• 한국표면공학회지
• /
• 제51권5호
• /
• pp.303-308
• /
• 2018

Currently hydrofluoric acid (HF) based glass etch method is widely used for anti-glare (AG) surface treatment since it can effectively alleviate the specular reflection problem with relatively low processing cost. However, due to the environmental regulation and safety problem, it is essential to develop alternative technology to replace this method. For this, in this paper, we propose sand blasting based AG surface treatment method for display glass. To characterize the sand blasting process, surface roughness, haze, surface durability, and flatness are considered as process outputs and central composite design (CCD) method and response surface model (RSM) method are applied to model each process output. Models for surface roughness and haze showed 96.44% and 97.24% of R-squared values, respectively and they can be applied to optimize AG surface treatment process for various haze level requirements of display industries.

• 한국재료학회지
• /
• 제31권2호
• /
• pp.75-83
• /
• 2021

To cope with automobile exhaust gas regulations, ISG (Idling Stop & Go) and charging control systems are applied to HEVs (Hybrid Electric Vehicle) for the purpose of improving fuel economy. These systems require quick charge/discharge performance at high current. To satisfy this characteristic, improvement of the positive electrode plate is studied to improve the charge/discharge process and performance of AGM(Absorbent Glass Mat) lead-acid batteries applied to ISG automotive systems. The bonding between grid and A.M (Active Material) can be improved by applying the Sand-Blasting method to provide roughness to the surface of the positive grid. When the Sand-Blasting method is applied with conditions of ball speed 1,000 rpm and conveyor speed 5 M/min, ideal bonding is achieved between grid and A.M. The positive plate of each condition is applied to the AGM LAB (Absorbent Glass Mat Lead Acid Battery); then, the performance and ISG life characteristics are tested by the vehicle battery test method. In CCA, which evaluates the starting performance at -18 ℃ and 30 ℃ with high current, the advanced AGM LAB improves about 25 %. At 0 ℃ CA (Charge Acceptance), the initial charging current of the advanced AGM LAB increases about 25 %. Improving the bonding between the grid and A.M. by roughening the grid surface improves the flow of current and lowers the resistance, which is considered to have a significant effect on the high current charging/discharging area. In a Standard of Battery Association of Japan (SBA) S0101 test, after 300 A discharge, the voltage of the advanced AGM LAB with the Sand-Blasting method grid was 0.059 V higher than that of untreated grid. As the cycle progresses, the gap widens to 0.13 V at the point of 10,800 cycles. As the bonding between grid and A.M. increases through the Sand Blasting method, the slope of the discharge voltage declines gradually as the cycle progresses, showing excellent battery life characteristics. It is believed that system will exhibit excellent characteristics in the vehicle environment of the ISG system, in which charge/discharge occurs over a short time.

• 터널과지하공간
• /
• 제7권1호
• /
• pp.51-57
• /
• 1997

This study provides the results of two different blasting methods applied at the H Telcon construction site in Yeon-dong, Cheju Island. One is the traditional blasting method without bottom-hole stemming and the other with bottom-hole stemming using the materials such as sand, polystyrene and sawdust in 5~10 cm lengths. The effect of these materials on vibration level was studied. Assuming that safety criterion of vibration level be 0.5cm/set, 95% confidence limit line of measured data shows that maximum charge weight per delay could be increased in the following order; traditional methed, polystyrene stemming, sand stemming, sawdust stemming.

• 산업경영시스템학회지
• /
• 제30권2호
• /
• pp.8-14
• /
• 2007

The powder blasting process has become an important machining technique for the cost effective fabrication of micro devices. This process is similar to sand blasting, and effectively removes hard and brittle materials. A large number of investigations on the abrasive jet machining with such output parameters as material removal rate, penetration and surface roughness have been carried out and reported by various authors. To achieve higher surface roughness, to increase material removal rate and to identify the influence of blasting parameters on the output parameters, we use the taguchi method which is one of the design methods of experiments. We can select process parameters to optimize the blasting process of glass. Experimental results indicate that the taguchi method is useful as a robust design methodology for the powder blasting process.

• 터널과지하공간
• /
• 제32권4호
• /
• pp.272-284
• /
• 2022

본 연구에서는 개발 중인 전단농화유체(shear thickening fluid) 기반의 발파전색재료와 밀폐 플러그 장치의 효과를 평가하기 위하여 터널발파를 수행하였다. SAV-Cut공법을 적용하고 있는 터널현장에 STF 단일전색 및 STF 전색재를 플러그와 결합하여 적용하였고, 기존 방식의 모래전색을 적용한 케이스와 굴진율 및 파쇄입도를 비교하였다. 터널 굴진율은 3차원 레이저 스캐너를 이용하여 평가하였다. STF 전색재료와 STF 전색재료에 플러그를 결합한 경우 모래전색 대비 각 5.7, 5.36% 정도 굴진율이 향상되는 것을 확인하였다. 파쇄입도의 경우 STF 전색재료를 적용하였을 경우 가장 좋게 나타났으며, 모래 전색케이스와 비교하였을 때 약 61% 파쇄입도가 감소하였다. 그러나 플러그 장치적용에 따른 뚜렷한 발파 효과 향상은 관찰되지 않았다.

• 화약ㆍ발파
• /
• 제23권3호
• /
• pp.83-89
• /
• 2005

철골구조물의 노후화에 따라 리모델링 및 해체시기가 도래함에 따라 시공성, 경제성, 안정성 및 환경성을 고려한 노후 철골구조물의 처리방안에 대한 방법들이 모색되고 있다. 현재 H형강의 절단은 산소절단에 의한 방법이 주로 사용되고 있으나, 순간적으로 구조물을 취약화를 시켜 건물을 붕괴시키는 발파해체공법은 아직까지 적용되고 있지 않다. 따라서 본 연구에서는 철골구조물의 발파해체에 필요한 성형폭약(shape charge)을 이용하여 H형강의 절단방법에 대한 요소시험을 실시하였다. 그 결과 사전 절단방법과 부재의 두께에 따른 단면$\cdot$양면 절단방법을 도출하였고, 성형폭약 고정장치에 따른 부착방법과 그 용이성을 확인하였다. 또한, 성형폭약을 이용하여 절단시 발생하는 소음을 저감하기 위하여 방호박스를 이용한 절단시험결과 약 8dB(A)의 저감효과가 나타났으나, 향후 도심지에서의 구조물 해체를 고려한다면 규제기준이하로 소음을 제어할 수 있는 방법에 대한 추가연구가 필요할 것으로 사료된다.

• Restorative Dentistry and Endodontics
• /
• 제20권2호
• /
• pp.487-507
• /
• 1995

Composite resin repair requires strong bond strength between the new and old materials. The objective of the current study was to identify the optimal treatments for sufficient bond strengths. Bondings between same kinds of materials and cross bondings using chemical curing composites and light curing composites were tested. Surface treatments included the methods of sand-blasting, acid etching and coating of bonding agent. Seven kinds cases of combinations from three kinds of methods were experimented and compared with a control group of which surfaces were highly polished. Measurements of shear bond strength and observations of surface morphologic changes using a scanning electron microscope were done. Following conclusions were drawn : 1. The highest bond strength among composite resins were exhibited by the treatment of the sand-blasting and the coating of bonding agent. 2. Acid etched surfaces showed the lowest bond strength. Bond strengths obtained from experimental groups including acid etching were lower than those obtained from same kinds of experimental groups without acid etching. 3. Simple method of the coating of bonding agent produced the slightly increased bond strength on chemical curing composite and reduced bond strength on light curing composite. 4. Bonding surfaces of chemical curing composite resin showed slightly higher bond strengths than light curing composite resin, however significant differences were not confirmed statistically. 5. More significant irregular surfaces were created by sand-blasting method than acid etching method. 6. A principal component of fillers of both resins was silicon. Acid etching method produced the seperations and degradations of fillers, these were significant on light curing composite resins which containing barium fillers.

• 한국환경복원기술학회지
• /
• 제13권1호
• /
• pp.93-102
• /
• 2010

Greening sometimes fails because its method is not suitable for various site conditions, therefore the trend of selecting a revegetation method in Korea today is through test construction. However, due to enlargement, complication and diversification of domestic construction businesses, the importance of VE is gradually increasing as effective efforts over a whole life-cycle to obtain goals such as quality improvement and cost reduction, and not only quality and economic efficiency but also substantiality need to be considered in comparing revegetation methods. For this study, Sungnam~Janghowon (area1), where comparatively various slope revegetation methods are used, was selected the investigation site. The site was divided into three areas:blasting rock, ripping rock and earth sand. The revegetation methods used were six in the blasting rock area, five in the ripping rock area, and two in the earth sand region. 2007 monitoring data was analyzed, and Value (V) was calculated with LCC related ratio, and compared and contrasted with the evaluation of prior revegetation methods. Therefore it is believed that this analysis enables selection of the most appropriate method, unbiased towards one particular characteristic such as quality, vegetation growth and economy. When aiming for a durable effect, it shall be more efficient to select the most appropriate method focusing on LCC analysis, which deals with the economic aspect, as well as the design function aspect.

• 한국해양공학회지
• /
• 제19권6호통권67호
• /
• pp.72-77
• /
• 2005

The materials used in a ship screw propeller are commonly made with brass. The seawater corrosion and seawater cavitation of the screw propeller reduces the propulsive performance of the ship. In screw manufacturing, the corrosion rust of the screw propeller is removed through a hand grinding method. The grinding process produces dust of the heavy metals from the brass. The dust creates a poor working environment that is harmful to the health of the workers. An automatic corrosionrust removing apparatus, using a blasting method, was developed for the improvement of screw polishing conditions and its working environment. The performance of this apparatus was investigated by surface roughness, weight loss rate, hardness, electrochemical corrosion resistance, and cavitation erosion, after removing of the corrosion rust under various blasting conditions. Two medias of alumina and emery were used in this experiment. The surface roughness and hardness of the screw were improved by this apparatus. The electrochemical corrosion potential (Ecorr) and current density (Icorr) were measured by the dynamic polarization method, using a potentiostat,under the conditions of surface polishing with grinding, blasting, wire brushing, and fine sand papering. The test results prove that the new corrosion rust-removing apparatus improves the surface performance of a screw propeller.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.157.2-157.2
• /
• 2016

Water repellent surfaces may enhance the condensation by efficiently removing the condensed droplets. However, such surfaces may lose their original performance as they are exposed to external mechanical stresses. In this work, we fabricated spray-coated mechanically robust superhydrophobic surfaces using treated titanium dioxide (Type 1) or silica particles (Type 2). Then we compared the mechanical robustness of such surfaces with the silane-coated superhydrophobic surface and PEEK coated surface using a controlled-sand blasting method. The results show that the spray-coated samples can maintain the same level of the contact angle hysteresis than silane-coated superhydorphobic surface after sand blasting at 2 bar. The spray-coating method was applied to the tube type condenser and the condensation behaviors were observed within the environmental chamber with controlled pressure, humidity and non-condensable gas. Previously-reported droplet jumping was observed in the early stage of the condensation event, but soon the droplet jumping stopped and only dropwise condensation was observed since the condensed droplets were pinned on the cracks at spray-coated surfaces. The static contact angle decreases from $158.0^{\circ}$ to $133.2^{\circ}$, and hysteresis increases from $3.0^{\circ}$ to $23.5^{\circ}$ when active condensation occurs on such surfaces. This work suggests the benefits and limitation of spray-coated superhydrophobic condensers and help develop advanced condensers for practical use.