area of the hollow part by confining effect first. Then, in the filled sand in the hollow where the horizontal direction is constrained, the inner skin friction force occurs by the horizontal stress on the inner wall of the hollow modular concrete block. The inner skin friction force suppresses the punching of the concrete part and reduces contact pressure.

• Economic and Environmental Geology
• /
• v.44 no.1
• /
• pp.59-70
• /
• 2011

The surface sediment distribution in a tidal flat in 2001 was compared with that of 2008 using high spatial resolution remote sensing images and a GIS-based analysis. Maps of the surface sedimentary facies for each time frame were induced by an IKONOS data acquired in February, 2001 and a KOMPSAT-2 data acquired in April, 2008 using an object-based classification method. The area ratio of each surface sedimentary facies were estimated, and the results were compared each other for deducing the change in the sedimentary facies during the time interval. The result showed that the percentage of grains larger than very fine sand (0.0625 mm) has increased considerably since the early 2000s in the Hwangdo tidal flat. Mud flat facies has decreased 5.81 % in the late 2000s compared with the early 2000s. However, mixed flat and sand flat have increased 4.46% and 2.14%, respectively. A field campaign also supported the result. This study showed that the monitoring of changes in the surface sedimentary facies in the tidal flat is possible through a GIS-based analysis using high spatial resolution remote sensing images.

• Korean Journal of Soil Science and Fertilizer
• /
• v.37 no.4
• /
• pp.207-211
• /
• 2004

Evaluation of wind erodibility for the Saemangeum Reclamation Project area based on the wind erosion equation, WEQ, was attempted. Climatic factor was calculated with the climatic data for the Kunsan area, and soil erodibility factor was evaluated with the 108 soil samples collected from the project area. The soil erodibility evaluated from the non erodible aggregate percentage greater than 0.84 mm for the soil samples collected was $204.1Mg\;ha^{-1}\;yr^{-1}$ ranged from 50.08 to $642.37ha^{-1}\;yr^{-1}$. The annual climate factor based on the meteorological data in Kunsan was 3.67. The average amount of wind erosion with climate factor C from the climatic data from Kunsan and soil erodibility factor l from the soil in the project area was 7.49 Mg $ha^{-1}$ $yr^{-1}$ ranged from 1.84 Mg $ha^{-1}$ $yr^{-1}$ for silty clay loam soil to 23.57 Mg $ha^{-1}$ $yr^{-1}$ for sandy soil. The intensive wind erosion control should be needed for friable sand and loamy sand soils in the area.