• Steel and Composite Structures
• /
• v.46 no.1
• /
• pp.53-73
• /
• 2023

Man-made structure materials like concrete usually contain inclusions. These inclusions affect the mechanical properties of concrete. In this investigation, the influence of inclusion length and inclination angle on three-dimensional failure mechanism of concrete under uniaxial compression were performed using experimental test and numerical simulation. Approach of acoustic emission were jointly used to analyze the damage and fracture process. Besides, by combining the stress-strain behavior, quantitative determination of the thresholds of crack stress were done. concrete specimens with dimensions of 120 mm × 150 mm × 100 mm were provided. One and two holes filled by gypsum are incorporated in concrete samples. To build the inclusion, firstly cylinder steel tube was pre-inserting into the concrete and removing them after the initial hardening of the specimen. Secondly, the gypsum was poured into the holes. Tensile strengths of concrete and gypsum were 2.45 MPa and 1.5 MPa, respectively. The angle bertween inclusions and axial loadind ary from 0 to 90 with increases of 30. The length of inclusion vary from 25 mm to 100 mm with increases of 25 mm. Diameter of the hole was 20 mm. Entirely 20 various models were examined under uniaxial test. Simultaneous with experimental tests, numerical simulation (Particle flow code in two dimension) were carried out on the numerical models containing the inclusions. The numerical model were calibrated firstly by experimental outputs and then failure behavior of models containing inclusions have been investigated. The angle bertween inclusions and axial loadind vary from 0 to 90 with increases of 15. The length of inclusion vary from 25 mm to 100 mm with increases of 25 mm. Entirely 32 various models were examined under uniaxial test. Loading rate was 0.05 mm/sec. The results indicated that when inclusion has occupied 100% of sample thickness, two tensile cracks originated from boundaries of sample and spread parallel to the loading direction until being integrated together. When inclusion has occupied 75% of sample thickness, four tensile cracks originated from boundaries of sample and spread parallel to the loading direction until being integrated together. When inclusions have occupied 50% and 25% of sample thickness, four tensile cracks originated from boundaries of sample and spread parallel to the loading direction until being integrated together. Also the inclusion was failed by one tensile crack. The compressive strength of samples decease with the decreases of the inclusions length, and inclusion angle had some effects on that. Failure of concrete is mostly due to the tensile crack. The behavior of crack, was affected by the inclusion length and inclusion number.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.12
• /
• pp.1099-1107
• /
• 1998

In this study, the microstructure and electric conductivity of 5mol% $Gd_2O_3$-5mol% $Y_2O_3-ZrO_2$ system(5G5YZ) with a variation of sintering time at $1600^{\circ}C$ were investigated. By the result of TEM analysis of 5G5YZ sintered for 12h, a microcrack was observed near grain boundary. The change of the sintering time did not affect the lattice conductivity, but the grain boundary contribution was varied with the sintering time. The grain boundary conductivity of the sample sintered for 1h showed the highest value. Furthermore, the activation energy of the total conductivity was independent upon the sintering time and showed approximately 1.01eV. The highest conductivity measured at $1000^{\circ}C$ was 0.0197S/cm with the sample sintered for 1h. Comparing to 0h’s, the thickness ration of grain boundary as a function of sintering time were 0.88, 1.11 and 1.29 for 1h, 5h and 12h, respectively. In case of the sample sintered for 1h, the thickness of the grain boundary showed the lowest value. The increase of the sintering time over 1h made the decrease of the electric conductivity as well as the increase of the grain growth and the thickness of the grain boundary. As a result, it seemed that the proper sintering time for 5G5YZ composition was 1h.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.2
• /
• pp.84-91
• /
• 2011

The purpose of this study is to find how to be formed the wet film thickness during the low friction coating process for a piston skirt with application to the theory of screen printing. In other words, the general expressions predicting the pressure under a blade and the volume of coating fluid passing through the blade edge are derived. Using these expressions, the coating thickness on a piston skirt during a sample blade coating process can be quantitatively assessed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.305-313
• /
• 2010

HDPE smooth and textured GMs were cut into dumbbell shape and notched where depth of the notch produced a ligament thickness of 90% to 10% of the nominal thickness of the specimen at 10% interval. Yield stress and elongation were measured of those samples and plotted on Graph. Yield stress and elongation at yield point decreases gradually as the notch depth is increased. Both installations damaged and notched GMs were used to understand stress crack behavior. Intact sample were notched in such a manner that the depth of notch produced a ligament thickness of 80% of the nominal thickness of the specimen. Installation damaged samples were not notched. Stress Crack Resistance behavior was observed using NCTL Test at $50{\pm}1^{\circ}C$ at different yield stresses immerging with pH 4 and pH 12 buffer solutions. Significant difference was observed in both cases.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.11a
• /
• pp.7-10
• /
• 1992

CoNiCr/Cr and CoCrTa/Cr for longitudinal magnetic recording media were. prepared on Coming 7059 glass by RF magnetron sputtering. The thickness of Cr underlayer was varied from 500 to $3000{\AA}$ and. that of magnetic layer was $700{\AA}$. Coercivity and squareness were measured using V.S.M.(vibrating sample magnetometer). The coercivity of films increased with increasing Cr thickness when the films were unannealed. The coercivity of the films annealed in a 10 mtorr vacuum increased initially with annealing time and then saturated with further increase in annealing time. The coercivity value difference between the unannealed and annealed films increased with increasing the thickness of Cr underlayer No significant change was found in squareness after anneal, regardless of Cr underlayer thickness.

• Proceedings of the KIEE Conference
• /
• 1988.07a
• /
• pp.43-46
• /
• 1988

In this paper, a methodology for determination of the thickness of layer on a substrate using reflection acoustic microscope has been presented. It has been shown that the amplitude and the phase of reflection coefficient of the layer-substrate composite has been used for measurement of layer thickness, acoustic velosity, mass density of the layer material. The reflection acoustic microscope operating at a frequency of 15 MHz has been used for the experiment and the measured acoustic impedance value for aluminum sample has agreed with the published data, and the measured layer thickness for silver-glass composite has agreed with that measured using micrometer.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.84-86
• /
• 2007

Aluminum sheets were asymmetrically cold rolled without lubrication by using different roll velocities of upper and lower rolls in order to intensify the shear deformation. During asymmetrical cold rolling of aluminum sheets, a reduction per a rolling pass, initial sheet thickness, roll diameter, roll velocity ratio were varied to investigate the effect of rolling parameters. The formation of through thickness shear texture was related to the ratio of the contact length between the roll and sample($l_c$) to the sheet thickness(d). The strain states associated with asymmetrical rolling were investigated by the finite element method (FEM) simulation. FEM results indicated that the evolution of deformation texture in a thickness layer is strongly governed by integrated values of strain rates $\dot{\varepsilon}_{13}$ and $\dot{\varepsilon}_{11}$ along the streamline in the roll gap.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.2
• /
• pp.153-158
• /
• 2010

The crystallization of FePt/MgO(001) magnetic thin films of various thicknesses has been studied using synchrotron x-ray scattering, atomic force microscope, and vibrating sample magnetometer. In film with a 499-$\AA$-thick, face-centered tetragonal, ordered FePt phase was dominantly crystallized into perpendicular (001) grains keeping the magnetically easy c-axis normal to the film plane during annealing. In film with a 816-$\AA$-thick, however, longitudinal (110) grains keeping the c-axis parallel to the film plane were grown on top of the perpendicular (001) grains. The behavior of the magnetic properties was consistent with the thickness dependence of the crystallization. We attribute the thickness dependence of the crystallization to the substrate effect, which prefers the growth of the c-axis oriented perpendicular grains near the film/substrate interfacial area.

• Journal of Surface Science and Engineering
• /
• v.31 no.5
• /
• pp.261-265
• /
• 1998

We investigated compositional separation of Co-23%Cr magnetic alloy thin films with varying film thicknesses. Saturation magnetization and magnetic microstructures were investigated using vibrating sample magnetometer (VSM) and scanning probe microscope (SPM), respectively. Saturation magnetization was as 700 emu/cc for films below 50 nm-thick, and changed to 430 emu/cc for the ones above 2000 nm-thick. This may be due to increment of molar volume of Cr-enriched phase as film thickness increases. The surface grain size in AFM (atomic force microscope) measurement becomes larger as film thickness increases. The MFM (magnetic force microscope) reveals that magnetic microstructure is changed from the fine spherical domains to the maze type domains as film thickness increases. We conclude that employing thickness of Co-22%Cr films below 50 nm is favorable for high density recording in order to enhance perpendicular saturation magnetization and SNR (signal to noise ratio).

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.2
• /
• pp.192-198
• /
• 1992

The electrical properties of the ultrasonic probes and the piezoelectric composite materials with 1-3 connectivity by the extrusion method have been studied. The relative permittivity and piezoelectric coefficient increase linearly as PZT volume% increases and resonance frequency moves to low frequency as the sample thickness increases. The acoustic impedance matching with body and water is better than PZT ceramics' and the reception sensitivity is fine as the thickness thins down.